Srinidhi tryout the following link. http://coredruids.org/demos/Android_Froyo_Hawkboard_01-OCT-2010.tar.bz2
On Mon, Nov 15, 2010 at 1:17 PM, Srinidhi K V <srinidh...@yahoo.co.in>wrote: > Thanks for the reply Sayiram, No I was not aware of availability of 2.6.35 > kernel for Hawkboard. I tried google it to download but could not find it. > can you please provide download link / command to pull it from git > > Thanks > Srinidhi KV > > > On Sun, Nov 14, 2010 at 9:32 PM, Sayiram K N > <sayiram.koth...@gmail.com>wrote: > >> Hi have u tried the kernel 2.6.35 whicj is releasded along with the froyo >> from hawkboard >> >> On Nov 14, 2010 12:22 PM, "Srinidhi K V" <srinidh...@yahoo.co.in> >> wrote: >> >> Hi All, >> >> I am trying to bring up Froyo on Hawk board. But I am hitting an issue, >> after Kernel boots I have an error popping up "LAUNCH FAILED FORCE CLOSE". >> I am using Core Druid's Kernel and File system >> Boot argument I am using is >> bootargs=mem=128M console=ttyS2,115200n8 noinitrd root=/dev/sda1 rootwait >> rw init=/init ip=dhcp androidboot.console=ttyS2 >> >> Can anyone provide pointers on what is the issue is about and how it can >> be fixed. >> >> The Kernel log is as follows >> >> hawkboard.org > boot >> >> NAND read: device 0 offset 0x200000, size 0x200000 >> 2097152 bytes read: OK >> ## Booting kernel from Legacy Image at c0700000 ... >> Image Name: Linux-2.6.32-rc6-g0e521ee >> Image Type: ARM Linux Kernel Image (uncompressed) >> Data Size: 1958448 Bytes = 1.9 MB >> Load Address: c0008000 >> Entry Point: c0008000 >> Verifying Checksum ... OK >> Loading Kernel Image ... OK >> OK >> >> Starting kernel ... >> >> Linux version 2.6.32-rc6-g0e521ee (r...@sct-desktop) (gcc version 4.3.3 >> (Sourcery G++ Lite 2009q1-203) ) #1 PREEMPT Tue Sep 28 18:16:16 IST 2010 >> CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177 >> CPU: VIVT data cache, VIVT instruction cache >> Machine: OMAPL 138 Hawkboard.org >> Memory policy: ECC disabled, Data cache writeback >> DaVinci da850/omap-l138 variant 0x0 >> Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512 >> Kernel command line: console=ttyS2,115200n8 console=tty1 noinitrd >> root=/dev/mmcblk0p1 rootwait rw init=/init ip=dhcp androidboot.console=ttyS2 >> Unknown boot option `androidboot.console=ttyS2': ignoring >> PID hash table entries: 512 (order: -1, 2048 bytes) >> Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) >> Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) >> Memory: 128MB = 128MB total >> Memory: 125140KB available (3732K code, 726K data, 148K init, 0K highmem) >> SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 >> Hierarchical RCU implementation. >> NR_IRQS:245 >> Console: colour dummy device 80x30 >> Calibrating delay loop... 149.50 BogoMIPS (lpj=747520) >> Mount-cache hash table entries: 512 >> CPU: Testing write buffer coherency: ok >> DaVinci: 144 gpio irqs >> regulator: core version 0.5 >> NET: Registered protocol family 16 >> bio: create slab <bio-0> at 0 >> SCSI subsystem initialized >> usbcore: registered new interface driver usbfs >> usbcore: registered new interface driver hub >> usbcore: registered new device driver usb >> Switching to clocksource timer0_1 >> musb_hdrc: version 6.0, cppi4.1-dma, (host+peripheral), debug=0 >> Waiting for USB PHY clock good... >> musb_hdrc: USB OTG mode controller at fee00000 using DMA, IRQ 58 >> musb_hdrc musb_hdrc: MUSB HDRC host driver >> musb_hdrc musb_hdrc: new USB bus registered, assigned bus number 1 >> usb usb1: configuration #1 chosen from 1 choice >> hub 1-0:1.0: USB hub found >> hub 1-0:1.0: 1 port detected >> NET: Registered protocol family 2 >> IP route cache hash table entries: 1024 (order: 0, 4096 bytes) >> TCP established hash table entries: 4096 (order: 3, 32768 bytes) >> TCP bind hash table entries: 4096 (order: 2, 16384 bytes) >> TCP: Hash tables configured (established 4096 bind 4096) >> TCP reno registered >> NET: Registered protocol family 1 >> RPC: Registered udp transport module. >> RPC: Registered tcp transport module. >> RPC: Registered tcp NFSv4.1 backchannel transport module. >> ashmem: initialized >> JFFS2 version 2.2. (NAND) �© 2001-2006 Red Hat, Inc. >> msgmni has been set to 244 >> io scheduler noop registered >> io scheduler anticipatory registered (default) >> da8xx_lcdc da8xx_lcdc.0: GLCD: Found VGA_Monitor panel >> Console: switching to colour frame buffer device 80x30 >> Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled >> serial8250.0: ttyS0 at MMIO 0x1c42000 (irq = 25) is a 16550A >> serial8250.0: