Hi,
I get following oops while unloading snd-intel8x0 on a Dell Optiplex 260
Kernel is 2.4.20aa1 (happens again with plain 2.4.20)
Alsa is 0.9.0rc6 (and CVS 20021204)
Debian/woody.
Christian
Here's /proc/pci
PCI devices found:
Bus 0, device 0, function 0:
Host bridge: Intel Corp. 82845G/GL [Brookdale-G] Chipset Host Bridge (rev
1).
Prefetchable 32 bit memory at 0xf0000000 [0xf7ffffff].
Bus 0, device 2, function 0:
VGA compatible controller: Intel Corp. 82845G/GL [Brookdale-G] Chipset
Integrated Graphics Device (rev 1).
IRQ 16.
Prefetchable 32 bit memory at 0xe8000000 [0xefffffff].
Non-prefetchable 32 bit memory at 0xff680000 [0xff6fffff].
Bus 0, device 29, function 0:
USB Controller: Intel Corp. 82801DB USB (Hub #1) (rev 1).
IRQ 16.
I/O at 0xff80 [0xff9f].
Bus 0, device 29, function 1:
USB Controller: Intel Corp. 82801DB USB (Hub #2) (rev 1).
IRQ 19.
I/O at 0xff60 [0xff7f].
Bus 0, device 29, function 2:
USB Controller: Intel Corp. 82801DB USB (Hub #3) (rev 1).
IRQ 18.
I/O at 0xff40 [0xff5f].
Bus 0, device 29, function 7:
USB Controller: Intel Corp. 82801DB USB EHCI Controller (rev 1).
IRQ 23.
Non-prefetchable 32 bit memory at 0xffa00800 [0xffa00bff].
Bus 0, device 30, function 0:
PCI bridge: Intel Corp. 82801BA/CA/DB PCI Bridge (rev 129).
Master Capable. No bursts. Min Gnt=6.
Bus 0, device 31, function 0:
ISA bridge: Intel Corp. 82801DB ISA Bridge (LPC) (rev 1).
Bus 0, device 31, function 1:
IDE interface: Intel Corp. 82801DB ICH4 IDE (rev 1).
IRQ 18.
I/O at 0x0 [0x7].
I/O at 0x0 [0x3].
I/O at 0x0 [0x7].
I/O at 0x0 [0x3].
I/O at 0xffa0 [0xffaf].
Non-prefetchable 32 bit memory at 0x1f800000 [0x1f8003ff].
Bus 0, device 31, function 3:
SMBus: Intel Corp. 82801DB SMBus (rev 1).
IRQ 17.
I/O at 0xdc80 [0xdc9f].
Bus 0, device 31, function 5:
Multimedia audio controller: Intel Corp. 82801DB AC'97 Audio (rev 1).
IRQ 17.
I/O at 0xd800 [0xd8ff].
I/O at 0xdc40 [0xdc7f].
Non-prefetchable 32 bit memory at 0xffa00400 [0xffa005ff].
Non-prefetchable 32 bit memory at 0xffa00000 [0xffa000ff].
Bus 1, device 12, function 0:
Ethernet controller: Intel Corp. 82540EM Gigabit Ethernet Controller (rev
2).
IRQ 18.
Master Capable. Latency=64. Min Gnt=255.
Non-prefetchable 32 bit memory at 0xff8e0000 [0xff8fffff].
I/O at 0xecc0 [0xecff].
-----------------------------------------------------------------------------
ksymoops 2.4.5 on i686 2.4.20aa1. Options used
-V (default)
-k /proc/ksyms (default)
-l /proc/modules (default)
-o /lib/modules/2.4.20aa1/ (default)
-m /boot/System.map-2.4.20aa1 (default)
Warning: You did not tell me where to find symbol information. I will
assume that the log matches the kernel and modules that are running
right now and I'll use the default options above for symbol resolution.
If the current kernel and/or modules do not match the log, you can get
more accurate output by telling me the kernel version and where to find
map, modules, ksyms etc. ksymoops -h explains the options.
Warning (compare_ksyms_lsmod): module snd-intel8x0 is in lsmod but not in
ksyms, probably no symbols exported
Dec 4 15:23:46 pc51167 kernel: CPU 0 (0x0000) enabledProcessor #0 Pentium
4(tm) XEON(tm) APIC version 16
Dec 4 15:23:46 pc51167 kernel: CPU 1 (0x0100) disabled
Dec 4 15:23:46 pc51167 kernel: CPU 2 (0x0100) disabled
Dec 4 15:23:46 pc51167 kernel: CPU 3 (0x0300) disabled
Dec 4 15:23:46 pc51167 kernel: cpu: 0, clocks: 996318, slice: 498159
Dec 4 15:23:46 pc51167 kernel: SGI XFS CVS with ACLs, quota, no debug enabled
Dec 4 15:23:46 pc51167 kernel: e1000: eth0 NIC Link is Up 100 Mbps Full Duplex
Dec 4 15:23:48 pc51167 kernel: ds: no socket drivers loaded!
