2010/12/1, david carrasco <[email protected]>: >> Greetings to all good I hope to help me >> I followed the manual gateway-firewall openbsd 4.8 >> but still can not get or have no internet Conexxion client >> >> ADSL (router ext) >> >> 192.168.1.1 >> | >> | >> xl0 >> 192.168.1.101 >> gatewayopenbsd4.8- >> xl1 >> 192.168.0.1 >> | >> | >> Client >> 192.168.0.10 >> I have attached a number of client files and >> gateway (route, ping, pf, dhcp, rc, sysctl, messages, dmesg, etc) of >> configuration. >> >> Grateful for your help I hope >> is that your experience would be helpful to this newbie > > ///////////////////////////////////////////////////////////////////////////////////////////////////////////////////// > //////////////////////////// INFORMATION GATEWAY > //////////////////////////////////////////////// > ///////////////////////////////////////////////////////////////////////////////////////////////////////////////////// > ************ dmesg********** > > OpenBSD 4.8 (RAMDISK_CD) #89: Mon Aug 16 09:24:20 MDT 2010 > [email protected]:/usr/src/sys/arch/i386/compile/RAMDISK_CD > cpu0: Intel Pentium III ("GenuineIntel" 686-class, 128KB L2 cache) 632 MHz > cpu0: > FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PSE36,MMX,FXSR,SSE > real mem = 199585792 (190MB) > avail mem = 189444096 (180MB) > mainbus0 at root > bios0 at mainbus0: AT/286+ BIOS, date 03/07/01, BIOS32 rev. 0 @ > 0xfda74, SMBIOS rev. 2.3 @ 0xf0ea0 (55 entries) > bios0: vendor Intel Corp. version "A11" date 03/07/2001 > bios0: Dell Computer Corporation L800C > apm0 at bios0: Power Management spec V1.2 > acpi at bios0 function 0x0 not configured > pcibios0 at bios0: rev 2.1 @ 0xf0000/0x10000 > pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xf2f30/192 (10 entries) > pcibios0: PCI Interrupt Router at 000:31:0 ("Intel 82371FB ISA" rev 0x00) > pcibios0: PCI bus #1 is the last bus > bios0: ROM list: 0xc0000/0xc000 0xcc000/0x800 > cpu0 at mainbus0: (uniprocessor) > pci0 at mainbus0 bus 0: configuration mode 1 (bios) > pchb0 at pci0 dev 0 function 0 "Intel 82810 Host" rev 0x03 > vga1 at pci0 dev 1 function 0 "Intel 82810 Video" rev 0x03 > wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation) > ppb0 at pci0 dev 30 function 0 "Intel 82801AA Hub-to-PCI" rev 0x02 > pci1 at ppb0 bus 1 > xl0 at pci1 dev 8 function 0 "3Com 3c905C 100Base-TX" rev 0x30: irq > 11, address 00:01:03:e8:38:4b > ukphy0 at xl0 phy 24: Generic IEEE 802.3u media interface, rev. 0: OUI > 0x00601d, model 0x0035 > xl1 at pci1 dev 9 function 0 "3Com 3c905 100Base-TX" rev 0x00: irq 10, > address 00:60:97:be:ca:2a > nsphy0 at xl1 phy 24: DP83840 10/100 PHY, rev. 1 > ichpcib0 at pci0 dev 31 function 0 "Intel 82801AA LPC" rev 0x02: > 24-bit timer at 3579545Hz > pciide0 at pci0 dev 31 function 1 "Intel 82801AA IDE" rev 0x02: DMA, > channel 0 wired to compatibility, channel 1 wired to compatibility > wd0 at pciide0 channel 0 drive 0: <QUANTUM FIREBALLlct20 10> > wd0: 8-sector PIO, LBA, 9787MB, 20044080 sectors > wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 2 > atapiscsi0 at pciide0 channel 1 drive 1 > scsibus0 at atapiscsi0: 2 targets > cd0 at scsibus0 targ 0 lun 0: <HP, CD-Writer+ 7500, 1.0a> ATAPI > 5/cdrom removable > cd0(pciide0:1:1): using PIO mode 4, DMA mode 2 > uhci0 at pci0 dev 31 function 2 "Intel 82801AA USB" rev 0x02: irq 9 > "Intel 82801AA SMBus" rev 0x02 at pci0 dev 31 function 3 not configured > isa0 at ichpcib0 > isadma0 at isa0 > com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo > pckbc0 at isa0 port 0x60/5 > pckbd0 at pckbc0 (kbd slot) > pckbc0: using irq 1 for kbd slot > wskbd0 at pckbd0: console keyboard, using wsdisplay0 > npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16 > fdc0 at isa0 port 0x3f0/6 irq 6 drq 2 > usb0 at uhci0: USB revision 1.0 > uhub0 at usb0 "Intel UHCI root hub" rev 1.00/1.00 addr 1 > biomask f3ed netmask ffed ttymask ffff > rd0: fixed, 3800 blocks > softraid0 at root > root on rd0a swap on rd0b dump on rd0b > syncing disks... done > rebooting... > OpenBSD 4.8 (GENERIC) #136: Mon Aug 16 09:06:23 MDT 2010 > [email protected]:/usr/src/sys/arch/i386/compile/GENERIC > cpu0: Intel Pentium III ("GenuineIntel" 686-class, 128KB L2 cache) 632 MHz > cpu0: > FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PSE36,MMX,FXSR,SSE > real mem = 199585792 (190MB) > avail mem = 186396672 (177MB) > mainbus0 at root > bios0 at mainbus0: AT/286+ BIOS, date 03/07/01, BIOS32 rev. 0 @ > 0xfda74, SMBIOS rev. 2.3 @ 0xf0ea0 (55 entries) > bios0: vendor Intel Corp. version "A11" date 03/07/2001 > bios0: Dell Computer Corporation L800C > apm0 at bios0: Power Management spec V1.2 > apm0: AC on, battery charge unknown > acpi at bios0 function 0x0 not configured > pcibios0 at bios0: rev 2.1 @ 0xf0000/0x10000 > pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xf2f30/192 (10 entries) > pcibios0: PCI Interrupt Router at 000:31:0 ("Intel 82371FB ISA" rev 0x00) > pcibios0: PCI bus #1 is the last bus > bios0: ROM list: 0xc0000/0xc000 0xcc000/0x800 > cpu0 at mainbus0: (uniprocessor) > pci0 at mainbus0 bus 0: configuration mode 1 (bios) > pchb0 at pci0 dev 0 function 0 "Intel 82810 Host" rev 0x03 > vga1 at pci0 dev 1 function 0 "Intel 82810 Video" rev 0x03 > wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation) > wsdisplay0: screen 1-5 added (80x25, vt100 emulation) > intagp0 at vga1 > agp0 at intagp0: aperture at 0xf8000000, size 0x4000000 > ppb0 at pci0 dev 30 function 0 "Intel 82801AA Hub-to-PCI" rev 0x02 > pci1 at ppb0 bus 1 > xl0 at pci1 dev 8 function 0 "3Com 3c905C 100Base-TX" rev 0x30: irq > 11, address 00:01:03:e8:38:4b > ukphy0 at xl0 phy 24: Generic IEEE 802.3u media interface, rev. 0: OUI > 0x00601d, model 0x0035 > xl1 at pci1 dev 9 function 0 "3Com 3c905 100Base-TX" rev 0x00: irq 10, > address 00:60:97:be:ca:2a > nsphy0 at xl1 phy 24: DP83840 10/100 PHY, rev. 1 > ichpcib0 at pci0 dev 31 function 0 "Intel 82801AA LPC" rev 0x02: > 24-bit timer at 3579545Hz > pciide0 at pci0 dev 31 function 1 "Intel 82801AA IDE" rev 0x02: DMA, > channel 0 wired to compatibility, channel 1 wired to compatibility > wd0 at pciide0 channel 0 drive 0: <QUANTUM FIREBALLlct20 10> > wd0: 8-sector PIO, LBA, 9787MB, 20044080 sectors > wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 2 > atapiscsi0 at pciide0 channel 1 drive 1 > scsibus0 at atapiscsi0: 2 targets > cd0 at scsibus0 targ 0 lun 0: <HP, CD-Writer+ 7500, 1.0a> ATAPI > 5/cdrom removable > cd0(pciide0:1:1): using PIO mode 4, DMA mode 2 > uhci0 at pci0 dev 31 function 2 "Intel 82801AA USB" rev 0x02: irq 9 > ichiic0 at pci0 dev 31 function 3 "Intel 82801AA SMBus" rev 0x02: irq 10 > iic0 at ichiic0 > spdmem0 at iic0 addr 0x50: 128MB SDRAM non-parity PC133CL3 > spdmem1 at iic0 addr 0x51: 64MB SDRAM non-parity PC100CL2 > isa0 at ichpcib0 > isadma0 at isa0 > com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo > pckbc0 at isa0 port 0x60/5 > pckbd0 at pckbc0 (kbd slot) > pckbc0: using irq 1 for kbd slot > wskbd0 at pckbd0: console keyboard, using wsdisplay0 > pcppi0 at isa0 port 0x61 > spkr0 at pcppi0 > lpt0 at isa0 port 0x378/4 irq 7 > npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16 > fdc0 at isa0 port 0x3f0/6 irq 6 drq 2 > usb0 at uhci0: USB revision 1.0 > uhub0 at usb0 "Intel UHCI root hub" rev 1.00/1.00 addr 1 > biomask f76d netmask ff6d ttymask ffff > mtrr: Pentium Pro MTRR support > softraid0 at root > root on wd0a swap on wd0b dump on wd0b > syncing disks... done > rebooting... > OpenBSD 4.8 (GENERIC) #136: Mon Aug 16 09:06:23 MDT 2010 > [email protected]:/usr/src/sys/arch/i386/compile/GENERIC > cpu0: Intel Pentium III ("GenuineIntel" 686-class, 128KB L2 cache) 632 MHz > cpu0: > FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PSE36,MMX,FXSR,SSE > real mem = 199585792 (190MB) > avail mem = 186396672 (177MB) > mainbus0 at root > bios0 at mainbus0: AT/286+ BIOS, date 03/07/01, BIOS32 rev. 0 @ > 0xfda74, SMBIOS rev. 2.3 @ 0xf0ea0 (55 entries) > bios0: vendor Intel Corp. version "A11" date 03/07/2001 > bios0: Dell Computer Corporation L800C > apm0 at bios0: Power Management spec V1.2 > apm0: AC on, battery charge unknown > acpi at bios0 function 0x0 not configured > pcibios0 at bios0: rev 2.1 @ 0xf0000/0x10000 > pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xf2f30/192 (10 entries) > pcibios0: PCI Interrupt Router at 000:31:0 ("Intel 82371FB ISA" rev 0x00) > pcibios0: PCI bus #1 is the last bus > bios0: ROM list: 0xc0000/0xc000 0xcc000/0x800 > cpu0 at mainbus0: (uniprocessor) > pci0 at mainbus0 bus 0: configuration mode 1 (bios) > pchb0 at pci0 dev 0 function 0 "Intel 82810 Host" rev 0x03 > vga1 at pci0 dev 1 function 0 "Intel 82810 Video" rev 0x03 > wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation) > wsdisplay0: screen 1-5 added (80x25, vt100 emulation) > intagp0 at vga1 > agp0 at intagp0: aperture at 0xf8000000, size 0x4000000 > ppb0 at pci0 dev 30 function 0 "Intel 82801AA Hub-to-PCI" rev 0x02 > pci1 at ppb0 bus 1 > xl0 at pci1 dev 8 function 0 "3Com 3c905C 100Base-TX" rev 0x30: irq > 11, address 00:01:03:e8:38:4b > ukphy0 at xl0 phy 24: Generic IEEE 802.3u media interface, rev. 0: OUI > 0x00601d, model 0x0035 > xl1 at pci1 dev 9 function 0 "3Com 3c905 100Base-TX" rev 0x00: irq 10, > address 00:60:97:be:ca:2a > nsphy0 at xl1 phy 24: DP83840 10/100 PHY, rev. 1 > ichpcib0 at pci0 dev 31 function 0 "Intel 82801AA LPC" rev 0x02: > 24-bit timer at 3579545Hz > pciide0 at pci0 dev 31 function 1 "Intel 82801AA IDE" rev 0x02: DMA, > channel 0 wired to compatibility, channel 1 wired to compatibility > wd0 at pciide0 channel 0 drive 0: <QUANTUM FIREBALLlct20 10> > wd0: 8-sector PIO, LBA, 9787MB, 20044080 sectors > wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 2 > atapiscsi0 at pciide0 channel 1 drive 1 > scsibus0 at atapiscsi0: 2 targets > cd0 at scsibus0 targ 0 lun 0: <HP, CD-Writer+ 7500, 1.0a> ATAPI > 5/cdrom removable > cd0(pciide0:1:1): using PIO mode 4, DMA mode 2 > uhci0 at pci0 dev 31 function 2 "Intel 82801AA USB" rev 0x02: irq 9 > ichiic0 at pci0 dev 31 function 3 "Intel 82801AA SMBus" rev 0x02: irq 10 > iic0 at ichiic0 > spdmem0 at iic0 addr 0x50: 128MB SDRAM non-parity PC133CL3 > spdmem1 at iic0 addr 0x51: 64MB SDRAM non-parity PC100CL2 > isa0 at ichpcib0 > isadma0 at isa0 > com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo > pckbc0 at isa0 port 0x60/5 > pckbd0 at pckbc0 (kbd slot) > pckbc0: using irq 1 for kbd slot > wskbd0 at pckbd0: console keyboard, using wsdisplay0 > pcppi0 at isa0 port 0x61 > spkr0 at pcppi0 > lpt0 at isa0 port 0x378/4 irq 7 > npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16 > fdc0 at isa0 port 0x3f0/6 irq 6 drq 2 > usb0 at uhci0: USB revision 1.0 > uhub0 at usb0 "Intel UHCI root hub" rev 1.00/1.00 addr 1 > biomask f76d netmask ff6d ttymask ffff > mtrr: Pentium Pro MTRR support > softraid0 at root > root on wd0a swap on wd0b dump on wd0b > syncing disks... done > rebooting... > OpenBSD 4.8 (GENERIC) #136: Mon Aug 16 09:06:23 MDT 2010 > [email protected]:/usr/src/sys/arch/i386/compile/GENERIC > cpu0: Intel Pentium III ("GenuineIntel" 686-class, 128KB L2 cache) 632 MHz > cpu0: > FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PSE36,MMX,FXSR,SSE > real mem = 199585792 (190MB) > avail mem = 186396672 (177MB) > mainbus0 at root > bios0 at mainbus0: AT/286+ BIOS, date 03/07/01, BIOS32 rev. 0 @ > 0xfda74, SMBIOS rev. 2.3 @ 0xf0ea0 (55 entries) > bios0: vendor Intel Corp. version "A11" date 03/07/2001 > bios0: Dell Computer Corporation L800C > apm0 at bios0: Power Management spec V1.2 > apm0: AC on, battery charge unknown > acpi at bios0 function 0x0 not configured > pcibios0 at bios0: rev 2.1 @ 0xf0000/0x10000 > pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xf2f30/192 (10 entries) > pcibios0: PCI Interrupt Router at 000:31:0 ("Intel 82371FB ISA" rev 0x00) > pcibios0: PCI bus #1 is the last bus > bios0: ROM list: 0xc0000/0xc000 0xcc000/0x800 > cpu0 at mainbus0: (uniprocessor) > pci0 at mainbus0 bus 0: configuration mode 1 (bios) > pchb0 at pci0 dev 0 function 0 "Intel 82810 Host" rev 0x03 > vga1 at pci0 dev 1 function 0 "Intel 82810 Video" rev 0x03 > wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation) > wsdisplay0: screen 1-5 added (80x25, vt100 emulation) > intagp0 at vga1 > agp0 at intagp0: aperture at 0xf8000000, size 0x4000000 > ppb0 at pci0 dev 30 function 0 "Intel 82801AA Hub-to-PCI" rev 0x02 > pci1 at ppb0 bus 1 > xl0 at pci1 dev 8 function 0 "3Com 3c905C 100Base-TX" rev 0x30: irq > 11, address 00:01:03:e8:38:4b > ukphy0 at xl0 phy 24: Generic IEEE 802.3u media interface, rev. 0: OUI > 0x00601d, model 0x0035 > xl1 at pci1 dev 9 function 0 "3Com 3c905 100Base-TX" rev 0x00: irq 10, > address 00:60:97:be:ca:2a > nsphy0 at xl1 phy 24: DP83840 10/100 PHY, rev. 1 > ichpcib0 at pci0 dev 31 function 0 "Intel 82801AA LPC" rev 0x02: > 24-bit timer at 3579545Hz > pciide0 at pci0 dev 31 function 1 "Intel 82801AA IDE" rev 0x02: DMA, > channel 0 wired to compatibility, channel 1 wired to compatibility > wd0 at pciide0 channel 0 drive 0: <QUANTUM FIREBALLlct20 10> > wd0: 8-sector PIO, LBA, 9787MB, 20044080 sectors > wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 2 > atapiscsi0 at pciide0 channel 1 drive 1 > scsibus0 at atapiscsi0: 2 targets > cd0 at scsibus0 targ 0 lun 0: <HP, CD-Writer+ 7500, 1.0a> ATAPI > 5/cdrom removable > cd0(pciide0:1:1): using PIO mode 4, DMA mode 2 > uhci0 at pci0 dev 31 function 2 "Intel 82801AA USB" rev 0x02: irq 9 > ichiic0 at pci0 dev 31 function 3 "Intel 82801AA SMBus" rev 0x02: irq 10 > iic0 at ichiic0 > spdmem0 at iic0 addr 0x50: 128MB SDRAM non-parity PC133CL3 > spdmem1 at iic0 addr 0x51: 64MB SDRAM non-parity PC100CL2 > isa0 at ichpcib0 > isadma0 at isa0 > com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo > pckbc0 at isa0 port 0x60/5 > pckbd0 at pckbc0 (kbd slot) > pckbc0: using irq 1 for kbd slot > wskbd0 at pckbd0: console keyboard, using wsdisplay0 > pcppi0 at isa0 port 0x61 > spkr0 at pcppi0 > lpt0 at isa0 port 0x378/4 irq 7 > npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16 > fdc0 at isa0 port 0x3f0/6 irq 6 drq 2 > usb0 at uhci0: USB revision 1.0 > uhub0 at usb0 "Intel UHCI root hub" rev 1.00/1.00 addr 1 > biomask f76d netmask ff6d ttymask ffff > mtrr: Pentium Pro MTRR support > softraid0 at root > root on wd0a swap on wd0b dump on wd0b > > > ***********netstat_rnf_inet**************** > > Routing tables > > Internet: > Destination Gateway Flags Refs Use Mtu Prio > Iface > default 192.168.1.1 UGS 0 359 - 8 xl0 > 127/8 127.0.0.1 UGRS 0 0 33200 8 lo0 > 127.0.0.1 127.0.0.1 UH 2 352 33200 4 lo0 > 192.168.0/24 link#2 C 2 0 - 4 xl1 > 192.168.0.1 00:60:97:be:ca:2a HLc 0 6 - 4 lo0 > 192.168.0.10 link#2 HLc 1 19 - 4 xl1 > 192.168.1/24 link#1 UC 1 0 - 4 xl0 > 192.168.1.1 00:1d:0f:fc:95:de UHLc 2 10 - 4 xl0 > 192.168.1.101 127.0.0.1 UGHS 2 24 33200 8 lo0 > 224/4 127.0.0.1 URS 0 0 33200 8 lo0 > > > ********* ping_cliente ******************** > > --- 192.168.0.10 ping statistics --- > 3 packets transmitted, 0 packets received, 100.0% packet loss > > > > ************** rc ********************* > !