Hello
I am able to boot the beagle and login as root
then I ifup eth0 and I get an IP
I can not ssh to the beagleboard
The following is the dmesg output
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 3.2.18 (vidal@sim2) (gcc version 4.5.4
20120305 (prerelease) (GCC) ) #1 Sat Jun 16 09:28:42 MDT 2012
[ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7),
cr=10c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing
instruction cache
[ 0.000000] Machine: OMAP3 Beagle Board
[ 0.000000] Beagle expansionboard: none
[ 0.000000] Beagle second expansionboard: none
[ 0.000000] Reserving 16777216 bytes SDRAM for VRAM
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] On node 0 totalpages: 125440
[ 0.000000] free_area_init_node: node 0, pgdat c07e03f0, node_mem_map
c08a0000
[ 0.000000] Normal zone: 1024 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 124416 pages, LIFO batch:31
[ 0.000000] OMAP3630 ES1.2 (l2cache iva sgx neon isp 192mhz_clk )
[ 0.000000] Clocking rate (Crystal/Core/MPU): 26.0/400/600 MHz
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on.
Total pages: 124416
[ 0.000000] Kernel command line: console=tty0 console=ttyO2,115200n8
consoleblank=0 mpurate=auto buddy=none buddy2=none camera=none vram=16M
omapfb.mode=dvi:hd720 omapfb.vram=0:8M,1:4M,2:4M omapdss.def_disp=dvi
root=/dev/mmcblk0p2 ro rootfstype=ext4 rootwait
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144
bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072
bytes)
[ 0.000000] allocated 2097152 bytes of page_cgroup
[ 0.000000] please try 'cgroup_disable=memory' option if you don't want
memory cgroups
[ 0.000000] Memory: 490MB = 490MB total
[ 0.000000] Memory: 486344k/486344k available, 37944k reserved, 0K
highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xe0800000 - 0xf8000000 ( 376 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0008000 - 0xc0741cec (7400 kB)
[ 0.000000] .init : 0xc0742000 - 0xc0788000 ( 280 kB)
[ 0.000000] .data : 0xc0788000 - 0xc07e2710 ( 362 kB)
[ 0.000000] .bss : 0xc07e2734 - 0xc089f854 ( 757 kB)
[ 0.000000] SLUB: Genslabs=11, HWalign=64, Order=0-3, MinObjects=0,
CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:410 nr_irqs:410 410
[ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96
interrupts
[ 0.000000] Total of 96 interrupts on 1 active controller
[ 0.000000] OMAP clockevent source: GPTIMER12 at 32768 Hz
[ 0.000000] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps
every 131071999ms
[ 0.000000] Console: colour dummy device 80x30
[ 0.000000] console [tty0] enabled
[ 0.000610] Calibrating delay loop... 506.27 BogoMIPS (lpj=1978368)
[ 0.039764] pid_max: default: 32768 minimum: 301
[ 0.040008] Security Framework initialized
[ 0.040069] AppArmor: AppArmor initialized
[ 0.040313] Mount-cache hash table entries: 512
[ 0.040740] Initializing cgroup subsys cpuacct
[ 0.040771] Initializing cgroup subsys memory
[ 0.040832] Initializing cgroup subsys devices
[ 0.040863] Initializing cgroup subsys freezer
[ 0.040893] Initializing cgroup subsys blkio
[ 0.040924] Initializing cgroup subsys perf_event
[ 0.041015] CPU: Testing write buffer coherency: ok
[ 0.042083] devtmpfs: initialized
[ 0.045715] print_constraints: dummy:
[ 0.045989] NET: Registered protocol family 16
[ 0.046173] GPMC revision 5.0
[ 0.047637] OMAP GPIO hardware version 2.5
[ 0.048980] omap_mux_init: Add partition: #1: core, flags: 0
[ 0.050262] OMAP3 Beagle Rev: xM C
[ 0.053344] Reprogramming SDRC clock to 400000000 Hz
[ 0.053375] dpll3_m2_clk rate change failed: -22
[ 0.055236] Found NAND on CS0
[ 0.055267] Registering NAND on CS0
[ 0.055603] gpio_request: gpio--22 (DVI reset) status -22
[ 0.055603] Unable to get DVI reset GPIO
[ 0.055755] hw-breakpoint: debug architecture 0x4 unsupported.
