----- Original Message ----- From: "DJ A. J. Slye" <[EMAIL PROTECTED]> To: "Clemens Ladisch" <[EMAIL PROTECTED]> Sent: Friday, September 07, 2007 9:15 AM Subject: Re: [Alsa-user] BCD2000
>I wasn't sure about which parts we're for the BCD2000 only so here is the > whole output: > > [EMAIL PROTECTED]:~# lsusb -v > > Bus 003 Device 002: ID 1397:00bd > Device Descriptor: > bLength 18 > bDescriptorType 1 > bcdUSB 1.00 > bDeviceClass 0 (Defined at Interface level) > bDeviceSubClass 0 > bDeviceProtocol 0 > bMaxPacketSize0 8 > idVendor 0x1397 > idProduct 0x00bd > bcdDevice 0.00 > iManufacturer 1 Behringer > iProduct 2 BCD2000 > iSerial 0 > bNumConfigurations 1 > Configuration Descriptor: > bLength 9 > bDescriptorType 2 > wTotalLength 46 > bNumInterfaces 1 > bConfigurationValue 1 > iConfiguration 0 > bmAttributes 0x80 > (Bus Powered) > MaxPower 100mA > Interface Descriptor: > bLength 9 > bDescriptorType 4 > bInterfaceNumber 0 > bAlternateSetting 0 > bNumEndpoints 4 > bInterfaceClass 255 Vendor Specific Class > bInterfaceSubClass 0 > bInterfaceProtocol 0 > iInterface 0 > Endpoint Descriptor: > bLength 7 > bDescriptorType 5 > bEndpointAddress 0x01 EP 1 OUT > bmAttributes 3 > Transfer Type Interrupt > Synch Type None > Usage Type Data > wMaxPacketSize 0x0040 1x 64 bytes > bInterval 1 > Endpoint Descriptor: > bLength 7 > bDescriptorType 5 > bEndpointAddress 0x81 EP 1 IN > bmAttributes 3 > Transfer Type Interrupt > Synch Type None > Usage Type Data > wMaxPacketSize 0x0040 1x 64 bytes > bInterval 1 > Endpoint Descriptor: > bLength 7 > bDescriptorType 5 > bEndpointAddress 0x02 EP 2 OUT > bmAttributes 1 > Transfer Type Isochronous > Synch Type None > Usage Type Data > wMaxPacketSize 0x0180 1x 384 bytes > bInterval 1 > Endpoint Descriptor: > bLength 7 > bDescriptorType 5 > bEndpointAddress 0x83 EP 3 IN > bmAttributes 1 > Transfer Type Isochronous > Synch Type None > Usage Type Data > wMaxPacketSize 0x0180 1x 384 bytes > bInterval 1 > Device Status: 0x0001 > Self Powered > > Bus 003 Device 001: ID 0000:0000 > Device Descriptor: > bLength 18 > bDescriptorType 1 > bcdUSB 1.10 > bDeviceClass 9 Hub > bDeviceSubClass 0 Unused > bDeviceProtocol 0 Full speed hub > bMaxPacketSize0 64 > idVendor 0x0000 > idProduct 0x0000 > bcdDevice 2.06 > iManufacturer 3 Linux 2.6.20-16-lowlatency ohci_hcd > iProduct 2 OHCI Host Controller > iSerial 1 0000:00:02.1 > bNumConfigurations 1 > Configuration Descriptor: > bLength 9 > bDescriptorType 2 > wTotalLength 25 > bNumInterfaces 1 > bConfigurationValue 1 > iConfiguration 0 > bmAttributes 0xe0 > Self Powered > Remote Wakeup > MaxPower 0mA > Interface Descriptor: > bLength 9 > bDescriptorType 4 > bInterfaceNumber 0 > bAlternateSetting 0 > bNumEndpoints 1 > bInterfaceClass 9 Hub > bInterfaceSubClass 0 Unused > bInterfaceProtocol 0 Full speed hub > iInterface 0 > Endpoint Descriptor: > bLength 7 > bDescriptorType 5 > bEndpointAddress 0x81 EP 1 IN > bmAttributes 3 > Transfer Type Interrupt > Synch Type None > Usage Type Data > wMaxPacketSize 0x0002 1x 2 bytes > bInterval 255 > Hub Descriptor: > bLength 9 > bDescriptorType 41 > nNbrPorts 3 > wHubCharacteristic 0x0002 > No power switching (usb 1.0) > Ganged overcurrent protection > bPwrOn2PwrGood 1 * 2 milli seconds > bHubContrCurrent 0 milli Ampere > DeviceRemovable 0x00 > PortPwrCtrlMask 0xff > Hub Port Status: > Port 1: 0000.0103 power enable connect > Port 2: 0000.0100 power > Port 3: 0000.0100 power > Device Status: 0x0003 > Self Powered > Remote Wakeup Enabled > > Bus 001 Device 001: ID 0000:0000 > Device Descriptor: > bLength 18 > bDescriptorType 1 > bcdUSB 1.10 > bDeviceClass 9 Hub > bDeviceSubClass 0 Unused > bDeviceProtocol 0 Full speed hub > bMaxPacketSize0 64 > idVendor 0x0000 > idProduct 0x0000 > bcdDevice 2.06 > iManufacturer 3 Linux 2.6.20-16-lowlatency