http://bugzilla.kernel.org/show_bug.cgi?id=6654
------- Additional Comments From [EMAIL PROTECTED] 2006-06-06 11:04 -------
No, booting with pci=routeirq doesn't work correctly.
I don't see any IRQ error messages anymore but I only get full speed (12 Mbps)
instead of high speed (480Mbps).
So far only acpi=noirq allows me to get high speed mode.
dmesg
=====
rface v0.101 (c) Dave Jones
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:09: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378, irq 7 [PCSPP(,...)]
floppy0: no floppy controllers found
loop: loaded (max 8 devices)
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:0f.0
ACPI: PCI Interrupt 0000:00:0f.0[A] -> Link [LNKA] -> GSI 10 (level, low) ->
IRQ 10
PCI: VIA IRQ fixup for 0000:00:0f.0, from 255 to 10
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on pci0000:00:0f.0
ide0: BM-DMA at 0xd800-0xd807, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xd808-0xd80f, BIOS settings: hdc:DMA, hdd:DMA
Probing IDE interface ide0...
hda: ST3160021A, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: HL-DT-ST DVDRAM GSA-4167B, ATAPI CD/DVD-ROM drive
hdd: ST340810A, ATA DISK drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 512KiB
hda: 312581808 sectors (160041 MB) w/2048KiB Cache, CHS=19457/255/63, UDMA(100)
hda: cache flushes supported
hda: hda1 hda2 < hda5 >
hdd: max request size: 128KiB
hdd: 78165360 sectors (40020 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(100)
hdd: cache flushes not supported
hdd: hdd1 hdd2 hdd3
hdc: ATAPI 48X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
libata version 1.20 loaded.
usbmon: debugfs is not available
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
mice: PS/2 mouse device common for all mice
Advanced Linux Sound Architecture Driver Version 1.0.11rc2 (Wed Jan 04 08:57:20
2006 UTC).
ALSA device list:
No soundcards found.
oprofile: using timer interrupt.
NET: Registered protocol family 2
input: AT Translated Set 2 keyboard as /class/input/input0
IP route cache hash table entries: 8192 (order: 3, 32768 bytes)
TCP established hash table entries: 32768 (order: 5, 131072 bytes)
TCP bind hash table entries: 32768 (order: 5, 131072 bytes)
TCP: Hash tables configured (established 32768 bind 32768)
TCP reno registered
ip_conntrack version 2.4 (4095 buckets, 32760 max) - 172 bytes per conntrack
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI Shortcut mode
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 152k freed
kjournald starting. Commit interval 5 seconds
input: ImPS/2 Generic Wheel Mouse as /class/input/input1
Adding 2096472k swap on /dev/hdd3. Priority:-1 extents:1 across:2096472k
EXT3 FS on hda1, internal journal
lp0: using parport0 (interrupt-driven).
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda5, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hdd2, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
agpgart: Detected VIA KT400/KT400A/KT600 chipset
agpgart: AGP aperture is 128M @ 0xd0000000
ne2k-pci.c:v1.03 9/22/2003 D. Becker/P. Gortmaker
http://www.scyld.com/network/ne2k-pci.html
ACPI: PCI Interrupt 0000:00:0b.0[A] -> Link [LNKD] -> GSI 11 (level, low) ->
IRQ 11
eth0: RealTek RTL-8029 found at 0xd000, IRQ 11, 00:C0:DF:F5:1A:C9.
