Hi Mark,

I did not have any problems with bleeding because I am not writing anything 
back to AB, I just crank up the seperate opts and then save the results to 
spreadsheets when they are finished. FWIW, I was careful to close them in the 
reverse order that I opened them...I have not tried it with IO yet, and it may 
be a little while as I generally like to see results for all combinations of 
param values in order to look for possible relationships and the like...

Yes AFAIK they work independently. I think the best way to look at it is that I 
am basically taking advantage of the quad-core's enhanced multi-tasking 
abilities to use all available CPU power...

Steve
  ----- Original Message ----- 
  From: MarkK 
  To: [email protected] 
  Sent: Thursday, May 22, 2008 11:20 PM
  Subject: RE: [amibroker] Quad-core test results


  Steve,

   

  I am under the impression that each instance of AB runs from the same 
register key 

  When you have multiple instances open and run each AB separately is there any 
"bleeding" of information from one to the other?

  What about running Fred's IO program?

   

  Will all work independently with different instances open at the same time?

  Thank you for your feedback

   

   

   

   

  MarkK



  From: [email protected] [mailto:[EMAIL PROTECTED] On Behalf Of Steve 
Dugas
  Sent: Thursday, May 22, 2008 8:50 PM
  To: Yahoo - AmiBroker
  Subject: [amibroker] Quad-core test results

   

  Hi All,

   

  I finished setting up the new quad-core machine and ran my first tests today, 
so am posting the promised test results. All I can say is Wow!  Really nice 
improvements, even better than I expected to see in my highest hopes. I am 
happy as a pig in sh*t !!     8 - )

   

  For background, the test was an optimization run on a single ticker, which is 
how I will be running all my other tests ( ticker was QID, 468 EOD data bars ). 
All tests used the same code with different param settings, all tests had about 
46,000 opt steps.

   

  To put things in perspective and show why I am so happy, the original code 
was about 2,400 lines. The first time I ran it, on my old backup computer which 
I was using as a dedicated optimization machine, it took 7 1/2 hours to run. So 
then I copied the code and created a shorter version, removing everything which 
wasn't absolutley necessary for the optimizer, and that reduced the run time to 
2 1/2 hours. Then I ran this short version on my faster primary machine and 
that took 1 1/4 hours, which is about what I was expecting to see on the new 
machine.

   

  So today I started by running just ran one instance on the quad-core - that 
took only 30 mins and Task Manager showed it was using just 25% of the total 
processing power!  Well to make a long story short, I kept adding one instance 
at a time, all instances ran in 30 mins and each used up an additional 25% of 
the CPU power. In the end, I was easily running 4 simultaneous instances. This 
pretty much kept the CPU tached at 100% but all instances ran fine, all 
finished in 30 mins and I didn't experience any problems at all. I was even 
saving the first ones to spreadsheets while the final ones were still 
finishing, wow everything just worked flawlessly!  So, the quad-core can run 4 
seperate opts simultaneously in 30 mins, which averages out to 7 1/2 minutes 
per opt, which = 

   

  10X improvement over running the short code on the fast machine...

  20X improvement over running the short code on the old dedicated optimization 
machine...

  60X improvement over running the original code on the old optimization 
machine...  Awesome !!!

   

  To those who were wondering what is the best machine to get for running AB, 
it looks to me like quad is the way to go.  ( My machine has an Intel 
processor, which TJ mentioned should probably work better than AMD for this 
stuff )....

   

  Steve


  No virus found in this incoming message.
  Checked by AVG.
  Version: 8.0.100 / Virus Database: 269.24.0/1461 - Release Date: 5/22/2008 
4:44 PM

   

Reply via email to