Close.

https://www.youtube.com/watch?v=JNPW2wZ4D2s

On 2/28/2016 8:25 PM, Ken Hohhof wrote:
Mmmm, pistol whip.
https://www.youtube.com/watch?v=fH185Hn38m8
OK, I’m guessing that wasn’t what you had in mind?
*From:* George Skorup <mailto:[email protected]>
*Sent:* Sunday, February 28, 2016 8:11 PM
*To:* [email protected] <mailto:[email protected]>
*Subject:* Re: [AFMUG] Mikrotik OSPF route selection oddness
I think you said it best...

"sometimes RouterOS rides the short bus"

You'd really need to look at the LSA table, OSPF route table and the system routing table to figure out what was really going on.

The thing that used to drive me insane was a BGP session going down would withdraw that LSA as expected, but the routers using that wouldn't inject ANY other default route in their routing table, even though they existed in the LSA and OSPF route lists. I'd have to bounce an interface so that SPF would recalculate and reconverge the entire network. I thought I had something configured wrong for the longest time. No, just RouterOS shenanigans. It needed a pistol whip. (if anyone gets that reference, +1 to you)

On 2/28/2016 7:48 PM, Adam Moffett wrote:
The two routers saw each other as neighbors.
I did not look closely at the LSA....but why would OSPF routes not get injected into the routing table?

On 2/28/2016 2:48 PM, George Skorup wrote:
That would be my question too. Were the adjacencies up full at the time and not stuck in 2-way or something like that? If they were full but no traffic, my money would be on OSPF routes simply not getting injected into the routing table.

Pretty much all of my OSPF issues went away after moving from 5.25/26 to 6.32.2. However, I did have a similar situation a week or so ago. No traffic across a link for several hours. And the link was definitely up. It happened in the middle of the night, so I didn't get a chance to see what was going on. It just fixed itself. But the routers showed no adjacency loss. So I have no idea.

On 2/28/2016 10:50 AM, Darin Steffl wrote:
Have you checked to see if there is still an OSPF connection running over this licensed link? As in do you see the neighbor router listed in OSPF for the other side of the link? On Sun, Feb 28, 2016 at 10:18 AM, Adam Moffett <[email protected]> wrote:

    I have a 500mbps licensed microwave path that was up and
    looking perfectly fine, but had no traffic on it.
    Instead traffic was moving on a 5.8 Radwin to a different site.
    Everything was up, but I don't understand this route
    selection.  The path via the Radwin is longer to lots of
    places, so OSPF should have used the licensed path for at least
    SOME traffic simply based on it being shorter. I also set the
    costs on the interfaces on both ends of that Radwin to 150, so
    it normally doesn't get used at all. Somehow this morning at
    3:15am the routers decided to use the backup path.  Everything
    returned to normal after I rebooted one end.

    It may be coincidental (or not), but I know a truck took out a
    telephone pole last night which caused an upstream fiber issue,
    and we had a UPS battery explode.  Is this all coincidence?
    Sometimes UPS's explode, sometimes That One Guy Steve burns
    down a house, sometimes RouterOS rides the short bus, some
    things are just outside our control.  Or maybe a truck hit a
    pole, which caused a power surge that blew up a UPS and made a
    Mikrotik fart inside of it's head.  I could believe either one.

    In any case.  Is there a different RouterOS version that will
trust my opinion when I tell it a path has high cost? Currently running 6.32.3 I think. It's pretty non-sensical
    that this happened at all.



--
Darin Steffl
Minnesota WiFi
www.mnwifi.com <http://www.mnwifi.com/>
507-634-WiFi
<http://www.facebook.com/minnesotawifi> Like us on Facebook <http://www.facebook.com/minnesotawifi>




Reply via email to