/bin/sh - > # > # $OpenBSD: rc.conf,v 1.139 2010/07/29 13:55:48 jmc Exp $ > > # set these to "NO" to turn them off. otherwise, they're used as flags > ldpd_flags=NO # for normal use: "" > ripd_flags=NO # for normal use: "" > mrouted_flags=NO # for normal use: "", if activated > # be sure to enable multicast_router below. > dvmrpd_flags=NO # for normal use: "" > ospfd_flags=NO # for normal use: "" > ospf6d_flags=NO # for normal use: "" > bgpd_flags=NO # for normal use: "" > rarpd_flags=NO # for normal use: "-a" > bootparamd_flags=NO # for normal use: "" > rbootd_flags=NO # for normal use: "" > sshd_flags="" # for normal use: "" > named_flags="" # for normal use: "" > rdate_flags=NO # for normal use: [RFC868-host] or [-n > RFC2030-host] > timed_flags=NO # for normal use: "" > ldattach_flags=NO # for normal use: "[options] linedisc cua-device" > ntpd_flags=NO # for normal use: "" > isakmpd_flags=NO # for normal use: "" > iked_flags=NO # for normal use: "" > sasyncd_flags=NO # for normal use: "" > mopd_flags=NO # for normal use: "-a" > apmd_flags=NO # for normal use: "" > dhcpd_flags=NO # for normal use: "" > dhcrelay_flags=NO # for normal use: "-i interface [server]" > rtadvd_flags=NO # for normal use: list of interfaces > # be sure to set net.inet6.ip6.forwarding=1 > route6d_flags=NO # for normal use: "" > # be sure to set net.inet6.ip6.forwarding=1 > rtsold_flags=NO # for normal use: interface > # be sure to set net.inet6.ip6.forwarding=0 > # be sure to set net.inet6.ip6.accept_rtadv=1 > lpd_flags=NO # for normal use: "" (or "-l" for debugging) > sensorsd_flags=NO # for normal use: "" > hotplugd_flags=NO # for normal use: "" > watchdogd_flags=NO # for normal use: "" > ftpproxy_flags=NO # for normal use: "" > hostapd_flags=NO # for normal use: "" > ifstated_flags=NO # for normal use: "" > relayd_flags=NO # for normal use: "" > snmpd_flags=NO # for normal use: "" > smtpd_flags=NO # for normal use: "" > aucat_flags=NO # for normal use: "" > ldapd_flags=NO # for normal use: "" > > # use -u to disable chroot, see httpd(8) > httpd_flags=NO # for normal use: "" (or "-DSSL" after reading > ssl(8)) > > # For normal use: "-L sm-mta -bd -q30m", and note there is a cron job > sendmail_flags="-L sm-mta -C/etc/mail/localhost.cf -bd -q30m" > spamd_flags=NO # for normal use: "" and see spamd(8) > spamd_black=NO # set to YES to run spamd without greylisting > spamlogd_flags="" # use eg. "-i interface" and see spamlogd(8) > > # Set to NO if ftpd is running out of inetd > ftpd_flags=NO # for non-inetd use: "-D" > > # Set to NO if identd is running out of inetd > identd_flags=NO # for non-inetd use: "-b -elo" > > # On some architectures, you must also disable console getty in /etc/ttys > xdm_flags=NO # for normal use: "" > > # For enabling console mouse support (i386 alpha amd64) > wsmoused_flags=NO # for ps/2 or usb mice: "", serial: "-p /dev/cua00" > > # set the following to "YES" to turn them on > rwhod=NO > nfs_server=NO # see sysctl.conf for nfs client configuration > lockd=NO > amd=NO > pf=YES # Packet filter / NAT > ipsec=NO # IPsec > bt=NO # Bluetooth > portmap=NO # Note: inetd(8) rpc services need portmap too > inetd=YES # almost always needed > check_quotas=YES # NO may be desirable in some YP environments > accounting=NO # process accounting (using /var/account/acct) > > krb5_master_kdc=NO # KerberosV master KDC. Run 'info heimdal' for help. > krb5_slave_kdc=NO # KerberosV slave KDC. > afs=NO # mount and run afs > > # Multicast routing configuration > # Please look at netstart(8) for a detailed description if you change these > multicast_host=NO # Route all multicast packets to a single interface > multicast_router=NO # A multicast routing daemon will be run, e.g. mrouted > > # miscellaneous other flags > # only used if the appropriate server is marked YES above > savecore_flags= # "-z" to compress > ypserv_flags= # E.g. -1 for YP v1, -d for DNS etc > yppasswdd_flags=NO # "-d /etc/yp" if passwd files are in /etc/yp > nfsd_flags="-tun 4" # Crank the 4 for a busy NFS fileserver > amd_master=/etc/amd/master # AMD 'master' map > syslogd_flags= # add more flags, e.g. "-u -a > /chroot/dev/log" > pf_rules=/etc/pf.conf # Packet filter rules file > ipsec_rules=/etc/ipsec.conf # IPsec rules file > bt_rules=/etc/bt.conf # Bluetooth rules file > pflogd_flags= # add more flags, e.g. "-s 256" > afsd_flags= # Flags passed to afsd > shlib_dirs= # extra directories for ldconfig, separated > # by space > > local_rcconf="/etc/rc.conf.local" > > [ -f ${local_rcconf} ] && . ${local_rcconf} # Do not edit this line > > > > > > **************** sysctl ************************** > > > # $OpenBSD: sysctl.conf,v 1.47 2009/06/09 11:52:54 sthen Exp $ > # > # This file contains a list of sysctl options the user wants set at > # boot time. See sysctl(3) and sysctl(8) for more information on > # the many available variables. > # > net.inet.ip.forwarding=1 # 1=Permit forwarding (routing) of IPv4 packets > #net.inet.ip.mforwarding=1 # 1=Permit forwarding (routing) of IPv4 > multicast packets > #net.inet.ip.multipath=1 # 1=Enable IP multipath routing > #net.inet.icmp.rediraccept=1 # 1=Accept ICMP redirects > #net.inet6.icmp6.rediraccept=0 # 0=Don't accept IPv6 ICMP redirects > #net.inet6.ip6.forwarding=1 # 1=Permit forwarding (routing) of IPv6 packets > #net.inet6.ip6.mforwarding=1 # 1=Permit forwarding (routing) of IPv6 > multicast packets > #net.inet6.ip6.multipath=1 # 1=Enable IPv6 multipath routing > #net.inet6.ip6.accept_rtadv=1 # 1=Permit IPv6 autoconf (forwarding must be > 0) > #net.inet.tcp.rfc1323=0 # 0=Disable TCP RFC1323 extensions (for > if tcp is > slow) > #net.inet.tcp.rfc3390=0 # 0=Disable RFC3390 for TCP window > increasing > #net.inet.esp.enable=0 # 0=Disable the ESP IPsec protocol > #net.inet.ah.enable=0 # 0=Disable the AH IPsec protocol > #net.inet.esp.udpencap=0 # 0=Disable ESP-in-UDP encapsulation > #net.inet.ipcomp.enable=1 # 1=Enable the IPCOMP protocol > #net.inet.etherip.allow=1 # 1=Enable the Ethernet-over-IP protocol > #net.inet.tcp.ecn=1 # 1=Enable the TCP ECN extension > #net.inet.carp.preempt=1 # 1=Enable carp(4) preemption > #net.inet.carp.log=1 # 1=Enable logging of carp(4) packets > #ddb.panic=0 # 0=Do not drop into ddb on a kernel panic > #ddb.console=1 # 1=Permit entry of ddb from the console > #fs.posix.setuid=0 # 0=Traditional BSD chown() semantics > #vm.swapencrypt.enable=0 # 0=Do not encrypt pages that go to swap > #vfs.nfs.iothreads=4 # Number of nfsio kernel threads > #net.inet.ip.mtudisc=0 # 0=Disable tcp mtu discovery > #kern.usercrypto=0 # 0=Disable userland use of /dev/crypto > #kern.splassert=2 # 2=Enable with verbose error messages > #kern.nosuidcoredump=2 # 2=Put suid coredumps in /var/crash > #kern.watchdog.period=32 # >0=Enable hardware watchdog(4) timer if > available > #kern.watchdog.auto=0 # 0=Disable automatic watchdog(4) retriggering > machdep.allowaperture=2 # See xf86(4) > #machdep.apmhalt=1 # 1=powerdown hack, try if halt -p doesn't work > #machdep.kbdreset=1 # permit console CTRL-ALT-DEL to do a nice halt > #machdep.lidsuspend=1 # laptop lid closes cause a suspend > #machdep.userldt=1 # allow userland programs to play with ldt, > # required by some ports > #kern.emul.aout=1 # enable running dynamic OpenBSD a.out bins > #kern.emul.freebsd=1 # enable running FreeBSD binaries > #kern.emul.linux=1 # enable running Linux binaries > #kern.emul.svr4=1 # enable running SVR4 binaries > > > > ********* ping_wwwopenbsd ******************* > > PING www.openbsd.org (142.244.12.42): 56 data bytes > 64 bytes from 142.244.12.42: icmp_seq=0 ttl=233 time=174.725 ms > 64 bytes from 142.244.12.42: icmp_seq=1 ttl=233 time=173.004 ms > 64 bytes from 142.244.12.42: icmp_seq=2 ttl=233 time=173.861 ms > > > > --- www.openbsd.org ping statistics --- > 3 packets transmitted, 3 packets received, 0.0% packet loss > round-trip min/avg/max/std-dev = 173.004/173.863/174.725/0.780 ms > > > > ****************pfctl_sa******************** > > FILTER RULES: > match out on egress inet from ! (egress:network) to any nat-to > (egress:0) round-robin > block return in log all > pass out quick all flags S/SA keep state > pass in inet proto icmp all icmp-type echoreq keep state > pass in on xl1 all flags S/SA keep state > block return in on ! lo0 proto tcp from any to any port 6000:6010 > No queue in use > > INFO: > Status: Enabled for 0 days 00:50:59 Debug: err > > Interface Stats for xl0 IPv4 IPv6 > Bytes In 301818 0 > Bytes Out 18342 64 > Packets In > Passed 290 0 > Blocked 6 0 > Packets Out > Passed 253 1 > Blocked 0 0 > > State Table Total Rate > current entries 0 > searches 570 0.2/s > inserts 52 0.0/s > removals 52 0.0/s > Counters > match 58 0.0/s > bad-offset 0 0.0/s > fragment 0 0.0/s > short 0 0.0/s > normalize 0 0.0/s > memory 0 0.0/s > bad-timestamp 0 0.0/s > congestion 0 0.0/s > ip-option 0 0.0/s > proto-cksum 0 0.0/s > state-mismatch 0 0.0/s > state-insert 0 0.0/s > state-limit 0 0.0/s > src-limit 0 0.0/s > synproxy 0 0.0/s > > TIMEOUTS: > tcp.first 120s > tcp.opening 30s > tcp.established 86400s > tcp.closing 900s > tcp.finwait 45s > tcp.closed 90s > tcp.tsdiff 30s > udp.first 60s > udp.single 30s > udp.multiple 60s > icmp.first 20s > icmp.error 10s > other.first 60s > other.single 30s > other.multiple 60s > frag 30s > interval 10s > adaptive.start 6000 states > adaptive.end 12000 states > src.track 0s > > LIMITS: > states