Hi All,
Please disregard password. I must be getting sleepy.
Disconbobilated,
Eric
>
>
>
>Hi Harry,
> Below is the arachne.cfg that I use to connect
>to a BBS/PPP type ISP. After it dials and connects, it then
>asks you to press F7 to load packet driver. If I wait too long
>before I press F7, then I have to enter my name & password
>manually.
>
> Eric
>
>Harry Murphy wrote:
>>
>>Arachne Wizards:
>>
>> I'm still having trouble linking to my ISP and would
>>appreciate any help you can give me. As I said in an earlier
>>message, when I dial my ISP, I find myself in text mode, as if I
>>were trying to access my ISP's BBS system, rather than his Web
>>site.
>>---<snip>---<
>> I'm attaching my ARACHNE.CFG file (with my password changed)
>>to this message. Any suggestions would be very greatly
>>appreciated. I really want to get Arachne up and running before
>>my ISP yanks his BBS service.
>>
>>Best Wishes from
>>Sunny (and Cold!) New Mexico,
>>
>>Harry M. Murphy
>>
>**************************************
>File 1: uses F7 to log on:
>
>;This is ARACHNE.CFG for Arachne version 1.6+
>;If you want to use Arachne on PC with CPU 486+ you should start here.
>;(tested on AMD K5/133). This profile is slightly less video-intensive.
>;This configuration file can be completely controled from Arachne setup.
>;Run "setup" if you are not sure what to change in configuration file.
>
>[profile]
>Profile 486PC.ACF
>Connection @epppd.exe>>PPP.LOG
>Hangup @termin.com 0x60>NUL
>
>;Connection @cmd ... command cmd will estabilish connection
>;Connection READY ... connection is permanent, packet driver in AUTOEXEC...
>;Connection NUL ... do not start TCP/IP (run "arachne -c" to force this)
>
>[dialer]
>DialPage file:home.bmp
>Dialer @MINITERM.EXE>PPP.LOG
>TerminalWindow @MINITERM.EXE
>UseTerminal Yes
>Port 1 < insert proper data for your system
>Irq 4 < insert proper data for your system
>Base 0x3f8 < insert proper data for your system
>Mode 8N1
>Speed 38400
>InitString +++AT&F < insert proper data for your system
>DialString ATDT
>PhoneNumber 1-248-553-7653 < insert proper data for your system
>Autologin No
>WaitFor1 name:
>Response1 \u
>WaitFor2 sword:
>Response2 \p
>;WaitFor3 < note ";" to comment out this line
>;Response3 < note ";" to comment out this line
>PPPusername xxxxxxxx
>PPPpassword xxxxxxxx
>
>;Port values: 0=non-standard serial (COM) port, 1-4 standard ports
>;Base values: 0x??? (eg. 0x3e8) - Base and Irq are used for "Port 0"
>;Mode values: databits/parity/stopbits (eg. 8N1)
>
>[tcp/ip]
>IP_Address PPP
>IP_Grab IP address set to
>NameServer 209.104.141.196 < insert proper data for your system
>AltNameServer 209.104.131.25 < insert proper data for your system
>Gateway 0.0.0.0
>AltGateway 0.0.0.0
>Netmask 0.0.0.0
>TCPconfig PPPTCP.CFG
>
>***********************************************
>
>
>--
> __________
> | Ayrx |__\_ Eric S. Emerson
> | E-male:~_: ! [EMAIL PROTECTED]
> `~(*)~~~~(*)~' `````````````````````````
>
>
--
__________
| Ayrx |__\_ Eric S. Emerson
| E-male:~_: ! [EMAIL PROTECTED]
`~(*)~~~~(*)~' `````````````````````````