ACPI: PCI Interrupt 0000:00:0c.0[A] -> Link [LNKC] -> GSI 10 (level, low) ->
IRQ 10
gameport: ES137x is pci0000:00:0c.0/gameport0, io 0x200, speed 962kHz
input: Microsoft SideWinder Force Feedback Pro as /class/input/input2
USB Universal Host Controller Interface driver v2.3
ACPI: PCI Interrupt 0000:00:10.0[A] -> Link [LNKA] -> GSI 10 (level, low) ->
IRQ 10
uhci_hcd 0000:00:10.0: UHCI Host Controller
uhci_hcd 0000:00:10.0: detected 2 ports
uhci_hcd 0000:00:10.0: uhci_check_and_reset_hc: cmd = 0x0000
uhci_hcd 0000:00:10.0: Performing full reset
drivers/usb/core/inode.c: creating file 'devices'
drivers/usb/core/inode.c: creating file '001'
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:10.0: irq 10, io base 0x0000dc00
usb usb1: default language 0x0409
usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: UHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.16.18 uhci_hcd
usb usb1: SerialNumber: 0000:00:10.0
usb usb1: uevent
usb usb1: device is self-powered
usb usb1: configuration #1 chosen from 1 choice
usb usb1: adding 1-0:1.0 (config #1, interface 0)
usb 1-0:1.0: uevent
hub 1-0:1.0: usb_probe_interface
hub 1-0:1.0: usb_probe_interface - got id
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
hub 1-0:1.0: standalone hub
hub 1-0:1.0: no power switching (usb 1.0)
hub 1-0:1.0: individual port over-current protection
hub 1-0:1.0: power on to power good time: 2ms
hub 1-0:1.0: local power source is good
hub 1-0:1.0: state 7 ports 2 chg 0000 evt 0000
drivers/usb/core/inode.c: creating file '001'
uhci_hcd 0000:00:10.0: port 1 portsc 008a,00
hub 1-0:1.0: port 1, status 0100, change 0003, 12 Mb/s
ACPI: PCI Interrupt 0000:00:10.1[A] -> Link [LNKA] -> GSI 10 (level, low) ->
IRQ 10
uhci_hcd 0000:00:10.1: UHCI Host Controller
uhci_hcd 0000:00:10.1: detected 2 ports
uhci_hcd 0000:00:10.1: uhci_check_and_reset_hc: cmd = 0x0000
uhci_hcd 0000:00:10.1: Performing full reset
drivers/usb/core/inode.c: creating file '002'
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:10.1: irq 10, io base 0x0000e000
usb usb2: default language 0x0409
usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: UHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.16.18 uhci_hcd
usb usb2: SerialNumber: 0000:00:10.1
usb usb2: uevent
usb usb2: device is self-powered
usb usb2: configuration #1 chosen from 1 choice
usb usb2: adding 2-0:1.0 (config #1, interface 0)
usb 2-0:1.0: uevent
hub 2-0:1.0: usb_probe_interface
hub 2-0:1.0: usb_probe_interface - got id
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
hub 2-0:1.0: standalone hub
hub 2-0:1.0: no power switching (usb 1.0)
hub 2-0:1.0: individual port over-current protection
hub 2-0:1.0: power on to power good time: 2ms
hub 2-0:1.0: local power source is good
drivers/usb/core/inode.c: creating file '001'
ACPI: PCI Interrupt 0000:00:10.2[B] -> Link [LNKB] -> GSI 11 (level, low) ->
IRQ 11
uhci_hcd 0000:00:10.2: UHCI Host Controller
uhci_hcd 0000:00:10.2: detected 2 ports
uhci_hcd 0000:00:10.2: uhci_check_and_reset_hc: cmd = 0x0000
uhci_hcd 0000:00:10.2: Performing full reset
drivers/usb/core/inode.c: creating file '003'
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:10.2: irq 11, io base 0x0000e400
usb usb3: default language 0x0409
usb usb3: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: UHCI Host Controller
usb usb3: Manufacturer: Linux 2.6.16.18 uhci_hcd
usb usb3: SerialNumber: 0000:00:10.2
usb usb3: uevent
usb usb3: device is self-powered
usb usb3: configuration #1 chosen from 1 choice
usb usb3: adding 3-0:1.0 (config #1, interface 0)
usb 3-0:1.0: uevent
hub 3-0:1.0: usb_probe_interface
hub 3-0:1.0: usb_probe_interface - got id
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
hub 3-0:1.0: standalone hub
hub 3-0:1.0: no power switching (usb 1.0)