[ 0.059265] omap-mcbsp.2: alias fck already exists
[ 0.059478] omap-mcbsp.3: alias fck already exists
[ 0.060668] OMAP DMA hardware revision 5.0
[ 0.067504] bio: create slab<bio-0> at 0
[ 0.068725] SCSI subsystem initialized
[ 0.069915] usbcore: registered new interface driver usbfs
[ 0.070098] usbcore: registered new interface driver hub
[ 0.070281] usbcore: registered new device driver usb
[ 0.071014] omap_i2c omap_i2c.1: bus 1 rev1.4.0 at 2600 kHz
[ 0.073516] twl4030: PIH (irq 7) chaining IRQs 368..375
[ 0.073638] twl4030: power (irq 373) chaining IRQs 376..383
[ 0.074127] twl4030: gpio (irq 368) chaining IRQs 384..401
[ 0.074493] _omap_mux_init_gpio: Could not set gpio192
[ 0.077270] print_constraints: VUSB1V5: 1500 mV normal standby
[ 0.077697] print_constraints: VUSB1V8: 1800 mV normal standby
[ 0.078063] print_constraints: VUSB3V1: 3100 mV normal standby
[ 0.079742] twl4030_usb twl4030_usb: Initialized TWL4030 USB module
[ 0.080505] print_constraints: VMMC1: 1850<--> 3150 mV at 3150 mV
normal standby
[ 0.080963] print_constraints: VDAC: 1800 mV normal standby
[ 0.081359] print_constraints: VAUX2_4030: 1800 mV normal
[ 0.081787] print_constraints: VDVI: 1800 mV normal standby
[ 0.082275] print_constraints: VSIM: 1800<--> 3000 mV at 1800 mV normal
standby
[ 0.082611] omap_i2c omap_i2c.2: bus 2 rev1.4.0 at 400 kHz
[ 0.092803] omap_i2c omap_i2c.3: bus 3 rev1.4.0 at 100 kHz
[ 0.093933] NetLabel: Initializing
[ 0.093963] NetLabel: domain hash size = 128
[ 0.093963] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.094055] NetLabel: unlabeled traffic allowed by default
[ 0.094085] Switching to clocksource 32k_counter
[ 0.107604] AppArmor: AppArmor Filesystem Enabled
[ 0.119964] musb-hdrc: version 6.0, ?dma?, otg (peripheral+host)
[ 0.129516] musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine,
bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn)
[ 0.129547] musb-hdrc: MHDRC RTL version 1.800
[ 0.129577] musb-hdrc: setup fifo_mode 5
[ 0.129577] musb-hdrc: 28/31 max ep, 8192/16384 memory
[ 0.129913] musb-hdrc musb-hdrc: USB OTG mode controller at fa0ab000
using DMA, IRQ 92
[ 0.130279] NET: Registered protocol family 2
[ 0.130615] IP route cache hash table entries: 4096 (order: 2, 16384
bytes)
[ 0.131347] TCP established hash table entries: 16384 (order: 5, 131072
bytes)
[ 0.131744] TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.131958] TCP: Hash tables configured (established 16384 bind 16384)
[ 0.131988] TCP reno registered
[ 0.131988] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.132049] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.132385] NET: Registered protocol family 1
[ 0.132934] RPC: Registered named UNIX socket transport module.
[ 0.132965] RPC: Registered udp transport module.
[ 0.132995] RPC: Registered tcp transport module.
[ 0.132995] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.133422] omap_dsp_init: 600000 bytes @ 9ea00000
[ 0.135040] audit: initializing netlink socket (disabled)
[ 0.135131] type=2000 audit(0.148:1): initialized
[ 0.348327] VFS: Disk quotas dquot_6.5.2
[ 0.348663] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.352325] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 0.352416] fuse init (API version 7.17)
[ 0.354400] Btrfs loaded
[ 0.354461] msgmni has been set to 949
[ 0.355957] Block layer SCSI generic (bsg) driver version 0.4 loaded
(major 253)
[ 0.356109] io scheduler noop registered
[ 0.356140] io scheduler deadline registered
[ 0.356201] io scheduler cfq registered (default)
[ 0.357147] OMAP DSS rev 2.0
[ 0.359985] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 0.361236] omap_uart.0: ttyO0 at MMIO 0x4806a000 (irq = 72) is a OMAP
UART0
[ 0.361541] omap_uart.1: ttyO1 at MMIO 0x4806c000 (irq = 73) is a OMAP
UART1
[ 0.361846] omap_uart.2: ttyO2 at MMIO 0x49020000 (irq = 74) is a OMAP
UART2
[ 1.089782] console [ttyO2] enabled
[ 1.093872] omap_uart.3: ttyO3 at MMIO 0x49042000 (irq = 80) is a OMAP
UART3
[ 1.101898] [drm] Initialized drm 1.1.0 20060810
[ 1.114562] brd: module loaded
[ 1.121948] loop: module loaded
[ 1.128295] twl4030_madc twl4030_madc: clk disabled, enabling
[ 1.136291] omap2-nand driver initializing
[ 1.140991] No NAND device found
[ 1.144714] No NAND device found
[ 1.148345] OneNAND driver initializing
[ 1.153106] usbcore: registered new interface driver cdc_ether
[ 1.159393] usbcore: registered new interface driver rndis_host
[ 1.165740] cdc_ncm: 04-Aug-2011
[ 1.169189] usbcore: registered new interface driver cdc_ncm
[ 1.175628] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 3.195953] ehci-omap ehci-omap.0: OMAP-EHCI Host Controller
[ 3.202239] ehci-omap ehci-omap.0: new USB bus registered, assigned bus
number 1
[ 3.210235] ehci-omap ehci-omap.0: irq 77, io mem 0x48064800
[ 3.227294] ehci-omap ehci-omap.0: USB 2.0 started, EHCI 1.00
[ 3.233428] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 3.240661] usb usb1: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 3.248352] usb usb1: Product: OMAP-EHCI Host Controller
[ 3.254028] usb usb1: Manufacturer: Linux 3.2.18 ehci_hcd
[ 3.259826] usb usb1: SerialNumber: ehci-omap.0
[ 3.265350] hub 1-0:1.0: USB hub found
[ 3.269409] hub 1-0:1.0: 3 ports detected
[ 3.305328] Initializing USB Mass Storage driver...
