I added some more debug prints and noticed that the engine state is in PREPARING state (while it should ideally be in STARTED state). From the below log, it looks like the Start( ) command didn't complete (coz I don't see a command complete message for this):
************************** PVLOG:TID(0xcb308):Time=2655:PVMediaOutputNode::DoStart E/ ( 836): HV: PVMediaOutputNode::SendMioRequest, aRequest = 4 E/ ( 836): HV: PVMediaOutputNode::SendMioRequest, case EStart E/ ( 836): HV: PVMediaOutputNode::SendMioRequest, Calling iMIOControl->Start() E/PV ( 836): PVLOG:TID(0xcb308):Time=2655:AndroidSurfaceOutput::Start() called E/PV ( 836): PVLOG:TID(0xcb308):Time=2655:PVMediaOutputNode:SendMIORequest: Command Issued to MIO component, waiting on response... *************************** Any idea what I'm missing here? Best regards HV On Jul 14, 3:43 pm, HV <harishv.athr...@gmail.com> wrote: > RockNCode, > > Initially I had this wrong as I was updating in ms. Later, I checked > out the s/w decoder for its implementation (which just slaps the input > PTS onto the output buffer) and did the same. But this hasn't helped > either, here is the dump: > > FetchOutput is complete, nFilledLen = 195840 PTS = 0 > FetchOutput is complete, nFilledLen = 195840 PTS = 34000 > FetchOutput is complete, nFilledLen = 195840 PTS = 67000 > FetchOutput is complete, nFilledLen = 195840 PTS = 100000 > FetchOutput is complete, nFilledLen = 195840 PTS = 134000 > FetchOutput is complete, nFilledLen = 195840 PTS = 167000 > FetchOutput is complete, nFilledLen = 195840 PTS = 200000 > FetchOutput is complete, nFilledLen = 195840 PTS = 234000 > FetchOutput is complete, nFilledLen = 195840 PTS = 267000 > FetchOutput is complete, nFilledLen = 195840 PTS = 300000 > FetchOutput is complete, nFilledLen = 195840 PTS = 334000 > FetchOutput is complete, nFilledLen = 195840 PTS = 367000 > FetchOutput is complete, nFilledLen = 195840 PTS = 400000 > FetchOutput is complete, nFilledLen = 195840 PTS = 434000 > FetchOutput is complete, nFilledLen = 195840 PTS = 467000 > FetchOutput is complete, nFilledLen = 195840 PTS = 500000 > FetchOutput is complete, nFilledLen = 195840 PTS = 534000 > FetchOutput is complete, nFilledLen = 195840 PTS = 567000 > FetchOutput is complete, nFilledLen = 195840 PTS = 600000 > FetchOutput is complete, nFilledLen = 195840 PTS = 634000 > FetchOutput is complete, nFilledLen = 195840 PTS = 667000 > FetchOutput is complete, nFilledLen = 195840 PTS = 700000 > FetchOutput is complete, nFilledLen = 195840 PTS = 734000 > FetchOutput is complete, nFilledLen = 195840 PTS = 767000 > FetchOutput is complete, nFilledLen = 195840 PTS = 800000 > FetchOutput is complete, nFilledLen = 195840 PTS = 834000 > FetchOutput is complete, nFilledLen = 195840 PTS = 867000 > FetchOutput is complete, nFilledLen = 195840 PTS = 900000 > FetchOutput is complete, nFilledLen = 195840 PTS = 934000 > FetchOutput is complete, nFilledLen = 195840 PTS = 967000 > FetchOutput is complete, nFilledLen = 195840 PTS = 1000000 > FetchOutput is complete, nFilledLen = 195840 PTS = 1034000 > > On Jul 13, 9:50 pm, RockNCode <alexgarci...@gmail.com> wrote: > > > > > Hi. > > > Have you printed you buffer timestamp values ? I've seen similar > > issues when there is a problem with AV sync, probably your timestamp > > resolution does not match PV's (it should be in microseconds). > > > - Regards. > > > On Jul 13, 8:02 am, HV <harishv.athr...@gmail.com> wrote: > > > > Thanks Deva for your response. Yep, there are no issues in the > > > underlying decoder/driver. If I hold the display from going into > > > standby, I see prints all the way thru end-of-stream. If there were a > > > problem with the overlay, then how is it able to display the 1st > > > frame? Is there a call stack that I can compare against (once the > > > output buffer has been handed over to PV)? > > > > HV > > > > On Jul 12, 8:51 pm, Deva R <r.deva...@gmail.com> wrote: > > > > > If FillBufferDone keeps coming, its a indication that whole playback > > > > cycle > > > > is working (file has been read, decoder has been given > > > > Emptybuffer/fillbuffer calls, got FillBufferDone)., > > > > see what happens in overlay, when u post the buffer to FillBufferDone., > > > > > On Mon, Jul 12, 2010 at 3:13 PM, HV <harishv.athr...@gmail.com> wrote: > > > > > Hi, > > > > > > I've integrated my MPEG-4 hardware enabled decoder with the PVMF and > > > > > implemented the necessary OMX calls. The trouble I'm having now is > > > > > that once I click on the thumbnail within Gallery, the 1st frame shows > > > > > up, but it stops right there!! I see that my driver/decoder is running > > > > > in the background generating interrupts and churning out new YUV > > > > > frames, but Gallery is stuck. I also see that I'm filling in data > > > > > along with the FillBufferDone callback, but see no visual progress. > > > > > Any idea what might be missing here? > > > > > > Thanks in advance > > > > > HV > > > > > > -- > > > > > unsubscribe: > > > > > android-porting+unsubscr...@googlegroups.com<android-porting%2Bunsubscribe@ > > > > > googlegroups.com> > > > > > website:http://groups.google.com/group/android-porting -- unsubscribe: android-porting+unsubscr...@googlegroups.com website: http://groups.google.com/group/android-porting
