hello all,

This is Anil, i am very new to this group. when i try to port my
eclair into my devkit8000 board i am getting the following log
messages.please help me in this reguard.

the logcat message are as follows

reading uImage

2167832 bytes read
## Booting kernel from Legacy Image at 80200000 ...
   Image Name:   Linux-2.6.29-omap1
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    2167768 Bytes =  2.1 MB
   Load Address: 80008000
   Entry Point:  80008000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK
OK

Starting kernel ...

Uncompressing
Linux............................................................................................................................................
done, booting the kernel.
Linux version 2.6.29-omap1 (r...@trng-desktop) (gcc version 4.3.3
(Sourcery G++ Lite 2009q1-203) ) #5 Thu Mar 25 13:35:36 IST 2010
CPU: ARMv7 Processor [411fc083] revision 3 (ARMv7), cr=10c5387f
CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
Machine: OMAP3 Beagle Board
Memory policy: ECC disabled, Data cache writeback
L2 CACHE is enabled in bootloader
OMAP3430 ES3.1
SRAM: Mapped pa 0x40200000 to va 0xfc800000 size: 0x100000
Reserving 16777216 bytes SDRAM for VRAM
Built 1 zonelists in Zone order, mobility grouping on.  Total pages:
32512
Kernel command line: console=ttyS2,115200n8 noinitrd root=/dev/
mmcblk0p2 omapdss.def_disp=4.3inch_lcd init=/init rootfstype=ext3 rw
rootdelay=1 nohz=off
Clocking rate (Crystal/DPLL/ARM core): 26.0/266/500 MHz
Reprogramming SDRC
dpll3_m2_clk rate change failed: -22
GPMC revision 5.0
IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96 interrupts
Total of 96 interrupts on 1 active controller
OMAP34xx GPIO hardware version 2.5
PID hash table entries: 512 (order: 9, 2048 bytes)
OMAP clockevent source: GPTIMER12 at 32768 Hz
Console: colour dummy device 80x30
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 128MB = 128MB total
Memory: 108500KB available (3980K code, 723K data, 168K init)
Calibrating delay loop... 491.57 BogoMIPS (lpj=1921024)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
net_namespace: 520 bytes
regulator: core version 0.5
NET: Registered protocol family 16
Found NAND on CS0
Registering NAND on CS0
OMAP DMA hardware revision 4.0
bio: create slab <bio-0> at 0
i2c_omap i2c_omap.1: bus 1 rev3.12 at 2600 kHz
twl4030: PIH (irq 7) chaining IRQs 368..375
twl4030: power (irq 373) chaining IRQs 376..383
twl4030: gpio (irq 368) chaining IRQs 384..401
beagle_twl_gpio_setup:246
twl4030_mmc_init:367
twl4030_mmc_init:382
regulator: VMMC1: 1850 <--> 3150 mV normal standby
regulator: VDAC: 1800 mV normal standby
regulator: VUSB1V5: 1500 <--> 0 mV normal standby
regulator: VUSB1V8: 1800 <--> 0 mV normal standby
regulator: VUSB3V1: 3100 <--> 0 mV normal standby
regulator: VPLL2: 1800 mV normal standby
regulator: VSIM: 1800 <--> 3000 mV normal standby
i2c_omap i2c_omap.3: bus 3 rev3.12 at 100 kHz
SCSI subsystem initialized
twl4030_usb twl4030_usb: Initialized TWL4030 USB module
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Bluetooth: Core ver 2.15
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
musb_hdrc: version 6.0, musb-dma, host, debug=0
musb_hdrc: USB Host mode controller at fa0ab000 using DMA, IRQ 92
musb_hdrc musb_hdrc: MUSB HDRC host driver
musb_hdrc musb_hdrc: new USB bus registered, assigned bus number 1
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: MUSB HDRC host driver
usb usb1: Manufacturer: Linux 2.6.29-omap1 musb-hcd