hub 3-0:1.0: individual port over-current protection
hub 3-0:1.0: power on to power good time: 2ms
hub 3-0:1.0: local power source is good
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x100
uhci_hcd 0000:00:10.0: port 2 portsc 018a,00
hub 1-0:1.0: port 2, status 0300, change 0003, 1.5 Mb/s
drivers/usb/core/inode.c: creating file '001'
ACPI: PCI Interrupt 0000:00:10.3[B] -> Link [LNKB] -> GSI 11 (level, low) ->
IRQ 11
uhci_hcd 0000:00:10.3: UHCI Host Controller
uhci_hcd 0000:00:10.3: detected 2 ports
uhci_hcd 0000:00:10.3: uhci_check_and_reset_hc: cmd = 0x0000
uhci_hcd 0000:00:10.3: Performing full reset
drivers/usb/core/inode.c: creating file '004'
uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:10.3: irq 11, io base 0x0000e800
usb usb4: default language 0x0409
usb usb4: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb4: Product: UHCI Host Controller
usb usb4: Manufacturer: Linux 2.6.16.18 uhci_hcd
usb usb4: SerialNumber: 0000:00:10.3
usb usb4: uevent
usb usb4: device is self-powered
usb usb4: configuration #1 chosen from 1 choice
usb usb4: adding 4-0:1.0 (config #1, interface 0)
usb 4-0:1.0: uevent
hub 4-0:1.0: usb_probe_interface
hub 4-0:1.0: usb_probe_interface - got id
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
hub 4-0:1.0: standalone hub
hub 4-0:1.0: no power switching (usb 1.0)
hub 4-0:1.0: individual port over-current protection
hub 4-0:1.0: power on to power good time: 2ms
hub 4-0:1.0: local power source is good
hub 1-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x300
hub 1-0:1.0: state 7 ports 2 chg 0000 evt 0000
hub 2-0:1.0: state 7 ports 2 chg 0000 evt 0006
uhci_hcd 0000:00:10.1: port 1 portsc 008a,00
hub 2-0:1.0: port 1, status 0100, change 0003, 12 Mb/s
drivers/usb/core/inode.c: creating file '001'
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x100
uhci_hcd 0000:00:10.1: port 2 portsc 018a,00
hub 2-0:1.0: port 2, status 0300, change 0003, 1.5 Mb/s
hub 2-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x300
hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0006
uhci_hcd 0000:00:10.2: port 1 portsc 008a,00
hub 3-0:1.0: port 1, status 0100, change 0003, 12 Mb/s
hub 3-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x100
uhci_hcd 0000:00:10.2: port 2 portsc 008a,00
hub 3-0:1.0: port 2, status 0100, change 0003, 12 Mb/s
ehci_hcd: block sizes: qh 128 qtd 96 itd 192 sitd 96
ACPI: PCI Interrupt 0000:00:10.4[C] -> Link [LNKC] -> GSI 10 (level, low) ->
IRQ 10
ehci_hcd 0000:00:10.4: EHCI Host Controller
ehci_hcd 0000:00:10.4: reset hcs_params 0x4208 dbg=0 cc=4 pcc=2 ordered !ppc
ports=8
ehci_hcd 0000:00:10.4: reset hcc_params 6872 thresh 7 uframes 256/512/1024
ehci_hcd 0000:00:10.4: MWI active
drivers/usb/core/inode.c: creating file '005'
ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 5
ehci_hcd 0000:00:10.4: irq 10, io mem 0xe2000000
ehci_hcd 0000:00:10.4: reset command 080002 (park)=0 ithresh=8 period=1024 Reset
HALT
ehci_hcd 0000:00:10.4: init command 010009 (park)=0 ithresh=1 period=256 RUN
ehci_hcd 0000:00:10.4: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb5: default language 0x0409
usb usb5: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb5: Product: EHCI Host Controller
usb usb5: Manufacturer: Linux 2.6.16.18 ehci_hcd
usb usb5: SerialNumber: 0000:00:10.4
usb usb5: uevent
usb usb5: device is self-powered
usb usb5: configuration #1 chosen from 1 choice
usb usb5: adding 5-0:1.0 (config #1, interface 0)
usb 5-0:1.0: uevent
hub 5-0:1.0: usb_probe_interface
hub 5-0:1.0: usb_probe_interface - got id
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 8 ports detected
hub 5-0:1.0: standalone hub
hub 5-0:1.0: no power switching (usb 1.0)
hub 5-0:1.0: individual port over-current protection
hub 5-0:1.0: Single TT