ttyS1 at MMIO 0x1d0c000 (irq = 53) is a 16550A >> serial8250.0: ttyS2 at MMIO 0x1d0d000 (irq = 61) is a 16550A >> console [ttyS2] enabled >> brd: module loaded >> ahci ahci: forcing PORTS_IMPL to 0x1 >> ahci ahci: AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl SATA mode >> ahci ahci: flags: ncq sntf pm led clo only pmp pio slum part ccc >> scsi0 : ahci >> ata1: SATA max UDMA/133 irq 67 >> NAND device: Manufacturer ID: 0x2c, Chip ID: 0xa1 (Micron NAND 128MiB 1,8V >> 8-bit) >> Bad block table not found for chip 0 >> Bad block table not found for chip 0 >> Scanning device for bad blocks >> Creating 5 MTD partitions on "davinci_nand.1": >> 0x000000000000-0x000000020000 : "u-boot env" >> 0x000000020000-0x000000040000 : "UBL" >> 0x000000040000-0x0000000c0000 : "u-boot" >> 0x000000200000-0x000000400000 : "kernel" >> 0x000000400000-0x000008000000 : "filesystem" >> davinci_nand davinci_nand.1: controller rev. 2.5 >> console [netcon0] enabled >> netconsole: network logging started >> ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver >> ohci ohci.0: DA8xx OHCI >> ohci ohci.0: new USB bus registered, assigned bus number 2 >> ohci ohci.0: irq 59, io mem 0x01e25000 >> usb usb2: configuration #1 chosen from 1 choice >> hub 2-0:1.0: USB hub found >> hub 2-0:1.0: 1 port detected >> Initializing USB Mass Storage driver... >> usbcore: registered new interface driver usb-storage >> USB Mass Storage support registered. >> g_ether gadget: using random self ethernet address >> g_ether gadget: using random host ethernet address >> usb0: MAC 76:4a:d8:59:43:9b >> usb0: HOST MAC ee:4b:3c:34:2d:54 >> g_ether gadget: Ethernet Gadget, version: Memorial Day 2008 >> g_ether gadget: g_ether ready >> mice: PS/2 mouse device common for all mice >> i2c /dev entries driver >> watchdog watchdog: heartbeat 60 sec >> cpuidle: using governor ladder >> cpuidle: using governor menu >> davinci_mmc davinci_mmc.0: Using DMA, 4-bit mode >> usbcore: registered new interface driver usbhid >> usbhid: v2.6:USB HID core driver >> logger: created 64K log 'log_main' >> logger: created 256K log 'log_events' >> logger: created 64K log 'log_radio' >> logger: created 64K log 'log_system' >> Advanced Linux Sound Architecture Driver Version 1.0.21. >> No device for DAI tlv320aic3x >> asoc: tlv320aic3x <-> davinci-i2s mapping ok >> ALSA device list: >> #0: DA850/OMAP-L138 EVM (tlv320aic3x) >> mmc0: new high speed SD card at address b368 >> mmcblk0: mmc0:b368 SDC 1.85 GiB >> ata1: SATA link down (SStatus 0 SControl 300) >> TCP cubic registered >> NET: Registered protocol family 17 >> Clocks: disable unused emac >> Clocks: disable unused spi1 >> mmcblk0: p1 >> davinci_emac_probe: using random MAC addr: a6:ab:b0:80:73:2e >> emac-mii: probed >> usb 2-1: new low speed USB device using ohci and address 2 >> usb 2-1: configuration #1 chosen from 1 choice >> input: Logitech USB Keyboard as >> /devices/platform/ohci.0/usb2/2-1/2-1:1.0/input/input0 >> generic-usb 0003:046D:C31C.0001: input: USB HID v1.10 Keyboard [Logitech >> USB Keyboard] on usb-ohci.0-1/input0 >> input: Logitech USB Keyboard as >> /devices/platform/ohci.0/usb2/2-1/2-1:1.1/input/input1 >> generic-usb 0003:046D:C31C.0002: input: USB HID v1.10 Device [Logitech USB >> Keyboard] on usb-ohci.0-1/input1 >> eth0: attached PHY driver [Generic PHY] (mii_bus:phy_addr=1:07, id=7c0f1) >> IP-Config: Incomplete network configuration information. >> kjournald starting. Commit interval 5 seconds >> EXT3 FS on mmcblk0p1, internal journal >> EXT3-fs: recovery complete. >> EXT3-fs: mounted filesystem with writeback data mode. >> VFS: Mounted root (ext3 filesystem) on device 179:1. >> Freeing init memory: 148K >> Warning: unable to open an initial console. >> init: cannot open '/initlogo.rle' >> init: cannot find '/system/etc/install-recovery.sh', disabling >> 'flash_recovery' >> # warning: `rild' uses 32-bit capabilities (legacy support in use) >> binder: release 774:774 transaction 1502 out, still active >> binder: 689:689 transaction failed 29189, size 4-0 >> binder: send failed reply for transaction 1502, target dead >> -------------------------------------------BOOT STOPS >> HERE----------------------------------------------------------------- >> >> Thanks >> Srinidhi KV >> >> -- >> unsubscribe: >> android-porting+unsubscr...@googlegroups.com<android-porting%2bunsubscr...@googlegroups.com> >> website: http://groups.google.com/group/android-porting >> >> > -- unsubscribe: android-porting+unsubscr...@googlegroups.com website: http://groups.google.com/group/android-porting
