I try to run Android on my PXA270 board... Kernel version is 2.6.19. After hard fight I succesfully applied patch. I have new shiny kernel. My board starts from SD card. Bootloader (u-boot) starts from flash and it searches for kernel on SD card. First partition of SD card contains kernel (FAT16): linux.igz Second partition of SD card contains filesystem (ext3)... /cache /data /dev /etc /proc /sbin (contains init) /sys /system /tmp /var
It starts...boot kernel, but there is problem with init process... Take a look : U-Boot 1.1.6 (Apr 2 2008 - 14:35:33) DRAM: 64 MB Flash: 2 MB NAND: 64 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Hit any key to stop autoboot: 0 Detected: 2027008 blocks of 512 bytes (989MB) SD card. Vendor: Man 11 OEM JC "064MB" Date 11/2003 Product: 320 Revision: 0.10 reading linux.igz 1169832 bytes read ## Booting image at a1000000 ... Image Name: Linux Kernel Image Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 1169768 Bytes = 1.1 MB Load Address: a0800000 Entry Point: a0800000 Verifying Checksum ... OK OK Starting kernel ... Uncompressing Linux................................................................................ done, booting the kern. Linux version 2.6.19_RC15 ([EMAIL PROTECTED]) (gcc version 4.2.1 (CodeSourcery Sourcery G++ Lite 2007q3-53)) #210 Thu Apr 10 09:8 CPU: XScale-PXA270 [69054117] revision 7 (ARMv5TE), cr=0000397f Machine: HITEC Memory policy: ECC disabled, Data cache writeback Run Mode clock: 208.00MHz (*16) Turbo Mode clock: 416.00MHz (*2.0, active) Memory clock: 104.00MHz (/2) System bus clock: 208.00MHz Standard (MSC0= 0x13387aa8) NAND mode The additional board GPIO's are configured CPU0: D VIVT undefined 5 cache CPU0: I cache: 32768 bytes, associativity 32, 32 byte lines, 32 sets CPU0: D cache: 32768 bytes, associativity 32, 32 byte lines, 32 sets Built 1 zonelists. Total pages: 16256 Kernel command line: console=ttyS0,115200 root=/dev/mmcblk0p2 ro PID hash table entries: 256 (order: 8, 1024 bytes) start_kernel(): bug: interrupts were enabled early Console: colour dummy device 80x30 Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) Memory: 64MB = 64MB total Memory: 62336KB available (2124K code, 242K data, 204K init) Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok NET: Registered protocol family 16 NET: Registered protocol family 2 IP route cache hash table entries: 512 (order: -1, 2048 bytes) TCP established hash table entries: 2048 (order: 1, 8192 bytes) TCP bind hash table entries: 1024 (order: 0, 4096 bytes) TCP: Hash tables configured (established 2048 bind 1024) TCP reno registered squashfs: version 3.2-r2 (2007/01/15) Phillip Lougher squashfs: LZMA suppport for slax.org by jro JFFS2 version 2.2. (NAND) (C) 2001-2006 Red Hat, Inc. yaffs Apr 10 2008 09:36:39 Installing. io scheduler noop registered io scheduler anticipatory registered (default) Hitec Backlight Driver Initialized. External logo in flash not found @ 0x1c0000 pxa2xx-uart.0: ttyS0 at MMIO 0x40100000 (irq = 22) is a FFUART pxa2xx-uart.1: ttyS1 at MMIO 0x40200000 (irq = 21) is a BTUART pxa2xx-uart.2: ttyS2 at MMIO 0x40700000 (irq = 20) is a STUART PPP generic driver version 2.4.2 PPP Deflate Compression module registered PPP BSD Compression module registered PPP MPPE Compression module registered Found: AMD AM29LV160DB THB PXA module: Found 1 x16 devices at 0x0 in 16-bit bank number of JEDEC chips: 1 cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness. Using static partition definition Creating 2 MTD partitions on "THB PXA module": 0x00000000-0x00040000 : "boot" 0x00040000-0x001f0000 : "kernel" NAND device: Manufacturer ID: 0xec, Chip ID: 0x76 (Samsung NAND 64MiB 3,3V 8-bit) Using static partition definition Creating 4 MTD partitions on "NAND 64MiB 3,3V 8-bit": 0x00000000-0x03a00000 : "rootfs (ro)" Add SSFTL support 0x03a00000-0x04000000 : "config (rw)" 0x04000000-0x04000000 : "additional" mtd: partition "additional" is out of reach -- disabled mmcblk0: mmc0:0001 064MB 1013504KiB mmcblk0:<5>0x00000000-0x04000000 : "whole NAND" p1 p2 pxa27x_udc: version 01-01-2006 ether gadget: using random self ethernet address ether gadget: using random host ethernet address usb0: Ethernet Gadget, version: May Day 2005 usb0: using pxa27x_udc, OUT ep2out-bulk IN ep1in-bulk STATUS ep3in- intr usb0: MAC 72:52:c5:60:bd:ba usb0: HOST MAC 56:28:f6:9d:7e:54 usb0: RNDIS ready wm97xx: Version 0.64 [EMAIL PROTECTED] Advanced Linux Sound Architecture Driver Version 1.0.13 (Tue Nov 28 14:07:24 2006 UTC). AC97 for PXA255 registered pxa2xx-ac97: reset wm97xx: Detected a WM9712 codec input: wm97xx touchscreen as /class/input/input0 wm97xx: setting pen detect pull-up to 16000 Ohms wm97xx: setting adc sample delay to 42 u Secs. WM97XX: Vbat = 4.1V WM97XX: Vref = 2.0V ALSA device list: #0: pxa2xx-ac97 (Wolfson WM9711,WM9712) TCP cubic registered NET: Registered protocol family 1 HSPM init started HSPM driver is loaded and configured VFS: Mounted root (ext2 filesystem) readonly. Freeing init memory: 204K init: HOW ARE YOU GENTLEMEN init: reading config file Thats it...Nothing else happens. Any ideas...?? Thanks for help. --~--~---------~--~----~------------~-------~--~----~ You received this message because you are subscribed to the Google Groups "Android Developers" group. To post to this group, send email to android-developers@googlegroups.com To unsubscribe from this group, send email to [EMAIL PROTECTED] Announcing the new M5 SDK! http://android-developers.blogspot.com/2008/02/android-sdk-m5-rc14-now-available.html For more options, visit this group at http://groups.google.com/group/android-developers?hl=en -~----------~----~----~----~------~----~------~--~---