hard limit 10000 > src-nodes hard limit 10000 > frags hard limit 5000 > tables hard limit 1000 > table-entries hard limit 200000 > > TABLES: > > OS FINGERPRINTS: > 696 fingerprints loaded > > > > ************* dhcpd ************** > > # $OpenBSD: dhcpd.conf,v 1.2 2008/10/03 11:41:21 sthen Exp $ > # > # DHCP server options. > # See dhcpd.conf(5) and dhcpd(8) for more information. > # > > # Network: 192.168.1.0/255.255.255.0 > # Domain name: my.domain > # Name servers: 192.168.1.3 and 192.168.1.5 > # Default router: 192.168.1.1 > # Addresses: 192.168.1.32 - 192.168.1.127 > # > option domain-name "my.domain"; > option domain-name-servers 192.168.1.3, 192.168.1.5; > > subnet 192.168.1.0 netmask 255.255.255.0 { > option routers 192.168.1.1; > > range 192.168.1.32 192.168.1.127; > > host static-client { > hardware ethernet 22:33:44:55:66:77; > fixed-address 192.168.1.200; > } > > host pxe-client { > hardware ethernet 02:03:04:05:06:07; > filename "pxeboot"; > next-server 192.168.1.1; > } > } > > > *********************** var_log_messages ********************** > > Dec 1 00:31:29 gateway /bsd: softraid0 at root > Dec 1 00:31:29 gateway /bsd: root on wd0a swap on wd0b dump on wd0b > Dec 1 00:31:29 gateway named[21877]: starting BIND 9.4.2-P2 > Dec 1 00:31:30 gateway named[21877]: command channel listening on > 127.0.0.1#953 > Dec 1 00:31:30 gateway named[21877]: command channel listening on ::1#953 > Dec 1 00:31:30 gateway named[21877]: running > Dec 1 00:31:30 gateway savecore: no core dump > Dec 1 00:31:33 gateway dhcpd[21708]: Can't listen on xl1 - dhcpd.conf > has no subnet declaration for 192.168.0.1. > Dec 1 00:31:33 gateway dhcpd[21708]: No interfaces to listen on. > Dec 1 00:31:33 gateway dhcpd[21708]: exiting. > > > > ************ route_show ************************************* > > Routing tables > > Internet: > Destination Gateway Flags Refs Use Mtu Prio > Iface > default 192.168.1.1 UGS 0 261 - 8 xl0 > loopback localhost UGRS 0 0 33200 8 lo0 > localhost localhost UH 2 24 33200 4 lo0 > 192.168.0/24 link#2 C 2 0 - 4 xl1 > gateway 00:60:97:be:ca:2a HLc 0 6 - 4 lo0 > 192.168.0.10 link#2 HLc 1 19 - 4 xl1 > 192.168.1/24 link#1 UC 1 0 - 4 xl0 > 192.168.1.1 00:1d:0f:fc:95:de UHLc 1 9 - 4 xl0 > 192.168.1.101 localhost UGHS 2 24 33200 8 lo0 > BASE-ADDRESS.MCAST localhost URS 0 0 33200 8 lo0 > > Internet6: > Destination Gateway Flags Refs Use Mtu Prio > Iface > ::/104 localhost UGRS 0 0 - 8 lo0 > ::/96 localhost UGRS 0 0 - 8 lo0 > localhost localhost UH 14 0 33200 4 lo0 > ::127.0.0.0/104 localhost UGRS 0 0 - 8 lo0 > ::224.0.0.0/100 localhost UGRS 0 0 - 8 lo0 > ::255.0.0.0/104 localhost UGRS 0 0 - 8 lo0 > ::ffff:0.0.0.0/96 localhost UGRS 0 0 - 8 lo0 > 2002::/24 localhost UGRS 0 0 - 8 lo0 > 2002:7f00::/24 localhost UGRS 0 0 - 8 lo0 > 2002:e000::/20 localhost UGRS 0 0 - 8 lo0 > 2002:ff00::/24 localhost UGRS 0 0 - 8 lo0 > fe80::/10 localhost UGRS 0 0 - 8 lo0 > fe80::%xl0/64 link#1 UC 0 0 - 4 xl0 > fe80::201:3ff:fee8 00:01:03:e8:38:4b UHL 0 0 - 4 lo0 > fe80::%xl1/64 link#2 C 0 0 - 4 xl1 > fe80::260:97ff:feb 00:60:97:be:ca:2a HL 0 0 - 4 lo0 > fe80::%lo0/64 fe80::1%lo0 U 0 0 - 4 lo0 > fe80::1%lo0 link#4 UHL 0 0 - 4 lo0 > fec0::/10 localhost UGRS 0 0 - 8 lo0 > ff01::/16 localhost UGRS 0 0 - 8 lo0 > ff01::%xl0/32 link#1 UC 0 0 - 4 xl0 > ff01::%xl1/32 link#2 C 0 0 - 4 xl1 > ff01::%lo0/32 localhost UC 0 0 - 4 lo0 > ff02::/16 localhost UGRS 0 0 - 8 lo0 > ff02::%xl0/32 link#1 UC 0 0 - 4 xl0 > ff02::%xl1/32 link#2 C 0 0 - 4 xl1 > ff02::%lo0/32 localhost UC 0 0 - 4 lo0 > > > > *************** ping_router_exterior ***************** > > PING 192.168.1.1 (192.168.1.1): 56 data bytes > 64 bytes from 192.168.1.1: icmp_seq=0 ttl=64 time=1.006 ms > 64 bytes from 192.168.1.1: icmp_seq=1 ttl=64 time=0.773 ms > 64 bytes from 192.168.1.1: icmp_seq=2 ttl=64 time=0.729 ms > > --- 192.168.1.1 ping statistics --- > 3 packets transmitted, 3 packets received, 0.0% packet loss > round-trip min/avg/max/std-dev = 0.729/0.836/1.006/0.121 ms > > > > **************** pf ********************* > > # $OpenBSD: pf.conf,v 1.49 2009/09/17 06:39:03 jmc Exp $ > # > # See pf.conf(5) for syntax and examples. > # Remember to set net.inet.ip.forwarding=1 and/or > net.inet6.ip6.forwarding=1 > # in /etc/sysctl.conf if packets are to be forwarded between interfaces. > int="xl1" > set block-policy return > set loginterface xl0 > match out on egress inet from !