Hi Deepak, I has the same issue while porting Froyo on Hawkboard. I had flashed the kernel to NAND, I erased it and reflashed it to NAND and this did the trick. I am not sure it will work, but you can give a try.
Thanks Srinidhi On Fri, Dec 24, 2010 at 2:17 PM, deepak singal <deesin...@gmail.com> wrote: > Hi All, > > I am trying to port gingerbread on omapevm3530 based target board using > latest gingerbread source code and rowboat fyoro kernel 2.6.32. > I have checked out the latest source code and built android root file > system and kernel. > <http://git.android-x86.org/> > I am facing below kernel panic -- > > ## Booting image at 80000000 ... > Image Name: Linux-2.6.32 > Image Type: ARM Linux Kernel Image (uncompressed) > Data Size: 2407496 Bytes = 2.3 MB > Load Address: 80008000 > Entry Point: 80008000 > Verifying Checksum ... OK > OK > > Starting kernel ... > > Uncompressing > Linux..................................................................................................................................................... > Linux version 2.6.32 (r...@celestial-laptop) (gcc version 4.4.1 (Sourcery > G++ Lite 2010q1-202) ) #6 Fri Dec 24 16:37:18 CST 2010 > CPU: ARMv7 Processor [411fc082] revision 2 (ARMv7), cr=10c53c7f > CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache > Machine: OMAP3 EVM > Memory policy: ECC disabled, Data cache writeback > OMAP3430/3530 ES2.1 (l2cache iva sgx neon isp ) > SRAM: Mapped pa 0x40200000 to va 0xfe400000 size: 0x100000 > Reserving 4194304 bytes SDRAM for VRAM > Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512 > Kernel command line: console=ttyS0,115200n8 root=/dev/mmcblk0p2 > androidboot.console=ttyS0 rw ip=off devfs=mount init=/init rootdelay=3 > PID hash table entries: 512 (order: -1, 2048 bytes) > Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) > Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) > Memory: 128MB = 128MB total > Memory: 120348KB available (4212K code, 824K data, 168K init, 0K highmem) > Hierarchical RCU implementation. > NR_IRQS:402 > Clocking rate (Crystal/Core/MPU): 26.0/332/500 MHz > Reprogramming SDRC clock to 332000000 Hz > GPMC revision 5.0 > IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96 interrupts > Total of 96 interrupts on 1 active controller > OMAP GPIO hardware version 2.5 > OMAP clockevent source: GPTIMER1 at 32768 Hz > Console: colour dummy device 80x30 > Calibrating delay loop... 499.92 BogoMIPS (lpj=1949696) > Mount-cache hash table entries: 512 > CPU: Testing write buffer coherency: ok > regulator: core version 0.5 > NET: Registered protocol family 16 > omap3evmdc: Driver registration complete > OMAP DMA hardware revision 4.0 > bio: create slab <bio-0> at 0 > SCSI subsystem initialized > usbcore: registered new interface driver usbfs > usbcore: registered new interface driver hub > usbcore: registered new device driver usb > i2c_omap i2c_omap.1: bus 1 rev3.12 at 2600 kHz > twl4030: PIH (irq 7) chaining IRQs 368..375 > twl4030: power (irq 373) chaining IRQs 376..383 > twl4030: gpio (irq 368) chaining IRQs 384..401 > regulator: VMMC1: 1850 <--> 3150 mV normal standby > regulator: VDAC: 1800 mV normal standby > regulator: VAUX2_4030: 1800 mV normal standby > regulator: VPLL2: 1800 mV normal standby > regulator: VSIM: 1800 <--> 3000 mV normal standby > regulator: VUSB1V5: 1500 mV normal standby > regulator: VUSB1V8: 1800 mV normal standby > twl_reg twl_reg.18: can't register VUSB1V8, -16 > twl_reg: probe of twl_reg.18 failed with error -16 > i2c_omap i2c_omap.2: bus 2 rev3.12 at 400 kHz > i2c_omap i2c_omap.3: bus 3 rev3.12 at 400 kHz > Switching to clocksource 32k_counter > musb_hdrc: version 6.0, musb-dma, otg (peripheral+host), debug=0 > musb_hdrc: USB OTG mode