Uh oh. I figured it out. It was as I suspected. The SS is clamping due
to the sync pulse. Maybe the change that Forrest made with the Rev i0
SyncInjectors/PowerInjector+Sync because of the 450i's finicky handling
of the pulse over long runs? I have no idea. So much for GigE + sync
over power I guess. I don't have any Rev i0 Gigabit SyncInjectors to
test with, but I assume I'd get the same result.
I set the AP back to negotiate GigE. Turned off the sync on the injector
port feeding that radio. Rebooted the AP. Link stays up at gigabit with
no problems. Then I turned the sync pulse back on and the link dropped
almost instantly.
18:33:42 interface,info ether6 link down
18:33:49 interface,info ether6 link up (speed 1G, full duplex)
18:33:53 interface,info ether6 link down
18:33:55 interface,info ether6 link up (speed 1G, full duplex)
.... sync pulse back on
18:35:31 interface,info ether6 link down
18:35:34 interface,info ether6 link up (speed 1G, full duplex)
18:35:35 interface,info ether6 link down
18:35:42 interface,info ether6 link up (speed 1G, full duplex)
18:35:43 interface,info ether6 link down
18:35:46 interface,info ether6 link up (speed 1G, full duplex)
18:35:47 interface,info ether6 link down
18:35:52 interface,info ether6 link up (speed 100M, full duplex)
The GigE-APC's I have at this site are definitely HV's. That's all I
have ever ordered. They are all marked HV in sharpie on the handle. I'm
feeding that cluster with regulated 24VDC from a RSD150C-24.
On 9/9/2016 6:34 PM, George Skorup wrote:
Uh.. hmm. I have a 5.7 450 sector running at a tower without any
customers on it yet. It's powered and timed from a new GigE
PowerInjector+Sync. GigE-APC-HV at the bottom. No SS on top. ~225 feet
of Shireen 1042 cable.
I just logged into it and set it to Auto 1000F/100F/etc. and rebooted.
Does the same shit.
18:14:07 interface,info ether6 link down
18:14:20 interface,info ether6 link up (speed 1G, full duplex)
18:14:21 interface,info ether6 link down
18:14:26 interface,info ether6 link up (speed 1G, full duplex)
18:14:27 interface,info ether6 link down
18:14:30 interface,info ether6 link up (speed 1G, full duplex)
18:14:31 interface,info ether6 link down
18:14:40 interface,info ether6 link up (speed 100M, full duplex)
I also just set it back to Auto 100F (disabling gigabit negotiation)
and it does this...
18:21:34 interface,info ether6 link down
18:21:47 interface,info ether6 link up (speed 1G, full duplex)
18:21:48 interface,info ether6 link down
18:21:52 interface,info ether6 link up (speed 100M, full duplex)
So, looks like the boot loader brings it up at 1Gbps, then the config
makes it fall back to 100Mbps.
This is also the first time that I tried messing with GigE on the 450
since updating from 13.2.1 to 14.1.2.
This is a regular old RB1100. I have an Exalt ExtendAir G2-11 and an
AF24 each running on a GigE-POE-APC and gigabit works fine. Chuck
would have to say for sure, but I don't think there's much electrical
difference between the GigE-APC-HV and the GigE-POE-APC. Besides maybe
the gas-tube backup suppression and GigE transformer.
Me thinks this has more to do with Cambium.
On 9/9/2016 6:10 PM, George Skorup wrote:
I upgraded two CRS125-24G-1S-RM's to 6.36.3 (current branch). Both
brand new out of the boxes. Upgraded boot firmware to 3.33 on both.
Reset both to defaults. Ether24 to ether24 linked up at 1Gbps FDX.
Ran MT bandwidth tests between them. No issues.
Then I put a GigE-APC-HV in between with a 50' patch cable on one
side and a 10' on the other side. Tried with and without the ground
attached. Ran more bandwidth tests. No link drops. No errors.
So... I have no idea why you're having problems. The ones I have are
definitely HV Rev A1's.
On 9/9/2016 2:24 PM, Matt wrote:
I have a couple CRS125's on my bench that I can mess with this afternoon if
I have time.
Do you have a GigEAPC-HV? My setup was CRS125 -<~50 foot
UTP>-<GigEAPC-HV>-<20 foot UTP>- CRS125