Dec 4 15:24:42 pc51167 kernel: c01cfe37
Dec 4 15:24:42 pc51167 kernel: Oops: 0002 2.4.20aa1 #1 SMP Wed Dec 4 12:12:13
CET 2002
Dec 4 15:24:42 pc51167 kernel: CPU: 0
Dec 4 15:24:42 pc51167 kernel: EIP: 0010:[pci_unregister_driver+11/84]
Not tainted
Dec 4 15:24:42 pc51167 kernel: EFLAGS: 00010246
Dec 4 15:24:42 pc51167 kernel: eax: 00000000 ebx: c2c40000 ecx: c2ab4000
edx: 00000000
Dec 4 15:24:42 pc51167 kernel: esi: c2c445a0 edi: c41b0000 ebp: c027a074
esp: c44a1f7c
Dec 4 15:24:42 pc51167 kernel: ds: 0018 es: 0018 ss: 0018
Dec 4 15:24:42 pc51167 kernel: Process modprobe (pid: 871, stackpage=c44a1000)
Dec 4 15:24:42 pc51167 kernel: Stack: c2c40000 c027a074 c2c43320 c2c445a0
c2c444a0 c011b029 c2c40000 fffffff0
Dec 4 15:24:42 pc51167 kernel: c41b0000 c027a074 c011a34f c2c40000
00000000 c44a0000 00000000 bffffe50
Dec 4 15:24:42 pc51167 kernel: bfffeafc c01070f3 bffffe50 bffffe50
00000000 00000000 bffffe50 bfffeafc
Dec 4 15:24:42 pc51167 kernel: Call Trace:
[ehci-hcd:__insmod_ehci-hcd_S.data_L96+2881984/57020256]
[ehci-hcd:__insmod_ehci-hcd_S.data_L96+2886720/57015520]
[ehci-hcd:__insmod_ehci-hcd_S.data_L96+2886464/57015776] [free_module+45/212]
[sys_delete_module+311/616]
Dec 4 15:24:42 pc51167 kernel: Code: 89 50 04 89 02 c7 06 00 00 00 00 c7 46 04
00 00 00 00 8b 1d
ebx; c2c40000 <[snd-pcm].data.end+fc75/1fc75>
ecx; c2ab4000 <[ehci-hcd].data.end+130641/29c641>
esi; c2c445a0 <[snd-pcm].data.end+14215/1fc75>
edi; c41b0000 <END_OF_CODE+bf218d/????>
ebp; c027a074 <module_mutex+0/14>
esp; c44a1f7c <END_OF_CODE+ee4109/????>
Code; 00000000 Before first symbol
00000000 <_EIP>:
Code; 00000000 Before first symbol
0: 89 50 04 mov %edx,0x4(%eax)
Code; 00000003 Before first symbol
3: 89 02 mov %eax,(%edx)
Code; 00000005 Before first symbol
5: c7 06 00 00 00 00 movl $0x0,(%esi)
Code; 0000000b Before first symbol
b: c7 46 04 00 00 00 00 movl $0x0,0x4(%esi)
Code; 00000012 Before first symbol
12: 8b 1d 00 00 00 00 mov 0x0,%ebx
---------------------------------------------------------------------------
Linux version 2.4.20aa1 (root@pc51167) (gcc version 2.95.4 20011002 (Debian
prerelease)) #1 SMP Wed Dec 4 12:12:13 CET 2002
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001f771000 (usable)
BIOS-e820: 000000001f771000 - 000000001f773000 (ACPI NVS)
BIOS-e820: 000000001f773000 - 000000001f794000 (ACPI data)
BIOS-e820: 000000001f794000 - 000000001f800000 (reserved)
BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee10000 (reserved)
BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
503MB LOWMEM available.
found SMP MP-table at 000fe710
hm, page 000fe000 reserved twice.
hm, page 000ff000 reserved twice.
hm, page 000f0000 reserved twice.
On node 0 totalpages: 128881
zone(0): 4096 pages.
zone(1): 124785 pages.
zone(2): 0 pages.