controller at fa0ab000 using DMA, IRQ 92 > NET: Registered protocol family 2 > IP route cache hash table entries: 1024 (order: 0, 4096 bytes) > TCP established hash table entries: 4096 (order: 3, 32768 bytes) > TCP bind hash table entries: 4096 (order: 2, 16384 bytes) > TCP: Hash tables configured (established 4096 bind 4096) > TCP reno registered > UDP hash table entries: 256 (order: 0, 4096 bytes) > UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) > NET: Registered protocol family 1 > RPC: Registered udp transport module. > RPC: Registered tcp transport module. > RPC: Registered tcp NFSv4.1 backchannel transport module. > omap-iommu omap-iommu.0: isp registered > OMAP35x Linux PSP version 03.00.01.06 (OMAP3EVM) > NetWinder Floating Point Emulator V0.97 (double precision) > ashmem: initialized > VFS: Disk quotas dquot_6.5.2 > Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) > JFFS2 version 2.2. (NAND) �© 2001-2006 Red Hat, Inc. > msgmni has been set to 235 > alg: No test for stdrng (krng) > io scheduler noop registered > io scheduler deadline registered > io scheduler cfq registered (default) > OMAP DSS rev 2.0 > OMAP DISPC rev 3.0 > OMAP VENC rev 2 > OMAP DSI rev 1.0 > Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled > serial8250.0: ttyS0 at MMIO 0x4806a000 (irq = 72) is a ST16654 > console [ttyS0] enabled > serial8250.1: ttyS1 at MMIO 0x4806c000 (irq = 73) is a ST16654 > serial8250.2: ttyS2 at MMIO 0x49020000 (irq = 74) is a ST16654 > brd: module loaded > loop: module loaded > omap2-nand driver initializing > OneNAND driver initializing > omap2-onenand omap2-onenand: initializing on CS0, phys base 0x20000000, > virtual base c8880000 > Muxed OneNAND 128MB 1.8V 16-bit (0x30) > OneNAND version = 0x0221 > Scanning device for bad blocks > onenand_bbt_wait: ecc error = 0x2222, controller error 0x2400 > Bad eraseblock 676 at 0x05480000 > Creating 5 MTD partitions on "omap2-onenand": > 0x000000000000-0x000000080000 : "xloader-onenand" > 0x000000080000-0x000000260000 : "uboot-onenand" > 0x000000260000-0x000000280000 : "params-onenand" > 0x000000280000-0x000000780000 : "linux-onenand" > 0x000000780000-0x000008000000 : "jffs2-onenand" > smsc911x: Driver version 2008-10-21. > smsc911x-mdio: probed > eth0: attached PHY driver [Generic PHY] (mii_bus:phy_addr=ffffffff:01, > irq=-1) > net eth0: MAC Address: 00:50:c2:7e:88:a4 > usbcore: registered new interface driver cdc_ether > usbcore: registered new interface driver dm9601 > ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver > ehci-omap ehci-omap.0: OMAP-EHCI Host Controller > ehci-omap ehci-omap.0: new USB bus registered, assigned bus number 1 > ehci-omap ehci-omap.0: irq 77, io mem 0x48064800 > ehci-omap ehci-omap.0: USB 2.0 started, EHCI 1.00 > usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 > usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 > usb usb1: Product: OMAP-EHCI Host Controller > usb usb1: Manufacturer: Linux 2.6.32 ehci_hcd > usb usb1: SerialNumber: ehci-omap.0 > hub 1-0:1.0: USB hub found > hub 1-0:1.0: 3 ports detected > Initializing USB Mass Storage driver... > usbcore: registered new interface driver usb-storage > USB Mass Storage support registered. > usbcore: registered new interface driver usbtest > android init > android_probe pdata: c047bac8 > android_bind > android_usb gadget: android_usb ready > musb_hdrc musb_hdrc: MUSB HDRC host driver > musb_hdrc musb_hdrc: new USB bus registered, assigned bus number 2 > usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 > usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 > usb usb2: Product: MUSB HDRC host driver > usb usb2: Manufacturer: Linux 2.6.32 musb-hcd > usb usb2: SerialNumber: musb_hdrc > hub 2-0:1.0: USB hub