[ 3.310577] usbcore: registered new interface driver usb-storage
[ 3.317016] USB Mass Storage support registered.
[ 3.322052] usbcore: registered new interface driver libusual
[ 3.328277] udc: OMAP UDC driver, version: 4 October 2004 (iso) (dma)
[ 3.335601] mousedev: PS/2 mouse device common for all mice
[ 3.343719] input: twl4030_pwrbutton as
/devices/platform/omap/omap_i2c.1/i2c-1/1-0049/twl4030_pwrbutton/input/input0
[ 3.355590] i2c /dev entries driver
[ 3.359954] Linux media interface: v0.10
[ 3.364227] lirc_dev: IR Remote Control driver registered, major 249
[ 3.371124] Driver for 1-wire Dallas network protocol.
[ 3.377319] OMAP Watchdog Timer Rev 0x31: initial timeout 60 sec
[ 3.384399] twl4030_wdt twl4030_wdt: Failed to register misc device
[ 3.391113] twl4030_wdt: probe of twl4030_wdt failed with error -16
[ 3.398773] device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised:
dm-de...@redhat.com
[ 3.408264] cpuidle: using governor ladder
[ 3.412536] cpuidle: using governor menu
[ 3.416778] sdhci: Secure Digital Host Controller Interface driver
[ 3.423339] sdhci: Copyright(c) Pierre Ossman
[ 3.602416] usb 1-2: new high-speed USB device number 2 using ehci-omap
[ 3.652099] gpio_request: gpio-0 (mmc_wp) status -16
[ 3.652130] omap_hsmmc: probe of omap_hsmmc.1 failed with error -16
[ 3.658966] Registered led device: beagleboard::usr0
[ 3.659057] Registered led device: beagleboard::usr1
[ 3.660125] Registered led device: beagleboard::pmu_stat
[ 3.660491] usbcore: registered new interface driver usbhid
[ 3.666473] usbhid: USB HID core driver
[ 3.670471] oprofile: hardware counters not available
[ 3.675903] oprofile: using timer interrupt.
[ 3.681182] TCP cubic registered
[ 3.685363] NET: Registered protocol family 10
[ 3.691711] NET: Registered protocol family 17
[ 3.696594] Registering the dns_resolver key type
[ 3.701568] VFP support v0.3: implementor 41 architecture 3 part 30
variant c rev 3
[ 3.709716] ThumbEE CPU extension supported.
[ 3.714263] Registering SWP/SWPB emulation handler
[ 3.723144] sr_init: No PMIC hook to init smartreflex
[ 3.728729] smartreflex smartreflex.0: omap_sr_probe: SmartReflex driver
initialized
[ 3.737030] smartreflex smartreflex.1: omap_sr_probe: SmartReflex driver
initialized
[ 3.745269] SmartReflex Class3 initialized
[ 3.753051] clock: disabling unused clocks to save power
[ 3.759582] registered taskstats version 1
[ 3.814605] usb 1-2: New USB device found, idVendor=0424, idProduct=9514
[ 3.821746] usb 1-2: New USB device strings: Mfr=0, Product=0,
SerialNumber=0
[ 3.830352] hub 1-2:1.0: USB hub found
[ 3.849822] Console: switching to colour frame buffer device 160x45
[ 3.871246] hub 1-2:1.0: 5 ports detected
[ 3.878967] regulator_init_complete: VDAC: incomplete constraints,
leaving on
[ 3.886779] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[ 3.894744] Waiting for root device /dev/mmcblk0p2...
