Hi I have a Pi5 4GB with a Radxa Dual 2.5G Router HAT. In the config.ini I added following 2 lines:
dtparam=pciex1 dtparam=pciex1_gen=2 OpenBSD 7.9 installation worked according the manual, booting from the sdcard. But I have following 2 issues (when booting raspberry pi OS, HAT works as expected) 1) For the network interfaces, I only see 2 (instead of 3): cad0 and rge0 - any ideas?2) When adding a SSD Crucial P310 1gb, the system crashes at startup (see below) Let me know if I can provide more data Thanks Sean Cannot persist EFI variables without system partition ** Booting bootflow '<NULL>' with efi_mgr Booting: Label: mmc 0 Device path: /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b,0000000000000000)/VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b,6d00000001000000)/SD(0)/SD(0) disks: sd0* >> OpenBSD/arm64 BOOTAA64 1.24 boot> cannot open sd0a:/etc/random.seed: No such file or directory booting sd0a:/bsd: 3201768+1344104+12714976+652288 [294291+91+757440+311692]=0x140c928 Copyright (c) 1982, 1986, 1989, 1991, 1993 The Regents of the University of California. All rights reserved. Copyright (c) 1995-2026 OpenBSD. All rights reserved. https://www.OpenBSD.org OpenBSD 7.9 (RAMDISK) #211: Wed May 6 18:34:33 MDT 2026 [email protected]:/usr/src/sys/arch/arm64/compile/RAMDISK real mem = 4284379136 (4085MB) avail mem = 4066193408 (3877MB) random: good seed from bootblocks mainbus0 at root: Raspberry Pi 5 Model B Rev 1.1 psci0 at mainbus0: PSCI 1.1, SMCCC 1.2, SYSTEM_SUSPEND efi0 at mainbus0: UEFI 2.11 efi0: Das U-Boot rev 0x20250700 smbios0 at efi0: SMBIOS 3.7.0 smbios0: vendor U-Boot version "2025.07" date 07/01/2025 smbios0: raspberrypi Raspberry Pi 5 Model B Rev 1.1 cpu0 at mainbus0 mpidr 0: ARM Cortex-A76 r4p1 cpu0: 64KB 64b/line 4-way L1 PIPT I-cache, 64KB 64b/line 4-way L1 D-cache cpu0: 512KB 64b/line 8-way L2 cache cpu0: 2048KB 64b/line 16-way L3 cache cpu0: DP,RDM,Atomic,CRC32,SHA2,SHA1,AES+PMULL,LRCPC,DPB,ASID16,PAN+ATS1E1,LO,HPDS,VH,HAFDBS,CSV3,CSV2,RAS,AdvSIMD+HP,FP+HP,SSBS "atf" at mainbus0 not configured "linux,cma" at mainbus0 not configured "nvram" at mainbus0 not configured simplefb0 at mainbus0: 1920x1080, 16bpp wsdisplay0 at simplefb0 mux 1 wsdisplay0: screen 0 added (std, vt100 emulation) "system" at mainbus0 not configured simplebus0 at mainbus0: "clocks" "clk-osc" at simplebus0 not configured "clk-vpu" at simplebus0 not configured "clk-uart" at simplebus0 not configured "clk-emmc2" at simplebus0 not configured "clk-usb" at simplebus0 not configured "clk_xosc" at simplebus0 not configured "sdio_src" at simplebus0 not configured "sdhci_core" at simplebus0 not configured simplebus1 at mainbus0: "soc" bcmstbrescal0 at simplebus1 bcmstbreset0 at simplebus1 bcmmbox0 at simplebus1 bcmstbgpio0 at simplebus1 ampintc0 at simplebus1 nirq 320, ncpu 4: "interrupt-controller" bcmstbpinctrl0 at simplebus1 bcmstbgpio1 at simplebus1 bcmstbpinctrl1 at simplebus1 syscon0 at simplebus1: "avs-monitor" "thermal" at syscon0 not configured sdhc0 at simplebus1 sdhc0: SDHC 3.00, 200 MHz base clock sdmmc0 at sdhc0: 4-bit, sd high-speed, mmc high-speed, ddr52, dma "timer" at simplebus1 not configured "interrupt-controller" at simplebus1 not configured pluart0 at simplebus1: rev 3, 32 byte fifo pluart0: console "clock" at simplebus1 not configured "intc" at simplebus1 not configured "intc" at simplebus1 not configured "spi" at simplebus1 not configured "watchdog" at simplebus1 not configured bcmirng0 at simplebus1 "intc" at simplebus1 not configured "serial" at simplebus1 not configured "firmware" at simplebus1 not configured "power" at simplebus1 not configured "fb" at simplebus1 not configured rpirtc0 at simplebus1 simplebus2 at simplebus1: "nvmem" "nvmem_otp" at simplebus2 not configured "nvmem_cust" at simplebus2 not configured "nvmem_mac" at simplebus2 not configured "nvmem_priv" at simplebus2 not configured "fixedregulator_3v3" at simplebus1 not configured "fixedregulator_5v0" at simplebus1 not configured "gpiomem" at simplebus1 not configured "gpiomem" at simplebus1 not configured "gpiomem" at simplebus1 not configured "gpiomem" at simplebus1 not configured simplebus3 at mainbus0: "axi" bcmmip0 at simplebus3 bcmmip1 at simplebus3 syscon1 at simplebus3: "syscon" bcmpcie0 at simplebus3 pci0 at bcmpcie0 ppb0 at pci0 dev 0 function 0 "Broadcom