found > hub 2-0:1.0: 1 port detected > f_adb init > android_register_function adb > adb_bind_config > f_mass_storage init > android_register_function usb_mass_storage > input: TWL4030 Keypad as > /devices/platform/i2c_omap.1/i2c-1/1-004a/twl4030_keypad/input/input0 > ads7846 spi1.0: touchscreen, irq 335 > input: ADS7846 Touchscreen as > /devices/platform/omap2_mcspi.1/spi1.0/input/input1 > using rtc device, twl_rtc, for alarms > twl_rtc twl_rtc: rtc core: registered twl_rtc as rtc0 > twl_rtc twl_rtc: Power up reset detected. > twl_rtc twl_rtc: Enabling TWL-RTC. > i2c /dev entries driver > Linux video capture interface: v2.00 > tvp514x 3-005d: Registered to v4l2 master omap34xxcam!! > omap-iommu omap-iommu.0: isp: version 1.1 > usbcore: registered new interface driver uvcvideo > USB Video Class driver (v0.1.0) > OMAP Watchdog Timer Rev 0x31: initial timeout 60 sec > usbcore: registered new interface driver usbhid > usbhid: USB HID core driver > logger: created 64K log 'log_main' > logger: created 256K log 'log_events' > logger: created 64K log 'log_radio' > logger: created 64K log 'log_system' > Advanced Linux Sound Architecture Driver Version 1.0.21. > usbcore: registered new interface driver snd-usb-audio > No device for DAI omap-mcbsp-dai-0 > No device for DAI omap-mcbsp-dai-1 > No device for DAI omap-mcbsp-dai-2 > No device for DAI omap-mcbsp-dai-3 > No device for DAI omap-mcbsp-dai-4 > OMAP3 EVM SoC init > asoc: twl4030 <-> omap-mcbsp-dai-0 mapping ok > ALSA device list: > #0: omap3evm (twl4030) > TCP cubic registered > NET: Registered protocol family 17 > NET: Registered protocol family 15 > Power Management for TI OMAP3. > Division by zero in kernel. > [<c0038890>] (unwind_backtrace+0x0/0xd0) from [<c017cb5c>] (Ldiv0+0x8/0x10) > Division by zero in kernel. > [<c0038890>] (unwind_backtrace+0x0/0xd0) from [<c017cb5c>] (Ldiv0+0x8/0x10) > SmartReflex driver initialized > VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 1 > twl_rtc twl_rtc: setting system clock to 2000-01-01 00:00:00 UTC > (946684800) > mmc0: new high speed SD card at address b368 > mmcblk0: mmc0:b368 SD02G 1.85 GiB > mmcblk0: p1 p2 > tvp514x 3-005d: chip id mismatch msb:0xfb lsb:0xfb > tvp514x 3-005d: Unable to detect decoder > tvp514x 3-005d: chip id mismatch msb:0xfb lsb:0xfb > tvp514x 3-005d: Unable to detect decoder > tvp514x 3-005d: chip id mismatch msb:0xfb lsb:0xfb > tvp514x 3-005d: Unable to detect decoder > tvp514x 3-005d: chip id mismatch msb:0xfb lsb:0xfb > tvp514x 3-005d: Unable to detect decoder > omapdss DPI error: display already enabled > omap_vout omap_vout: 'lcd' Display already enabled > omapdss DPI error: display already enabled > omap_vout omap_vout: 'lcd' Display already enabled > omap_vout omap_vout: Buffer Size = 3686400 > omap_vout omap_vout: : registered and initialized video device 0 > omap_vout omap_vout: Buffer Size = 3686400 > omap_vout omap_vout: : registered and initialized video device 1 > Waiting 3sec before mounting root device... > kjournald starting. Commit interval 5 seconds > EXT3-fs (mmcblk0p2): using internal journal > EXT3-fs (mmcblk0p2): mounted filesystem with writeback data mode > VFS: Mounted root (ext3 filesystem) on device 179:2. > Freeing init memory: 168K > Warning: unable to open an initial console. > init: cannot open '/initlogo.rle' > Kernel panic - not syncing: Attempted to kill init! > > > Any help will be highly appreciated. > > Thanks & Regards, > Deepak > > -- > unsubscribe: > android-porting+unsubscr...@googlegroups.com<android-porting%2bunsubscr...@googlegroups.com> > website: http://groups.google.com/group/android-porting > -- unsubscribe: android-porting+unsubscr...@googlegroups.com website: http://groups.google.com/group/android-porting
