Coyle, Thank u so much for ur guidance in solving the problem which made me mad.I have given "audit library autolib" and the process has started. I will try restore, after it has finished. thank u once again
Geetha Thanu Bioinformatics CDFD,Hyderabad. ---------REPLY TO------------- Date:Fri Nov 21 16:51:36 CST 2003 FROM: Coyle, Jack <[EMAIL PROTECTED]> To: [EMAIL PROTECTED] Subject: Re: increasing mount point You should not have to stop and start the server. From a drive / path perspective, everything is as good as it is going to get. However, your original append did show that the TSM server viewed the status of the contents of your AUTOLIB library as inconsistent, The error message that you listed ANR8358E Audit operation is required for library AUTOLIB indicates that, at a minimum, a library audit is in order before proceeding further. Issue the command audit library autolib to allow the server to re-inventory the tapes that are in the library. If that completes successfully, then you should be ready to use the library again. If you would like to verify that before diving into a restore operation, see if you can check one of your scratch tapes in that library out and then back in. That should exercise both of the drives and verify that they are, once again, operational. HTH. Regards, Jack Coyle Rex Healthcare [EMAIL PROTECTED] > ---------- > From: Geetha Thanu[SMTP:[EMAIL PROTECTED] > Reply To: ADSM: Dist Stor Manager > Sent: Friday, November 21, 2003 4:10 PM > To: [EMAIL PROTECTED] > Subject: Re: increasing mount point > > Coyle, > > As u told i have given the commands and now query path gives > the following result > > ANR1722I A path from SERVER1 to AUTOLIB DRIVE01 has been updated. > > ANR1722I A path from SERVER1 to AUTOLIB DRIVE02 has been updated. > > Source Name Source Type Destination Destination On-Line > Name Type > ----------- ----------- ----------- ----------- ------- > SERVER1 SERVER AUTOLIB LIBRARY Yes > SERVER1 SERVER DRIVE01 DRIVE Yes > SERVER1 SERVER DRIVE02 DRIVE Yes > > Hope now evrything is fine.shld I have to start and stop the server > can I try restoring things now.Pls reply. > > Thank u so much for helping. > Geetha Thanu > Bioinformatics > CDFD,Hyderabad. > > > > > > > > > > ---------REPLY TO------------- > Date:Fri Nov 21 15:51:09 CST 2003 > FROM: Coyle, Jack <[EMAIL PROTECTED]> > To: [EMAIL PROTECTED] > Subject: Re: increasing mount point > Try the following two commands: > > update path server1 drive01 srctype=server desttype=drive library=autolib > online=yes > update path server1 drive02 srctype=server desttype=drive library=autolib > online=yes > > Assuming they execute without error, follow with a "query path" command > to > see if the paths to the drives are now online. > > HTH. > > Regards, > Jack Coyle > Rex Healthcare > [EMAIL PROTECTED] > > > > ---------- > > From: Geetha Thanu[SMTP:[EMAIL PROTECTED] > > Reply To: ADSM: Dist Stor Manager > > Sent: Friday, November 21, 2003 2:51 PM > > To: [EMAIL PROTECTED] > > Subject: Re: increasing mount point > > > > Coyle, > > > > Thank u Coyle for ur immediate reply.As u said I have given the query > > drive > > and query path and the results r as below > > > > Library Name Drive Name Device Type On-Line > > ------------ ------------ ----------- ------------------- > > AUTOLIB DRIVE01 DLT Yes > > AUTOLIB DRIVE02 DLT Yes > > > > > > > > > > Source Name Source Type Destination Destination On-Line > > Name Type > > ----------- ----------- ----------- ----------- ------- > > SERVER1 SERVER AUTOLIB LIBRARY Yes > > SERVER1 SERVER DRIVE01 DRIVE No > > SERVER1 SERVER DRIVE02 DRIVE No > > > > From the above result I feel the drives are online but > > the AUTOLIB library is not online. > > Now what I should do to put it on line and make the server > > work as normal as before.Pls guide me to proceed. > > Thanks to all who guide with my problems > > > > Thank u > > Geetha Thanu > > > > > > > > > > > > > > > > > > > > > > - > > > > > > - > > -