BCM2712" rev 0x30 pci1 at ppb0 bus 1 ppb1 at pci1 dev 0 function 0 vendor "ASMedia", unknown product 0x2806 rev 0x01 pci2 at ppb1 bus 2 ppb2 at pci2 dev 0 function 0 vendor "ASMedia", unknown product 0x2806 rev 0x01: msi pci3 at ppb2 bus 3 ppb3 at pci2 dev 2 function 0 vendor "ASMedia", unknown product 0x2806 rev 0x01: msi pci4 at ppb3 bus 7 ppb4 at pci2 dev 6 function 0 vendor "ASMedia", unknown product 0x2806 rev 0x01: msi pci5 at ppb4 bus 9 rge0 at pci5 dev 0 function 0 "Realtek RTL8125" rev 0x05: msix: RTL8125B, address 00:48:54:20:39:66 ppb5 at pci2 dev 14 function 0 vendor "ASMedia", unknown product 0x2806 rev 0x01: not configured by system firmware bcmpcie1 at simplebus3 pci6 at bcmpcie1 ppb6 at pci6 dev 0 function 0 "Broadcom BCM2712" rev 0x30 pci7 at ppb6 bus 1 rpone0 at pci7 dev 0 function 0 "Raspberry Pi RP1" rev 0x00 simplebus4 at rpone0: "rp1" rpiclock0 at simplebus4 rpigpio0 at simplebus4 "mailbox" at simplebus4 not configured rpipwm0 at simplebus4 "adc" at simplebus4 not configured cad0 at simplebus4: rev 0x70109, address 88:a2:9e:c0:18:27 brgphy0 at cad0 phy 1: BCM54210E, rev. 2 "pio" at simplebus4 not configured "dma" at simplebus4 not configured xhci0 at simplebus4, xHCI 1.10 usb0 at xhci0: USB revision 3.0 uhub0 at usb0 configuration 1 interface 0 "Generic xHCI root hub" rev 3.00/1.00 addr 1 xhci1 at simplebus4, xHCI 1.10 usb1 at xhci1: USB revision 3.0 uhub1 at usb1 configuration 1 interface 0 "Generic xHCI root hub" rev 3.00/1.00 addr 1 "sram" at simplebus4 not configured "gpiomem" at simplebus4 not configured "iommu" at simplebus3 not configured "iommu" at simplebus3 not configured "iommu" at simplebus3 not configured "iommuc" at simplebus3 not configured "dma" at simplebus3 not configured "dma" at simplebus3 not configured "codec" at simplebus3 not configured "pisp_be" at simplebus3 not configured sdhc1 at simplebus3 sdhc1: SDHC 3.00, 200 MHz base clock sdmmc1 at sdhc1: 4-bit, sd high-speed, mmc high-speed, ddr52, dma agtimer0 at mainbus0: 54000 kHz "clk-27M" at mainbus0 not configured "clk-108M" at mainbus0 not configured "arm-pmu" at mainbus0 not configured "phy" at mainbus0 not configured "leds" at mainbus0 not configured "sd-io-1v8-reg" at mainbus0 not configured "sd-vcc-reg" at mainbus0 not configured "wl-on-reg" at mainbus0 not configured "cam0_reg" at mainbus0 not configured "cam1_reg" at mainbus0 not configured "cam_dummy_reg" at mainbus0 not configured "dummy" at mainbus0 not configured "i2c0if" at mainbus0 not configured "i2c0mux" at mainbus0 not configured "rp1_firmware" at mainbus0 not configured "rp1_vdd_3v3" at mainbus0 not configured pwmfan0 at mainbus0 "pwr_button" at mainbus0 not configured sdmmc1: can't supply bus power sdmmc1: can't enable card scsibus0 at sdmmc0: 2 targets, initiator 0 sd0 at scsibus0 targ 1 lun 0: <Sandisk, SL32G, 0030> removable sd0: 29664MB, 512 bytes/sector, 60751872 sectors uhidev0 at uhub0 port 2 configuration 1 interface 0 "Logitech Gaming Mouse G402" rev 2.00/90.03 addr 2 uhidev0: iclass 3/1 uhid at uhidev0 not configured uhidev1 at uhub0 port 2 configuration 1 interface 1 "Logitech Gaming Mouse G402" rev 2.00/90.03 addr 2 uhidev1: iclass 3/0, 17 report ids ukbd0 at uhidev1 reportid 1 wskbd0 at ukbd0 mux 1 wskbd0: connecting to wsdisplay0 uhid at uhidev1 reportid 3 not configured uhid at uhidev1 reportid 4 not configured uhid at uhidev1 reportid 16 not configured uhid at uhidev1 reportid 17 not configured uhidev2 at uhub1 port 2 configuration 1 interface 0 "Logitech G515 TKL" rev 2.00/67.00 addr 2 uhidev2: iclass 3/1 ukbd1 at uhidev2 wskbd1 at ukbd1 mux 1 wskbd1: connecting to wsdisplay0 uhidev3 at uhub1 port 2 configuration 1 interface 1 "Logitech G515 TKL" rev 2.00/67.00 addr 2 uhidev3: iclass 3/1, 4 report ids uhid at uhidev3 reportid 2 not configured uhid at uhidev3 reportid 3 not configured uhid at uhidev3 reportid 4 not configured uhidev4 at uhub1 port 2 configuration 1 interface 2 "Logitech G515 TKL" rev 2.00/67.00 addr 2 uhidev4: iclass 3/0, 17 report ids uhid at uhidev4 reportid 16 not configured uhid at uhidev4 reportid 17 not configured softraid0 at root scsibus1 at softraid0: 256 targets root on rd0a swap on rd0b dump on rd0b WARNING: bad clock chip time WARNING: CHECK AND RESET THE DATE! SError: 28db20 esr be000011 far ffffff805e85e000 panic: do_el0_error syncing disks... done