ohci_hcd > iProduct 2 OHCI Host Controller > iSerial 1 0000:00:02.0 > bNumConfigurations 1 > Configuration Descriptor: > bLength 9 > bDescriptorType 2 > wTotalLength 25 > bNumInterfaces 1 > bConfigurationValue 1 > iConfiguration 0 > bmAttributes 0xe0 > Self Powered > Remote Wakeup > MaxPower 0mA > Interface Descriptor: > bLength 9 > bDescriptorType 4 > bInterfaceNumber 0 > bAlternateSetting 0 > bNumEndpoints 1 > bInterfaceClass 9 Hub > bInterfaceSubClass 0 Unused > bInterfaceProtocol 0 Full speed hub > iInterface 0 > Endpoint Descriptor: > bLength 7 > bDescriptorType 5 > bEndpointAddress 0x81 EP 1 IN > bmAttributes 3 > Transfer Type Interrupt > Synch Type None > Usage Type Data > wMaxPacketSize 0x0002 1x 2 bytes > bInterval 255 > Hub Descriptor: > bLength 9 > bDescriptorType 41 > nNbrPorts 3 > wHubCharacteristic 0x0002 > No power switching (usb 1.0) > Ganged overcurrent protection > bPwrOn2PwrGood 1 * 2 milli seconds > bHubContrCurrent 0 milli Ampere > DeviceRemovable 0x00 > PortPwrCtrlMask 0xff > Hub Port Status: > Port 1: 0000.0100 power > Port 2: 0000.0100 power > Port 3: 0000.0100 power > Device Status: 0x0003 > Self Powered > Remote Wakeup Enabled > > Bus 002 Device 001: ID 0000:0000 > Device Descriptor: > bLength 18 > bDescriptorType 1 > bcdUSB 2.00 > bDeviceClass 9 Hub > bDeviceSubClass 0 Unused > bDeviceProtocol 1 Single TT > bMaxPacketSize0 64 > idVendor 0x0000 > idProduct 0x0000 > bcdDevice 2.06 > iManufacturer 3 Linux 2.6.20-16-lowlatency ehci_hcd > iProduct 2 EHCI Host Controller > iSerial 1 0000:00:02.2 > bNumConfigurations 1 > Configuration Descriptor: > bLength 9 > bDescriptorType 2 > wTotalLength 25 > bNumInterfaces 1 > bConfigurationValue 1 > iConfiguration 0 > bmAttributes 0xe0 > Self Powered > Remote Wakeup > MaxPower 0mA > Interface Descriptor: > bLength 9 > bDescriptorType 4 > bInterfaceNumber 0 > bAlternateSetting 0 > bNumEndpoints 1 > bInterfaceClass 9 Hub > bInterfaceSubClass 0 Unused > bInterfaceProtocol 0 Full speed hub > iInterface 0 > Endpoint Descriptor: > bLength 7 > bDescriptorType 5 > bEndpointAddress 0x81 EP 1 IN > bmAttributes 3 > Transfer Type Interrupt > Synch Type None > Usage Type Data > wMaxPacketSize 0x0004 1x 4 bytes > bInterval 12 > Hub Descriptor: > bLength 9 > bDescriptorType 41 > nNbrPorts 6 > wHubCharacteristic 0x000a > No power switching (usb 1.0) > Per-port overcurrent protection > TT think time 8 FS bits > bPwrOn2PwrGood 10 * 2 milli seconds > bHubContrCurrent 0 milli Ampere > DeviceRemovable 0x00 > PortPwrCtrlMask 0xff > Hub Port Status: > Port 1: 0000.0100 power > Port 2: 0000.0100 power > Port 3: 0000.0000 > Port 4: 0000.0100 power > Port 5: 0000.0100 power > Port 6: 0000.0100 power > Device Status: 0x0003 > Self Powered > Remote Wakeup Enabled > > > ----- Original Message ----- > From: "Clemens Ladisch" <[EMAIL PROTECTED]> > To: "DJ A. J. Slye" <[EMAIL PROTECTED]> > Cc: <alsa-user@lists.sourceforge.net> > Sent: Tuesday, September 04, 2007 2:38 AM > Subject: Re: [Alsa-user] BCD2000 > > >> DJ A. J. Slye wrote: >>> Can someone please write a driver for the BCD2000 and BCD3000 please.. >> >> The BCD3000 manual says that it works in OS X without a separate driver. >> This means that it's class compliant and should work in Linux, too. >> >> I don't know anything about the BCD2000. If you have the device, please >> show the output of "lsusb -v" for this device. >> >> >> Regards, >> Clemens > ------------------------------------------------------------------------- This SF.net email is sponsored by: Microsoft Defy all challenges. Microsoft(R) Visual Studio 2005. http://clk.atdmt.com/MRT/go/vse0120000070mrt/direct/01/ _______________________________________________ Alsa-user mailing list Alsa-user@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/alsa-user