[ 4.180755] usb 1-2.1: new high-speed USB device number 3 using ehci-omap
[ 4.291076] mmc0: host does not support reading read-only switch.
assuming write-enable.
[ 4.302520] mmc0: new high speed SDHC card at address 0007
[ 4.309020] mmcblk0: mmc0:0007 SD8GB 7.42 GiB
[ 4.315002] usb 1-2.1: New USB device found, idVendor=0424,
idProduct=ec00
[ 4.322509] usb 1-2.1: New USB device strings: Mfr=0, Product=0,
SerialNumber=0
[ 4.330749] mmcblk0: p1 p2
[ 4.422943] usb 1-2.2: new low-speed USB device number 4 using ehci-omap
[ 4.464691] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data
mode. Opts: (null)
[ 4.478454] VFS: Mounted root (ext4 filesystem) readonly on device 179:2.
[ 4.493011] devtmpfs: mounted
[ 4.501678] Freeing init memory: 280K
[ 4.556793] usb 1-2.2: New USB device found, idVendor=0a81,
idProduct=0101
[ 4.569183] usb 1-2.2: New USB device strings: Mfr=1, Product=2,
SerialNumber=0
[ 4.581970] usb 1-2.2: Product: USB Keyboard
[ 4.591491] usb 1-2.2: Manufacturer: CHESEN
[ 4.607635] input: CHESEN USB Keyboard as
/devices/platform/usbhs-omap.0/ehci-omap.0/usb1/1-2/1-2.2/1-2.2:1.0/input/input1
[ 4.625244] generic-usb 0003:0A81:0101.0001: input,hidraw0: USB HID
v1.10 Keyboard [CHESEN USB Keyboard] on usb-ehci-omap.0-2.2/input0
[ 4.651824] input: CHESEN USB Keyboard as
/devices/platform/usbhs-omap.0/ehci-omap.0/usb1/1-2/1-2.2/1-2.2:1.1/input/input2
[ 4.670257] generic-usb 0003:0A81:0101.0002: input,hidraw1: USB HID
v1.10 Device [CHESEN USB Keyboard] on usb-ehci-omap.0-2.2/input1
[ 4.774414] usb 1-2.3: new low-speed USB device number 5 using ehci-omap
[ 4.904663] usb 1-2.3: New USB device found, idVendor=093a,
idProduct=2510
[ 4.917907] usb 1-2.3: New USB device strings: Mfr=1, Product=2,
SerialNumber=0
[ 4.931488] usb 1-2.3: Product: USB OPTICAL MOUSE
[ 4.942291] usb 1-2.3: Manufacturer: PIXART
[ 4.959655] input: PIXART USB OPTICAL MOUSE as
/devices/platform/usbhs-omap.0/ehci-omap.0/usb1/1-2/1-2.3/1-2.3:1.0/input/input3
[ 4.978698] generic-usb 0003:093A:2510.0003: input,hidraw2: USB HID
v1.11 Mouse [PIXART USB OPTICAL MOUSE] on usb-ehci-omap.0-2.3/input0
[ 5.545318] Bluetooth: Core ver 2.16
[ 5.555419] NET: Registered protocol family 31
[ 5.566162] Bluetooth: HCI device and connection manager initialized
[ 5.578979] Bluetooth: HCI socket layer initialized
[ 5.590179] Bluetooth: L2CAP socket layer initialized
[ 5.601531] Bluetooth: SCO socket layer initialized
[ 5.634460] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 5.672058] udevd[60]: starting version 182
[ 5.728424] Bluetooth: RFCOMM TTY layer initialized
[ 5.739746] Bluetooth: RFCOMM socket layer initialized
[ 5.751220] Bluetooth: RFCOMM ver 1.11
[ 6.563659] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null)
[ 7.430877] twl_rtc twl_rtc: rtc core: registered twl_rtc as rtc0
[ 7.655578] smsc95xx v1.0.4
[ 7.906890] smsc95xx 1-2.1:1.0: eth0: register 'smsc95xx' at
usb-ehci-omap.0-2.1, smsc95xx USB 2.0 Ethernet, 52:34:5c:35:a4:24
[ 7.925170] usbcore: registered new interface driver smsc95xx
[ 20.469390] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 21.978546] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 21.987274] smsc95xx 1-2.1:1.0: eth0: link up, 100Mbps, full-duplex, lpa
0x45E1
[ 65.169067] usb 1-2.3: USB disconnect, device number 5