usb usb1: SerialNumber: musb_hdrc
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
NET: Registered protocol family 1
NetWinder Floating Point Emulator V0.97 (double precision)
ashmem: initialized
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
msgmni has been set to 212
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
OMAP DSS rev 2.0
OMAP DISPC rev 3.0
OMAP VENC rev 2
Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
serial8250.0: ttyS0 at MMIO 0x4806a000 (irq = 72) is a ST16654
serial8250.0: ttyS1 at MMIO 0x4806c000 (irq = 73) is a ST16654
serial8250.0: ttyS2 at MMIO 0x49020000 (irq = 74) is a ST16654
console [ttyS2] enabled
brd: module loaded
loop: module loaded
dm9000 Ethernet Driver, V1.31
Linux video capture interface: v2.00
i2c /dev entries driver
Driver 'sd' needs updating - please use bus_type methods
omap2-nand driver initializing
NAND device: Manufacturer ID: 0x2c, Chip ID: 0xb1 (Micron NAND 128MiB
1,8V 16-bit)
cmdlinepart partition parsing not available
Creating 5 MTD partitions on "omap2-nand":
0x000000000000-0x000000080000 : "X-Loader"
0x000000080000-0x000000260000 : "U-Boot"
0x000000260000-0x000000280000 : "U-Boot Env"
0x000000280000-0x000000680000 : "Kernel"
0x000000680000-0x000008000000 : "File System"
usbmon: debugfs is not available
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-omap ehci-omap.0: OMAP-EHCI Host Controller
ehci-omap ehci-omap.0: new USB bus registered, assigned bus number 2
ehci-omap ehci-omap.0: irq 77, io mem 0x48064800
ehci-omap ehci-omap.0: USB 2.0 started, EHCI 1.00
usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: OMAP-EHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.29-omap1 ehci_hcd
usb usb2: SerialNumber: ehci-omap.0
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
udc: OMAP UDC driver, version: 4 October 2004 (iso) (dma)
android init
input: gpio-keys as /devices/platform/gpio-keys/input/input0
twl4030_rtc twl4030_rtc: rtc core: registered twl4030_rtc as rtc0
twl4030_rtc twl4030_rtc: Power up reset detected.
twl4030_rtc twl4030_rtc: Enabling TWL4030-RTC.
Bluetooth: Virtual HCI driver ver 1.2
Bluetooth: HCI UART driver ver 2.2
Bluetooth: HCI H4 protocol initialized
Bluetooth: HCI BCSP protocol initialized
Bluetooth: HCILL protocol initialized
Bluetooth: Broadcom Blutonium firmware driver ver 1.2
usbcore: registered new interface driver bcm203x
Bluetooth: Digianswer Bluetooth USB driver ver 0.10
usbcore: registered new interface driver bpa10x
Bluetooth: BlueFRITZ! USB driver ver 1.2
usbcore: registered new interface driver bfusb
Bluetooth: Generic Bluetooth USB driver ver 0.5
usbcore: registered new interface driver btusb
Bluetooth: Generic Bluetooth SDIO driver ver 0.1
Registered led device: beagleboard::usr0
Registered led device: beagleboard::usr1
Registered led device: beagleboard::pmu_stat
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
logger: created 64K log 'log_main'
logger: created 256K log 'log_events'
logger: created 64K log 'log_radio'
Advanced Linux Sound Architecture Driver Version 1.0.18a.
No device for DAI twl4030
No device for DAI twl4030 Voice
No device for DAI twl4030 Clock
No device for DAI omap-mcbsp-dai-0
No device for DAI omap-mcbsp-dai-1
No device for DAI omap-mcbsp-dai-2
No device for DAI omap-mcbsp-dai-3
No device for DAI omap-mcbsp-dai-4
OMAP3 Beagle SoC init
TWL4030 Audio Codec init
asoc: twl4030 <-> omap-mcbsp-dai-0 mapping ok
ALSA device list:
  #0: omap3beagle (twl4030)
TCP cubic registered
NET: Registered protocol family 17
NET: Registered protocol family 15
Bluetooth: L2CAP ver 2.13
Bluetooth: L2CAP socket layer initialized
Bluetooth: SCO (Voice Link) ver 0.6
Bluetooth: SCO socket layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM ver 1.11
Bluetooth: BNEP (Ethernet Emulation) ver 1.3
Bluetooth: BNEP filters: protocol multicast
Bluetooth: HIDP (Human Interface Emulation) ver 1.2
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
Power Management for TI OMAP3.
VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev
1
Console: switching to colour frame buffer device 80x30
mmc0: new SD card at address e624
mmcblk0: mmc0:e624 SD01G 968 MiB
 mmcblk0:<4>omapdss DPI: Could not find exact pixel clock. Requested
23500 kHz, got 24000 kHz
 p1 p2
twl4030_rtc twl4030_rtc: setting system clock to 2000-01-01 00:00:00
UTC (946684800)
Waiting 1sec before mounting root device...
VP1:TRANXDONE timeout exceeded going ahead with                  the t2 smps 
wait
VP1:TRANXDONE timeout exceeded going ahead with                  the t2 smps 
wait
kjournald starting.  Commit interval 5 seconds
EXT3-fs warning: maximal mount count reached, running e2fsck is
recommended
EXT3 FS on mmcblk0p2, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) on device 179:2.
Freeing init memory: 168K
Warning: unable to open an initial console.
init: cannot open '/initlogo.rle'
init: Unable to open persistent property directory /data/property
errno: 2
init: cannot find '/system/bin/playmp3', disabling 'bootsound'
init: cannot find '/system/etc/install-recovery.sh', disabling
'flash_recovery'
sh: can't access tty; job control turned off
# warning: `rild' uses 32-bit capabilities (legacy support in use)
init: untracked pid 773 exited
init: untracked pid 787 exited
VP1:TRANXDONE timeout exceeded going ahead with                  the t2 smps 
wait
VP1:TRANXDONE timeout exceeded going ahead with                  the t2 smps 
wait
logcat &
# VP1:TRANXDONE timeout exceeded going ahead with                        the t2 
smps wait
init: untracked pid 799 exited
I/DEBUG   (  770): debuggerd: Mar 24 2010 18:19:16
I/vold    (  768): Android Volume Daemon version 2.0
W/libdbus (  774): Failed to start message bus: Failed to open "/etc/
dbus.conf": Permission denied
E/keystore(  778): chdir: /data/misc/keystore: No such file or
directory
E/vold    (  768): Unable to chdir to /sys/class/mmc_host/mmc0/
slot_name (Not a directory)
E/vold    (  768): Error bootstrapping card '/sys/class/mmc_host/mmc0/
slot_name' (Not a directory)
I/vold    (  768): New MMC card 'SD01G' (serial 1356943616) added @ /
devices/platform/mmci-omap-hs.0/mmc_host/mmc0/mmc0:e624
I/vold    (  768): Disk (blkdev 179:0), 1984000 secs (968 MB) 2
partitions
I/vold    (  768): New blkdev 179.0 on media SD01G, media path /
devices/platform/mmci-omap-hs.0/mmc_host/mmc0/mmc0:e624, Dpp 2
I/vold    (  768): Partition (blkdev 179:1), 819252 secs (400 MB) type
0xc
I/vold    (  768): New blkdev 179.1 on media SD01G, media path /
devices/platform/mmci-omap-hs.0/mmc_host/mmc0/mmc0:e624, Dpp 1
I/vold    (  768): Partition (blkdev 179:2), 1156680 secs (564 MB)
type 0x83
I/vold    (  768): New blkdev 179.2 on media SD01G, media path /
devices/platform/mmci-omap-hs.0/mmc_host/mmc0/mmc0:e624, Dpp 0
D/vold    (  768): Bootstrapping complete
D/AndroidRuntime(  772):
D/AndroidRuntime(  772): >>>>>>>>>>>>>> AndroidRuntime START
<<<<<<<<<<<<<<
