Just to follow-up on the USSD messaging, I'm seeing radio log messages
like this:
D/AT ( 829): MUX[primary]: AT< +CUSD:
0,"546865206C617374207472616E73616374696F6E20636F737420302E3030205553442E20596F7572206163636F756E742062616C616E63652069732031302E3530205553442E",15
along with a dialog displaying the same hex string. That message decodes to:
"The last transaction cost 0.00 USD. Your account balance is 10.50 USD."
So I'd say you're just almost done.
Jim
On Mon, Mar 2, 2009 at 3:35 PM, Michael Trimarchi
<trimar...@gandalf.sssup.it> wrote:
> Hi,
>
> Harry Mutch wrote:
>>
>> Hi Michael
>>
>> Tried the ril.so you sent with 14.3fs. This time I got a pop-up with
>> "Connection problem or invalid MMI code". I've attached a dump of the
>> laogcat radio output - there's a lot of it.
>>
>> I've just seen your post about 14.5fs, I'll give that a try now.
>>
>>
>
> I have some good result on gprs too. Maybe Cedric you can go to run again
> without loose call?
> Michael
>
>> BR
>> Aitch
>>
>>
>> 2009/3/2 Harry Mutch <hmu...@gmail.com>:
>>
>>>
>>> OK Michael, I will try it out this evening. Any way forward with the
>>> GPRS issues?
>>>
>>> Aitch
>>>
>>> 2009/3/2 Michael Trimarchi <trimar...@gandalf.sssup.it>:
>>>
>>>>
>>>> Hi,
>>>>
>>>> Michael Trimarchi wrote:
>>>>
>>>>>
>>>>> Hi,
>>>>>
>>>>> Harry Mutch wrote:
>>>>>
>>>>>>
>>>>>> Since there appears to be more functionality with Sean's changes I
>>>>>> tried using USSD. Here's what happens when I send *150# from the
>>>>>> phone. This should fetch the balance on my account::
>>>>>>
>>>>>> D/RILJ ( 876): [2270]> SIGNAL_STRENGTH
>>>>>> D/RIL ( 829): onRequest: SIGNAL_STRENGTH
>>>>>> D/AT ( 829): MUX[primary]: AT> AT+CSQ
>>>>>> D/AT ( 829): MUX[primary]: AT< +CSQ: 21,99
>>>>>> D/AT ( 829): MUX[primary]: AT< OK
>>>>>> D/RILJ ( 876): [2270]< SIGNAL_STRENGTH {21, 99}
>>>>>> D/RILJ ( 876): [2271]> SEND_USSD *150#
>>>>>> D/RIL ( 829): onRequest: SEND_USSD
>>>>>> D/AT ( 829): MUX[primary]: AT> AT+CUSD=1,"*150#",15
>>>>>> D/AT ( 829): MUX[primary]: AT< OK
>>>>>> D/RILJ ( 876): [2271]< SEND_USSD
>>>>>> D/AT ( 829): MUX[primary]: AT< +CUSD: 4
>>>>>> D/RILJ ( 876): [2272]> SIGNAL_STRENGTH
>>>>>> D/RIL ( 829): onRequest: SIGNAL_STRENGTH
>>>>>> D/AT ( 829): MUX[primary]: AT> AT+CSQ
>>>>>> D/AT ( 829): MUX[primary]: AT< +CSQ: 21,99
>>>>>> D/AT ( 829): MUX[primary]: AT< OK
>>>>>> D/RILJ ( 876): [2272]< SIGNAL_STRENGTH {21, 99}
>>>>>>
>>>>>> Long wait with "USSD code running..." po-up showing. Neither "back"
>>>>>> or "menu" buttons do anything, but "home" works and gives the
>>>>>> following:
>>>>>>
>>>>>
>>>>> I will fix today. Michael... I introduce two function from Sean
>>>>> repository. And if you
>>>>> take a look of the code there are some fix that are similar to my
>>>>> repository.
>>>>>
>>>>> Michael
>>>>> _______________________________________________
>>>>> android-freerunner mailing list
>>>>> android-freerunner@android.koolu.org
>>>>> http://android.koolu.org/listinfo.cgi/android-freerunner-koolu.org
>>>>>
>>>>>
>>>>
>>>> Can you try this one?
>>>>
>>>>
>>>> _______________________________________________
>>>> android-freerunner mailing list
>>>> android-freerunner@android.koolu.org
>>>> http://android.koolu.org/listinfo.cgi/android-freerunner-koolu.org
>>>>
>>>>
>>>>
>>>
>>> ------------------------------------------------------------------------
>>>
>>> _______________________________________________
>>> android-freerunner mailing list
>>> android-freerunner@android.koolu.org
>>> http://android.koolu.org/listinfo.cgi/android-freerunner-koolu.org
>
> _______________________________________________
> android-freerunner mailing list
> android-freerunner@android.koolu.org
> http://android.koolu.org/listinfo.cgi/android-freerunner-koolu.org
>
_______________________________________________
android-freerunner mailing list
android-freerunner@android.koolu.org
http://android.koolu.org/listinfo.cgi/android-freerunner-koolu.org
