Hi,
right now I'm trying to change the slot mapping register 0x5e, clear AMAP bit set new
slot but nothing 0x5e is still 0x0000 ?
CU
Bernd Zierath
-----Original Message-----
From: Zierath Bernd
Sent: Fri 2/28/2003 11:31 AM
To: [EMAIL PROTECTED]
Cc:
Subject: RE: [Alsa-devel] AC3 passthru intel8x0 + cs4299
Hi,
here are my current config
lspci -v
00:1f.5 Multimedia audio controller: Intel Corp. 82801AA AC'97 Audio (rev 02)
Subsystem: Siemens Nixdorf AG: Unknown device 0051
Flags: bus master, medium devsel, latency 0, IRQ 5
I/O ports at 2000 [size=256]
I/O ports at 1800 [size=64]
-------------
0-0/0: Cirrus Logic CS4299 rev 4
Capabilities : -headphone out-
DAC resolution : 20-bit
ADC resolution : 18-bit
3D enhancement : Crystal Semi 3D Stereo Enhancement
Current setup
Mic gain : +20dB [+20dB]
POP path : pre 3D
Sim. stereo : off
3D enhancement : on
Loudness : off
Mono output : MIX
Mic select : Mic1
ADC/DAC loopback : off
Extended ID : codec=0 rev=0 AMAP DSA=0 VRA
Extended status : VRA
PCM front DAC : 48000Hz
PCM ADC : 48000Hz
SPDIF Control : Consumer PCM Copyright Category=0x2 Generation=1 Rate=48kHz
E
nabled
-------------
0:00 = 1990
0:02 = 1313
0:04 = 1f1f
0:06 = 001f
0:08 = 0000
0:0a = 001e
0:0c = 001f
0:0e = 005f
0:10 = 1f1f
0:12 = 1f1f
0:14 = 1f1f
0:16 = 1f1f
0:18 = 1f1f
0:1a = 0000
0:1c = 0000
0:1e = 0000
0:20 = 2000
0:22 = 0000
0:24 = 0000
0:26 = 000f
0:28 = 0201
0:2a = 0001
0:2c = bb80
0:2e = 0000
0:30 = 0000
0:32 = bb80
0:34 = 0000
0:36 = 0000
0:38 = 0000
0:3a = 0000
0:3c = 0000
0:3e = 0000
0:40 = 0000
0:42 = 0000
0:44 = 0000
0:46 = 0000
0:48 = 0000
0:4a = 0000
0:4c = 0000
0:4e = 0000
0:50 = 0000
0:52 = 0000
0:54 = 0000
0:56 = ffff
0:58 = 0000
0:5a = 0404
0:5c = 0000
0:5e = 0080
0:60 = 0022
0:62 = 0000
0:64 = 0000
0:66 = 0000
0:68 = 8824
0:6a = 0000
0:6c = 0000
0:6e = 0000
0:70 = 0000
0:72 = 0000
0:74 = 0000
0:76 = 0000
0:78 = 007e
0:7a = 0000
0:7c = 4352
0:7e = 5934
-------------
Intel8x0
Global control : 0x00000002
Global status : 0x00000100
AC'97 codecs ready : primary
-------------
0 [82801AAICH ]: ICH - Intel 82801AA-ICH
Intel 82801AA-ICH at 0x2000, irq 5
--------------
0: [0- 0]: ctl
16: [0- 0]: digital audio playback
24: [0- 0]: digital audio capture
33: : timer
---------------
pcm
00-00: Intel ICH : Intel 82801AA-ICH : playback 1 : capture 1
---------------
what I'm trying , change no audio bit to 1 reg 0x68 in ac97_codec.c
snd_ac97_spdif_default_put().
but I get errors in
intel8x0: clocking to 48000
ALSA ../alsa-kernel/pci/intel8x0.c:521: codec_semaphore: semaphore is not
ready[0x1][0x100]
ALSA ../alsa-kernel/pci/intel8x0.c:553: codec_read 0: semaphore is not ready
for register 0x56
I try activate the SPSA control in snd_ac97_mixer_build() like cs4205.
I also have no clue right now about the registers 0x30 and 0x34.
0x34 is maybe Codec Write Semaphore Register
CU
Bernd Zierath
-------------------------------------------------------
This sf.net email is sponsored by:ThinkGeek
Welcome to geek heaven.
http://thinkgeek.com/sf
_______________________________________________
Alsa-devel mailing list
[EMAIL PROTECTED]
https://lists.sourceforge.net/lists/listinfo/alsa-devel
N�HY隊X���'���u���{��� �� N�Z�X��8^u���~�ܢje{(u��n� �x�/��� ���q��y��ʋ�y�b�
h�֧uج����םN�Z�X��Ƨ��iʋ��wr���k /j)ZnW��f���
!v�t���ej��k�(�~��� [EMAIL PROTECTED],���y�+���b��?�+-�w���liׯz