ACPI: Searched entire block, no RSDP was found.
ACPI: RSDP located at physical address c00feba0
RSD PTR v0 [DELL ]
__va_range(0xfd501, 0x68): idx=8 mapped at ffff6000
ACPI table found: RSDT v1 [DELL GX260 0.6]
__va_range(0xfd539, 0x24): idx=8 mapped at ffff6000
__va_range(0xfd539, 0x74): idx=8 mapped at ffff6000
ACPI table found: FACP v1 [DELL GX260 0.6]
__va_range(0xfffd82e7, 0x24): idx=8 mapped at ffff6000
__va_range(0xfffd82e7, 0xa7): idx=8 mapped at ffff6000
ACPI table found: SSDT v1 [DELL st_ex 0.4096]
__va_range(0xfd5ad, 0x24): idx=8 mapped at ffff6000
__va_range(0xfd5ad, 0x6c): idx=8 mapped at ffff6000
ACPI table found: APIC v1 [DELL GX260 0.6]
__va_range(0xfd5ad, 0x6c): idx=8 mapped at ffff6000
LAPIC (acpi_id[0x0001] id[0x0] enabled[1])
CPU 0 (0x0000) enabledProcessor #0 Pentium 4(tm) XEON(tm) APIC version 16
LAPIC (acpi_id[0x0002] id[0x1] enabled[0])
CPU 1 (0x0100) disabled
LAPIC (acpi_id[0x0003] id[0x1] enabled[0])
CPU 2 (0x0100) disabled
LAPIC (acpi_id[0x0004] id[0x3] enabled[0])
CPU 3 (0x0300) disabled
IOAPIC (id[0x1] address[0xfec00000] global_irq_base[0x0])
INT_SRC_OVR (bus[0] irq[0x0] global_irq[0x2] polarity[0x0] trigger[0x0])
INT_SRC_OVR (bus[0] irq[0x9] global_irq[0x9] polarity[0x1] trigger[0x3])
4 CPUs total
Local APIC address fee00000
__va_range(0xfd619, 0x24): idx=8 mapped at ffff6000
__va_range(0xfd619, 0x28): idx=8 mapped at ffff6000
ACPI table found: BOOT v1 [DELL GX260 0.6]
__va_range(0xfd641, 0x24): idx=8 mapped at ffff6000
__va_range(0xfd641, 0x67): idx=8 mapped at ffff6000
ACPI table found: ASF! v16 [DELL GX260 0.6]
ACPI: Unsupported table ASF!
Enabling the CPU's according to the ACPI table
Intel MultiProcessor Specification v1.4
Virtual Wire compatibility mode.
OEM ID: DELL Product ID: Opti GX260 APIC at: 0xFEE00000
I/O APIC #1 Version 32 at 0xFEC00000.
Processors: 1
Building zonelist for node : 0
Kernel command line: BOOT_IMAGE=Linux ro root=301
Initializing CPU#0
Detected 1992.652 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 3971.48 BogoMIPS
Memory: 506528k/515524k available (1205k kernel code, 8612k reserved, 548k
data, 100k init, 0k highmem)
Dentry cache hash table entries: 65536 (order: 7, 524288 bytes)
Inode cache hash table entries: 32768 (order: 6, 262144 bytes)
Mount-cache hash table entries: 8192 (order: 4, 65536 bytes)
Buffer-cache hash table entries: 32768 (order: 5, 131072 bytes)
Page-cache hash table entries: 131072 (order: 7, 524288 bytes)
CPU: L1 I cache: 0K, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Hyper-Threading is disabled
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: 3febfbff 00000000 00000000 00000000
CPU: Common caps: 3febfbff 00000000 00000000 00000000
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch ([EMAIL PROTECTED])
mtrr: detected mtrr type: Intel
CPU: L1 I cache: 0K, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Hyper-Threading is disabled
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: 3febfbff 00000000 00000000 00000000
CPU: Common caps: 3febfbff 00000000 00000000 00000000
CPU0: Intel(R) Pentium(R) 4 CPU 2.00GHz stepping 04
per-CPU timeslice cutoff: 1462.62 usecs.
task migration cache decay timeout: 10 msecs.
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Error: only one processor found.
ENABLING IO-APIC IRQs
Setting 1 in the phys_id_present_map
...changing IO-APIC physical APIC ID to 1 ... ok.
init IO_APIC IRQs
IO-APIC (apicid-pin) 1-0, 1-13, 1-20, 1-21, 1-22 not connected.