(egress:network) to any nat-to (egress:0) > block in log > > set skip on lo > > # filter rules and anchor for ftp-proxy(8) > #anchor "ftp-proxy/*" > #pass in quick proto tcp to port ftp rdr-to 127.0.0.1 port 8021 > > # anchor for relayd(8) > #anchor "relayd/*" > > pass out quick # to establish keep-state > pass in inet proto icmp all icmp-type echoreq > pass in on $int > > # rules for spamd(8) > #table <spamd-white> persist > #table <nospamd> persist file "/etc/mail/nospamd" > #pass in on egress proto tcp from any to any port smtp \ > # rdr-to 127.0.0.1 port spamd > #pass in on egress proto tcp from <nospamd> to any port smtp > #pass in log on egress proto tcp from <spamd-white> to any port smtp > #pass out log on egress proto tcp to any port smtp > > > #block in quick from urpf-failed to any # use with care > > # By default, do not permit remote connections to X11 > block in on ! lo0 proto tcp to port 6000:6010 > > > > ***************************** ifconfig ***************************** > > > lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 33200 > priority: 0 > groups: lo > inet 127.0.0.1 netmask 0xff000000 > inet6 ::1 prefixlen 128 > inet6 fe80::1%lo0 prefixlen 64 scopeid 0x4 > xl0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500 > lladdr 00:01:03:e8:38:4b > priority: 0 > groups: egress > media: Ethernet autoselect (100baseTX full-duplex) > status: active > inet6 fe80::201:3ff:fee8:384b%xl0 prefixlen 64 scopeid 0x1 > inet 192.168.1.101 netmask 0xffffff00 broadcast 255.255.255.255 > xl1: flags=8a43<UP,BROADCAST,RUNNING,ALLMULTI,SIMPLEX,MULTICAST> mtu 1500 > lladdr 00:60:97:be:ca:2a > priority: 0 > media: Ethernet autoselect (none) > status: no carrier > inet 192.168.0.1 netmask 0xffffff00 broadcast 192.168.0.255 > inet6 fe80::260:97ff:febe:ca2a%xl1 prefixlen 64 scopeid 0x2 > enc0: flags=0<> > priority: 0 > groups: enc > status: active > pflog0: flags=141<UP,RUNNING,PROMISC> mtu 33200 > priority: 0 > groups: pflog > > > > *********************** ping_cliente ****************** > > > --- 192.168.0.10 ping statistics --- > 3 packets transmitted, 0 packets received, 100.0% packet loss > > ///////////////////////////////////////////////////////////////////////////////////////////////////////////////////// > //////////////////////////// INFORMATION CLIENTE > //////////////////////////////////////////////// > ///////////////////////////////////////////////////////////////////////////////////////////////////////////////////// > > ********** dmesg *********** > > > OpenBSD 4.7 (GENERIC) #558: Wed Mar 17 20:46:15 MDT 2010 > [email protected]:/usr/src/sys/arch/i386/compile/GENERIC > cpu0: Mobile AMD Athlon(tm) 4 processor ("AuthenticAMD" 686-class, > 256KB L2 cache) 1 GHz > cpu0: > FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE > real mem = 502820864 (479MB) > avail mem = 478490624 (456MB) > mainbus0 at root > bios0 at mainbus0: AT/286+ BIOS, date 01/16/04, BIOS32 rev. 0 @ > 0xfbc70, SMBIOS rev. 2.3 @ 0xf0800 (33 entries) > bios0: vendor Phoenix Technologies, LTD version "6.00 PG" date 01/16/2004 > bios0: MICRO-STAR INTERNATIONAL CO., LTD KM400-8235 > apm0 at bios0: Power Management spec V1.2 (slowidle) > apm0: AC on, battery charge unknown > acpi at bios0 function 0x0 not configured > pcibios0 at bios0: rev 2.1 @ 0xf0000/0xde94 > pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xfddf0/160 (8 entries) > pcibios0: PCI Exclusive IRQs: 5 10 11 > pcibios0: PCI Interrupt Router at 000:17:0 ("VIA VT82C596A ISA" rev 0x00) > pcibios0: PCI bus #1 is the last bus > bios0: ROM list: 0xc0000/0x7e00 > cpu0 at mainbus0: (uniprocessor) > pci0 at mainbus0 bus 0: configuration mode 1 (bios) > pchb0 at pci0 dev 0 function 0 "VIA VT8378 PCI" rev 0x00 > viaagp0 at pchb0: v3 > agp0 at viaagp0: aperture at 0xd0000000, size 0x10000000 > ppb0 at pci0 dev 1 function 0 "VIA VT8377 AGP" rev 0x00 > pci1 at ppb0 bus 1 > vga1 at pci1 dev 0 function 0 "VIA VT8378 VGA" rev 0x01 > wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation) > wsdisplay0: screen 1-5 added (80x25, vt100 emulation) > uhci0 at pci0 dev 16 function 0 "VIA VT83C572 USB" rev 0x80: irq 11 > uhci1 at pci0 dev 16 function 1 "VIA VT83C572 USB" rev 0x80: irq 11 > uhci2 at pci0 dev 16 function 2 "VIA VT83C572 USB" rev 0x80: irq 10 > ehci0 at pci0 dev 16 function 3 "VIA VT6202 USB" rev 0x82: irq 5 > usb0 at ehci0: USB revision 2.0 > uhub0 at usb0 "VIA EHCI root hub" rev 2.00/1.00 addr 1 > viapm0 at pci0 dev 17 function 0 "VIA VT8235 ISA" rev 0x00 > iic0 at viapm0 > iic0: addr 0x2f 04=00 06=03 07=00 0c=00 0d=07 0e=85 0f=00 10=c4 11=10 > 12=00 13=60 14=14 15=62 16=01 17=06 words 00=ffff 01=ffff 02=ffff > 03=ffff 04=00ff 05=ffff 06=03ff 07=00ff > spdmem0 at iic0 addr 0x50: 256MB DDR SDRAM non-parity PC2700CL2.5 > spdmem1 at iic0 addr 0x51: 256MB DDR SDRAM non-parity PC3200CL3.0 > pciide0 at pci0 dev 17 function 1 "VIA VT82C571 IDE" rev 0x06: ATA133, > channel 0 configured to compatibility, channel 1 configured to > compatibility > wd0 at pciide0 channel 0 drive 0: <Maxtor 2B020H1> > wd0: 16-sector PIO, LBA48, 19541MB, 40020624 sectors > wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 5 > pciide0: channel 1 disabled (no drives) > auvia0 at pci0 dev 17 function 5 "VIA VT8233 AC97" rev 0x50: irq 10 > ac97: codec id 0x414c4760 (Avance Logic ALC655 rev 0) > audio0 at auvia0 > vr0 at pci0 dev 18 function 0 "VIA RhineII-2" rev 0x74: irq 