There are some pulse counts on the syncinjectors which may help you
troubleshoot. Pulses used should go up by one every second, no more, no
less. None of the other counters should increment except very rarely.
If you're seeing anything else, shoot a couple of screenshots into
cust...@packetflux.com
On Mar 2, 2015 1:50 PM, "George Skorup (Cyber Broadcasting)" <
geo...@cbcast.com> wrote:
> Yes, there are issues I'm seeing with AutoSync on all bands with 13.2/
> 13.2.1. But 3GHz is... different, and I don't know why. I have a couple
> APs on a SyncInjector and some single APs on parasitic pipes. I thought it
> was just the SyncInjector or something else at the site until I started
> seeing the same problems on the parasitics after just a few days of install
> at new sites. They all have the on-board GPS disabled too. Random LBT hits,
> the APs show inSync and outSync counts but no lost/acquired timing messages
> in the event log, and the SyncInjector says nothing happened, SMs going
> crazy losing session, APs reporting SMs out of range when things go nuts
> and I have to reboot the AP(s). AutoSync+FreeRun get stuck in FreeRun.
> Something in the FPGA code or some other logic screwed up. I have no idea,
> so I hope Cambium can figure it out.
>
> On 3/2/2015 12:25 PM, Bill Prince wrote:
>
>> Not this one. This one is running a pair of PMP450s in 5 GHz.
>>
>> We're putting up a pair of PMP450s soon on different POPs; one will go
>> into a syncinjector, the other will be a CTM.
>>
>> Is there some issue that you're seeing on the 3GHz varaiety?
>>
>>
>> bp
>> <part15sbs{at}gmail{dot}com>
>>
>> On 3/2/2015 10:06 AM, George Skorup (Cyber Broadcasting) wrote:
>>
>>> Doesn't matter. The RJ45's are just pass-thru. The new universal pipes
>>> pull power from two pins, so it can be used with either PMP100/450 or 430
>>> APs. But I always have the guys put the jumper out to the radio into the
>>> center RJ45 and the cable from the injector to the RJ45 with the LEDs, just
>>> as standard practice, not that it matters.
>>>
>>> I do have a question for you about this though.. is this SyncInjector
>>> running 3GHz 450 APs?
>>>
>>> On 3/2/2015 11:55 AM, Bill Prince wrote:
>>>
>>>> Thanks George!
>>>>
>>>> i take it from the description that this boogers up the power/outputs
>>>> such that (ether?) RJ45 on the parasitic can be used to connect to the
>>>> syncinjector? One of the RJ45s has lights, and the other is just a vanilla
>>>> shielded RJ45 (I'm looking at a rev H1). So I can just build this little
>>>> jumper for between the 6p6c and the adjacent RJ45, then use the outer RJ45
>>>> to connect to the syncinjector?
>>>>
>>>> bp
>>>> <part15sbs{at}gmail{dot}com>
>>>>
>>>> On 3/2/2015 9:44 AM, George Skorup (Cyber Broadcasting) wrote:
>>>>
>>>>> Yes. http://manuals.packetflux.com/index.php?page=using-a-
>>>>> syncpipe-parasitic-with-a-syncinjector
>>>>>
>>>>> On 3/2/2015 11:25 AM, Bill Prince wrote:
>>>>>
>>>>>>
>>>>>> We have a syncpipe basic that we think is starting to act up. It
>>>>>> seems to lose sync about once every day or two for about 1 second. It's
>>>>>> starting to raise havoc with long-lasting client sessions through the
>>>>>> affected APs.
>>>>>>
>>>>>> We only have a couple of syncpipe parasitics in stock; can one of
>>>>>> these be swapped in place of a basic to run a sync injector?
>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>
>>>>
>>>
>>
>