..TIMER: vector=0x31 pin1=2 pin2=0
number of MP IRQ sources: 41.
number of IO-APIC #1 registers: 24.
testing the IO APIC.......................
IO APIC #1......
.... register #00: 01000000
....... : physical APIC id: 01
.... register #01: 00178020
....... : max redirection entries: 0017
....... : PRQ implemented: 1
....... : IO APIC version: 0020
.... register #02: 00000000
....... : arbitration: 00
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 000 00 1 0 0 0 0 0 0 00
01 001 01 0 0 0 0 0 1 1 39
02 001 01 0 0 0 0 0 1 1 31
03 001 01 0 0 0 0 0 1 1 41
04 001 01 0 0 0 0 0 1 1 49
05 001 01 0 0 0 0 0 1 1 51
06 001 01 0 0 0 0 0 1 1 59
07 001 01 0 0 0 0 0 1 1 61
08 001 01 0 0 0 0 0 1 1 69
09 001 01 0 0 0 0 0 1 1 71
0a 001 01 0 0 0 0 0 1 1 79
0b 001 01 0 0 0 0 0 1 1 81
0c 001 01 0 0 0 0 0 1 1 89
0d 000 00 1 0 0 0 0 0 0 00
0e 001 01 0 0 0 0 0 1 1 91
0f 001 01 0 0 0 0 0 1 1 99
10 001 01 1 1 0 1 0 1 1 A1
11 001 01 1 1 0 1 0 1 1 A9
12 001 01 1 1 0 1 0 1 1 B1
13 001 01 1 1 0 1 0 1 1 B9
14 000 00 1 0 0 0 0 0 0 00
15 000 00 1 0 0 0 0 0 0 00
16 000 00 1 0 0 0 0 0 0 00
17 001 01 1 1 0 1 0 1 1 C1
IRQ to pin mappings:
IRQ0 -> 0:2
IRQ1 -> 0:1
IRQ3 -> 0:3
IRQ4 -> 0:4
IRQ5 -> 0:5
IRQ6 -> 0:6
IRQ7 -> 0:7
IRQ8 -> 0:8
IRQ9 -> 0:9
IRQ10 -> 0:10
IRQ11 -> 0:11
IRQ12 -> 0:12
IRQ14 -> 0:14
IRQ15 -> 0:15
IRQ16 -> 0:16
IRQ17 -> 0:17
IRQ18 -> 0:18
IRQ19 -> 0:19
IRQ23 -> 0:23
.................................... done.
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 1992.6392 MHz.
..... host bus clock speed is 99.6318 MHz.
cpu: 0, clocks: 996318, slice: 498159
CPU0<T0:996304,T1:498144,D:1,S:498159,C:996318>
migration_task 0 on cpu=0
PCI: PCI BIOS revision 2.10 entry at 0xfbdf8, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
Transparent bridge - Intel Corp. 82801BA/CA/DB PCI Bridge
PCI: Using IRQ router PIIX [8086/24c0] at 00:1f.0
PCI->APIC IRQ transform: (B0,I2,P0) -> 16
PCI->APIC IRQ transform: (B0,I29,P0) -> 16
PCI->APIC IRQ transform: (B0,I29,P1) -> 19
PCI->APIC IRQ transform: (B0,I29,P2) -> 18
PCI->APIC IRQ transform: (B0,I29,P3) -> 23
PCI->APIC IRQ transform: (B0,I31,P0) -> 18
PCI->APIC IRQ transform: (B0,I31,P1) -> 17
PCI->APIC IRQ transform: (B0,I31,P1) -> 17
PCI->APIC IRQ transform: (B1,I12,P0) -> 18
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
bigpage subsystem: allocated 0 bigpages (=0MB).
VFS: Disk quotas vdquot_6.5.1
aio_setup: num_physpages = 32220
aio_setup: sizeof(struct page) = 48
devfs: v1.12c (20020818) Richard Gooch ([EMAIL PROTECTED])
devfs: boot_options: 0x1
Installing knfsd (copyright (C) 1996 [EMAIL PROTECTED]).
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI
enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH4: IDE controller on PCI bus 00 dev f9
PCI: Device 00:1f.1 not available because of resource collisions
ICH4: BIOS setup was incomplete.