11, > address 00:0c:76:bb:00:5a > ukphy0 at vr0 phy 1: Generic IEEE 802.3u media interface, rev. 8: OUI > 0x004063, model 0x0032 > usb1 at uhci0: USB revision 1.0 > uhub1 at usb1 "VIA UHCI root hub" rev 1.00/1.00 addr 1 > usb2 at uhci1: USB revision 1.0 > uhub2 at usb2 "VIA UHCI root hub" rev 1.00/1.00 addr 1 > usb3 at uhci2: USB revision 1.0 > uhub3 at usb3 "VIA UHCI root hub" rev 1.00/1.00 addr 1 > isa0 at mainbus0 > isadma0 at isa0 > com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo > pckbc0 at isa0 port 0x60/5 > pckbd0 at pckbc0 (kbd slot) > pckbc0: using irq 1 for kbd slot > wskbd0 at pckbd0: console keyboard, using wsdisplay0 > pms0 at pckbc0 (aux slot) > pckbc0: using irq 12 for aux slot > wsmouse0 at pms0 mux 0 > pcppi0 at isa0 port 0x61 > midi0 at pcppi0: <PC speaker> > spkr0 at pcppi0 > lpt0 at isa0 port 0x378/4 irq 7 > wbsio0 at isa0 port 0x2e/2: W83697HF rev 0x12 > lm1 at wbsio0 port 0x290/8: W83697HF > npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16 > fdc0 at isa0 port 0x3f0/6 irq 6 drq 2 > biomask ef6d netmask ef6d ttymask ffff > mtrr: Pentium Pro MTRR support > vscsi0 at root > scsibus0 at vscsi0: 256 targets > softraid0 at root > root on wd0a swap on wd0b dump on wd0b > > > > *********ifconfig ****************** > > lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 33200 > priority: 0 > groups: lo > inet 127.0.0.1 netmask 0xff000000 > inet6 ::1 prefixlen 128 > inet6 fe80::1%lo0 prefixlen 64 scopeid 0x3 > vr0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500 > lladdr 00:0c:76:bb:00:5a > priority: 0 > groups: egress > media: Ethernet autoselect (none) > status: no carrier > inet 192.168.0.10 netmask 0xffffff00 broadcast 192.168.0.255 > inet6 fe80::20c:76ff:febb:5a%vr0 prefixlen 64 scopeid 0x1 > enc0: flags=0<> mtu 1536 > priority: 0 > > > > > *************** netstat_rn ************* > > Routing tables > > Internet: > Destination Gateway Flags Refs Use Mtu Prio > Iface > default 192.168.0.1 GS 0 32 - 8 vr0 > 127/8 127.0.0.1 UGRS 0 0 33200 8 lo0 > 127.0.0.1 127.0.0.1 UH 1 360 33200 4 lo0 > 192.168.0/24 link#1 C 1 0 - 4 vr0 > 192.168.0.1 link#1 HLc 1 0 - 4 vr0 > 224/4 127.0.0.1 URS 0 0 33200 8 lo0 > > Internet6: > Destination Gateway > Flags Refs Use Mtu Prio Iface > ::/104 ::1 UGRS > 0 0 - 8 lo0 > ::/96 ::1 UGRS > 0 0 - 8 lo0 > ::1 ::1 UH > 14 0 33200 4 lo0 > ::127.0.0.0/104 ::1 UGRS > 0 0 - 8 lo0 > ::224.0.0.0/100 ::1 UGRS > 0 0 - 8 lo0 > ::255.0.0.0/104 ::1 UGRS > 0 0 - 8 lo0 > ::ffff:0.0.0.0/96 ::1 UGRS > 0 0 - 8 lo0 > 2002::/24 ::1 UGRS > 0 0 - 8 lo0 > 2002:7f00::/24 ::1 UGRS > 0 0 - 8 lo0 > 2002:e000::/20 ::1 UGRS > 0 0 - 8 lo0 > 2002:ff00::/24 ::1 UGRS > 0 0 - 8 lo0 > fe80::/10 ::1 UGRS > 0 0 - 8 lo0 > fe80::%vr0/64 link#1 C > 0 0 - 4 vr0 > fe80::20c:76ff:febb:5a%vr0 00:0c:76:bb:00:5a HL > 0 0 - 4 lo0 > fe80::%lo0/64 fe80::1%lo0 U > 0 0 - 4 lo0 > fe80::1%lo0 link#3 UHL > 0 0 - 4 lo0 > fec0::/10 ::1 UGRS > 0 0 - 8 lo0 > ff01::/16 ::1 UGRS > 0 0 - 8 lo0 > ff01::%vr0/32 link#1 C > 0 0 - 4 vr0 > ff01::%lo0/32 ::1 UC > 0 0 - 4 lo0 > ff02::/16 ::1 UGRS > 0 0 - 8 lo0 > ff02::%vr0/32 link#1 C > 0 0 - 4 vr0 > ff02::%lo0/32 ::1 UC > 0 0 - 4 lo0 > > > > ***********ping_gateway************* > > --- 192.168.0.1 ping statistics --- > 3 packets transmitted, 0 packets received, 100.0% packet loss > > > > ****************ping_router_exterior**************** > > --- 192.168.1.1 ping statistics --- > 3 packets transmitted, 0 packets received, 100.0% packet loss > > > > ********************route********************** > Routing tables > > Internet: > Destination Gateway Flags Refs Use Mtu Prio > Iface > default 192.168.1.1 GS 0 0 - 8 vr0 > loopback localhost UGRS 0 0 33200 8 lo0 > localhost localhost UH 1 0 33200 4 lo0 > 192.168.1/24 link#1 C 2 0 - 4 vr0 > 192.168.1.1 link#1 HLc 1 0 - 4 vr0 > 192.168.1.200 link#1 HLc 0 0 - 4 vr0 > BASE-ADDRESS.MCAST localhost URS 0 0 33200 8 lo0 > > Internet6: > Destination Gateway Flags Refs Use Mtu Prio > Iface > ::/104 localhost UGRS 0 0 - 8 lo0 > ::/96 localhost UGRS 0 0 - 8 lo0 > localhost localhost UH 14 0 33200 4 lo0 > ::127.0.0.0/104 localhost UGRS 0 0 - 8 lo0 > ::224.0.0.0/100 localhost UGRS 0 0 - 8 lo0 > ::255.0.0.0/104 localhost UGRS 0 0 - 8 lo0 > ::ffff:0.0.0.0/96 localhost UGRS 0 0 - 8 lo0 > 2002::/24 localhost UGRS 0 0 - 8 lo0 > 2002:7f00::/24 localhost UGRS 0 0 - 8 lo0 > 2002:e000::/20 localhost UGRS 0 0 - 8 lo0 > 2002:ff00::/24 localhost UGRS 0 0 - 8 lo0 > fe80::/10 localhost UGRS 0 0 - 8 lo0 > fe80::%vr0/64 link#1 C 0 0 - 4 vr0 > fe80::20c:76ff:feb 00:0c:76:bb:00:5a HL 0 0 - 4 lo0 > fe80::%lo0/64 fe80::1%lo0 U 0 0 - 4 lo0 > fe80::1%lo0 link#3 UHL 0 0 - 4 lo0 > fec0::/10 localhost UGRS 0 0 - 8 lo0 > ff01::/16 localhost UGRS 0 0 - 8 lo0 > ff01::%vr0/32 link#1 C 0 0 - 4 vr0 > ff01::%lo0/32 localhost UC 0 0 - 4 lo0 > ff02::/16 localhost UGRS 0 0 - 8 lo0 > ff02::%vr0/32 link#1 C 0 0 - 4 vr0 > ff02::%lo0/32 localhost UC 0 0 - 4 lo0