hub 5-0:1.0: TT requires at most 8 FS bit times (666 ns)
hub 5-0:1.0: power on to power good time: 20ms
hub 5-0:1.0: local power source is good
hub 3-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x100
hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0006
uhci_hcd 0000:00:10.3: port 1 portsc 008a,00
hub 4-0:1.0: port 1, status 0100, change 0003, 12 Mb/s
drivers/usb/core/inode.c: creating file '001'
hub 4-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x100
uhci_hcd 0000:00:10.3: port 2 portsc 018a,00
hub 4-0:1.0: port 2, status 0300, change 0003, 1.5 Mb/s
hub 4-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x300
hub 2-0:1.0: state 7 ports 2 chg 0000 evt 0000
hub 5-0:1.0: state 7 ports 8 chg 0000 evt 0000
hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000
uhci_hcd 0000:00:10.0: suspend_rh (auto-stop)
uhci_hcd 0000:00:10.1: suspend_rh (auto-stop)
uhci_hcd 0000:00:10.2: suspend_rh (auto-stop)
uhci_hcd 0000:00:10.3: suspend_rh (auto-stop)
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
ACPI: Sleep Button (CM) [SLPB]
ACPI: Fan [FAN] (on)
nvidia: module license 'NVIDIA' taints kernel.
ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNKA] -> GSI 10 (level, low) ->
IRQ 10
NVRM: loading NVIDIA Linux x86 Kernel Module 1.0-8762 Mon May 15 13:06:38 PDT
2006
agpgart: Found an AGP 3.5 compliant device at 0000:00:00.0.
agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode
agpgart: Putting AGP V3 device at 0000:01:00.0 into 8x mode
hub 5-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:10.4: GetStatus port 1 status 001803 POWER sig=j CSC CONNECT
hub 5-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
ehci_hcd 0000:00:10.4: GetStatus port 1 status 001002 POWER sig=se0 CSC
hub 5-0:1.0: debounce: port 1: total 175ms stable 100ms status 0x100
hub 5-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:10.4: GetStatus port 1 status 001803 POWER sig=j CSC CONNECT
hub 5-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
hub 5-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:10.4: port 1 high speed
ehci_hcd 0000:00:10.4: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
usb 5-1: new high speed USB device using ehci_hcd and address 2
ehci_hcd 0000:00:10.4: port 1 high speed
ehci_hcd 0000:00:10.4: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
usb 5-1: default language 0x0409
usb 5-1: new device strings: Mfr=1, Product=2, SerialNumber=3
usb 5-1: Product: External HDD
usb 5-1: Manufacturer: Western Digital
usb 5-1: SerialNumber: 57442D574D414E5531303836373034
usb 5-1: uevent
usb 5-1: device is self-powered
usb 5-1: configuration #1 chosen from 1 choice
usb 5-1: adding 5-1:1.0 (config #1, interface 0)
usb 5-1:1.0: uevent
drivers/usb/core/inode.c: creating file '002'
Initializing USB Mass Storage driver...
usb-storage 5-1:1.0: usb_probe_interface
usb-storage 5-1:1.0: usb_probe_interface - got id
scsi0 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
Vendor: WD Model: 4000KS External Rev: 101a
Type: Direct-Access ANSI SCSI revision: 04
SCSI device sda: 781422768 512-byte hdwr sectors (400088 MB)
sda: Write Protect is off
sda: Mode Sense: 11 00 00 00
sda: assuming drive cache: write through
SCSI device sda: 781422768 512-byte hdwr sectors (400088 MB)
sda: Write Protect is off
sda: Mode Sense: 11 00 00 00
sda: assuming drive cache: write through
sda: sda1
sd 0:0:0:0: Attached scsi disk sda
sd 0:0:0:0: Attached scsi generic sg0 type 0
usb-storage: device scan complete
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
------- You are receiving this mail because: -------
You are the assignee for the bug, or are watching the assignee.
_______________________________________________
acpi-bugzilla mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/acpi-bugzilla