ICH4: chipset revision 1
ICH4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:DMA, hdd:pio
hda: ST340016A, ATA DISK drive
hdc: HL-DT-ST GCE-8400B, ATAPI CD/DVD-ROM drive
hdd: SAMSUNG DVD-ROM SD-616, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
blk: queue c03539a4, I/O limit 4095Mb (mask 0xffffffff)
hda: 78165360 sectors (40021 MB) w/2048KiB Cache, CHS=4865/255/63, UDMA(100)
Partition check:
/dev/ide/host0/bus0/target0/lun0: p1 p2 p3 p4 < p5 >
md: raid5 personality registered as nr 4
raid5: measuring checksumming speed
8regs : 2299.600 MB/sec
32regs : 1745.600 MB/sec
pIII_sse : 2596.800 MB/sec
pII_mmx : 2285.200 MB/sec
p5_mmx : 2306.800 MB/sec
raid5: using function: pIII_sse (2596.800 MB/sec)
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 32768)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (ext2 filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 100k freed
Adding Swap: 995988k swap-space (priority -1)
Real Time Clock Driver v1.10e
Intel(R) PRO/1000 Network Driver - version 4.4.12-k1
Copyright (c) 1999-2002 Intel Corporation.
eth0: Intel(R) PRO/1000 Network Connection
SGI XFS CVS with ACLs, quota, no debug enabled
XFS mounting filesystem ide0(3,2)
XFS mounting filesystem ide0(3,3)
e1000: eth0 NIC Link is Up 100 Mbps Full Duplex
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
PCI: Setting latency timer of device 00:1d.7 to 64
hcd.c: ehci-hcd @ 00:1d.7, Intel Corp. 82801DB USB EHCI Controller
hcd.c: irq 23, pci mem e009e800
usb.c: new USB bus registered, assigned bus number 1
ehci-hcd.c: restricting 64bit DMA mappings to segment 0 ...
ehci-hcd.c: USB 2.0 support enabled, EHCI rev 1. 0
hub.c: USB hub found
hub.c: 6 ports detected
usb-uhci.c: $Revision: 1.275 $ time 12:17:56 Dec 4 2002
usb-uhci.c: High bandwidth mode enabled
PCI: Setting latency timer of device 00:1d.0 to 64
usb-uhci.c: USB UHCI at I/O 0xff80, IRQ 16
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Setting latency timer of device 00:1d.1 to 64
usb-uhci.c: USB UHCI at I/O 0xff60, IRQ 19
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 3
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Setting latency timer of device 00:1d.2 to 64
usb-uhci.c: USB UHCI at I/O 0xff40, IRQ 18
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 4
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
PCI: Setting latency timer of device 00:1f.5 to 64
Linux Kernel Card Services 3.1.22
options: [pci] [cardbus]
ds: no socket drivers loaded!
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE]
parport0: irq 7 detected
lp0: using parport0 (polling).
Unable to handle kernel NULL pointer dereference at virtual address 00000004
printing eip:
c01cfe37
*pde = 00000000
Oops: 0002 2.4.20aa1 #1 SMP Wed Dec 4 12:12:13 CET 2002
CPU: 0
EIP: 0010:[<c01cfe37>] Not tainted
EFLAGS: 00010246
eax: 00000000 ebx: c2c40000 ecx: c2ab4000 edx: 00000000
esi: c2c445a0 edi: c41b0000 ebp: c027a074 esp: c44a1f7c
ds: 0018 es: 0018 ss: 0018
Process modprobe (pid: 871, stackpage=c44a1000)
Stack: c2c40000 c027a074 c2c43320 c2c445a0 c2c444a0 c011b029 c2c40000 fffffff0
c41b0000 c027a074 c011a34f c2c40000 00000000 c44a0000 00000000 bffffe50
bfffeafc c01070f3 bffffe50 bffffe50 00000000 00000000 bffffe50 bfffeafc
Call Trace: [<c2c43320>] [<c2c445a0>] [<c2c444a0>] [<c011b029>] [<c011a34f>]
[<c01070f3>]
Modules: [(snd-intel8x0:<c2c40060>:<c2c44620>)]
Code: 89 50 04 89 02 c7 06 00 00 00 00 c7 46 04 00 00 00 00 8b 1d
-------------------------------------------------------
This sf.net email is sponsored by:ThinkGeek
Welcome to geek heaven.
http://thinkgeek.com/sf
_______________________________________________
Alsa-user mailing list
[EMAIL PROTECTED]
https://lists.sourceforge.net/lists/listinfo/alsa-user
-------------------------------------------------------
This sf.net email is sponsored by:ThinkGeek
Welcome to geek heaven.
http://thinkgeek.com/sf
_______________________________________________
Alsa-devel mailing list
[EMAIL PROTECTED]
https://lists.sourceforge.net/lists/listinfo/alsa-devel