D/AndroidRuntime(  772): CheckJNI is ON
E/dalvikvm(  772): Can't open dex cache '/data/dalvik-cache/
sys...@framework@core....@classes.dex': No such file or directory
I/dalvikvm(  772): Unable to open or create cache for /system/
framework/core.jar (/data/dalvik-cache/
sys...@framework@core....@classes.dex)
D/dalvikvm(  772): Unable to process classpath element '/system/
framework/core.jar'
E/dalvikvm(  772): Can't open dex cache '/data/dalvik-cache/
sys...@framework@ext....@classes.dex': No such file or directory
I/dalvikvm(  772): Unable to open or create cache for /system/
framework/ext.jar (/data/dalvik-cache/
sys...@framework@ext....@classes.dex)
D/dalvikvm(  772): Unable to process classpath element '/system/
framework/ext.jar'
E/dalvikvm(  772): Can't open dex cache '/data/dalvik-cache/
sys...@framework@framework....@classes.dex': No such file or directory
I/dalvikvm(  772): Unable to open or create cache for /system/
framework/framework.jar (/data/dalvik-cache/
sys...@framework@framework....@classes.dex)
D/dalvikvm(  772): Unable to process classpath element '/system/
framework/framework.jar'
E/dalvikvm(  772): Can't open dex cache '/data/dalvik-cache/
sys...@framework@android.policy....@classes.dex': No such file or
directory
I/dalvikvm(  772): Unable to open or create cache for /system/
framework/android.policy.jar (/data/dalvik-cache/
sys...@framework@android.policy....@classes.dex)
D/dalvikvm(  772): Unable to process classpath element '/system/
framework/android.policy.jar'
E/dalvikvm(  772): Can't open dex cache '/data/dalvik-cache/
sys...@framework@services....@classes.dex': No such file or directory
I/dalvikvm(  772): Unable to open or create cache for /system/
framework/services.jar (/data/dalvik-cache/
sys...@framework@services....@classes.dex)
D/dalvikvm(  772): Unable to process classpath element '/system/
framework/services.jar'
E/dalvikvm(  772): ERROR: no valid entries found in bootclasspath '/
system/framework/core.jar:/system/framework/ext.jar:/system/framework/
framework.jar:/system/framework/android.policy.jar:/system/framework/
services.jar'
D/dalvikvm(  772): VM cleaning up
D/dalvikvm(  772): LinearAlloc 0x0 used 4100 of 5242880 (0%)
W/dalvikvm(  772): JNI_CreateJavaVM failed
E/AndroidRuntime(  772): JNI_CreateJavaVM failed
I/        (  787): ServiceManager: 0xad08
W/AudioHardwareInterface(  787): Using stubbed audio hardware. No
sound will be produced.
D/AudioHardwareInterface(  787): setMode(NORMAL)
I/CameraService(  787): CameraService started: pid=787
I/AudioFlinger(  787): AudioFlinger's thread 0xb370 ready to run
E/keystore(  794): chdir: /data/misc/keystore: No such file or
directory
W/libdbus (  793): Failed to start message bus: Failed to open "/etc/
dbus.conf": Permission denied
D/AndroidRuntime(  792):
D/AndroidRuntime(  792): >>>>>>>>>>>>>> AndroidRuntime START
<<<<<<<<<<<<<<
D/AndroidRuntime(  792): CheckJNI is ON
E/dalvikvm(  792): Can't open dex cache '/data/dalvik-cache/
sys...@framework@core....@classes.dex': No such file or directory
I/dalvikvm(  792): Unable to open or create cache for /system/
framework/core.jar (/data/dalvik-cache/
sys...@framework@core....@classes.dex)

-- 
unsubscribe: android-kernel+unsubscr...@googlegroups.com
website: http://groups.google.com/group/android-kernel

To unsubscribe from this group, send email to 
android-kernel+unsubscribegooglegroups.com or reply to this email with the 
words "REMOVE ME" as the subject.

Reply via email to