Hi, I have a RPi 3B running Leap 15.5. I have recently replaced the failing SD card about three weeks ago and all was well.
After a zypper patch + reboot cycle it failed to connect to the network. Connecting via a serial cable shows that it hangs at 'Reached basic system'. The early boot messages don't tell me that much, there seem to be some errors, pasted at the end of the message. I mounted the SD card in another machine, looks to mount just fine NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINTS sda 8:0 1 59.4G 0 disk ├─sda1 8:1 1 64M 0 part /run/media/robert/EFI ├─sda2 8:2 1 500M 0 part └─sda3 8:3 1 6.8G 0 part /run/media/robert/ROOT dmesg complains about 'not properly unmounted', but that should not be a big issue [229713.544212] scsi 0:0:0:0: Direct-Access Generic STORAGE DEVICE 1402 PQ: 0 ANSI: 6 [229713.544584] sd 0:0:0:0: Attached scsi generic sg0 type 0 [229713.788123] sd 0:0:0:0: [sda] 124669952 512-byte logical blocks: (63.8 GB/59.4 GiB) [229713.789352] sd 0:0:0:0: [sda] Write Protect is off [229713.789357] sd 0:0:0:0: [sda] Mode Sense: 21 00 00 00 [229713.790605] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [229713.800319] sda: sda1 sda2 sda3 [229713.800711] sd 0:0:0:0: [sda] Attached SCSI removable disk [229714.844629] FAT-fs (sda1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck. [229715.016300] EXT4-fs (sda3): mounted filesystem f9dbd32e-e10c-4b7c- b75e-1e0dfabdca45 r/w with ordered data mode. Quota mode: none. I ran fsck, the only thing that it did was clear the dirty bit $ sudo fsck /dev/sda1 fsck from util-linux 2.39.3 fsck.fat 4.2 (2021-01-31) Dirty bit is set. Fs was not properly unmounted and some data may be corrupt. 1) Remove dirty bit 2) No action [12?q]? 1 *** Filesystem was changed *** The changes have not yet been written, you can still choose to leave the filesystem unmodified: 1) Write changes 2) Leave filesystem unchanged [12?q]? 1 /dev/sda1: 292 files, 4395/32695 clusters How can I further check for problems? Thanks, Robert Full early boot message below: U-Boot 2021.10 (Aug 04 2022 - 12:00:00 +0000) DRAM: 992 MiB RPI 3 Model B (0xa02082) MMC: mmc@7e202000: 0, mmcnr@7e300000: 1 Loading Environment from FAT... Unable to read "uboot.env" from mmc0:1... In: serial Out: vidconsole Err: vidconsole Net: No ethernet found. starting USB... Bus usb@7e980000: USB DWC2 scanning bus usb@7e980000 for devices... 3 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found Hit any key to stop autoboot: 0 switch to partitions #0, OK mmc0 is current device Scanning mmc 0:3... libfdt fdt_check_header(): FDT_ERR_BADMAGIC Scanning disk m...@7e202000.blk... No valid Btrfs found Card did not respond to voltage select! : -110 Scanning disk mm...@7e300000.blk... Disk mm...@7e300000.blk not ready Found 4 disks Missing RNG device for EFI_RNG_PROTOCOL No EFI system partition BootOrder not defined EFI boot manager: Cannot load any image ** Invalid partition 4 ** Couldn't find partition mmc 0:4 No valid Btrfs found Scanning mmc 0:1... libfdt fdt_check_header(): FDT_ERR_BADMAGIC BootOrder not defined EFI boot manager: Cannot load any image Found EFI removable media binary efi/boot/bootaa64.efi 1509376 bytes read in 67 ms (21.5 MiB/s) libfdt fdt_check_header(): FDT_ERR_BADMAGIC Booting /efi\boot\bootaa64.ef