On 10/21/05 01:14 Konstantin Prokazoff said the following:
We haven't touched drivers yet, but I think card you have using aren't
buggy. Can you try to set in zaptel.conf different sync sources for
different spans? For example, first span, sync source 1, fourth span - sync
i have, first setting all spans to use timing=0, then using your suggestion
above. neither worked. see my other email on this to asterisk-users.
source 2 and so on. Don't use CRC if this options not required by other
side, cause due to standards, CRC4 not recommended for E1s. As addition, can
removed CRC4.
And very interesting for me, what type of chipset are you using. I have 4
severs on Intel 72 and 73 chipset, but zttest shows no more than 99,98%.
zttest
--- Results after 21 passes ---
Best: 100.000000 -- Worst: 99.987793 -- Average: 99.998256
on other runs, i've got averages of 99.9998 as well.
dmesg follows:
Copyright (c) 1992-2005 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 4.11-STABLE #0: Wed Oct 19 19:49:04 MYT 2005
[EMAIL PROTECTED]:/usr/src/sys/compile/ALPHAQUE
Timecounter "i8254" frequency 1193182 Hz
Timecounter "TSC" frequency 2791123856 Hz
CPU: Intel(R) Xeon(TM) CPU 2.80GHz (2791.12-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0xf25 Stepping = 5
Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,C
MOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
Hyperthreading: 2 logical CPUs
real memory = 1073676288 (1048512K bytes)
avail memory = 1014792192 (991008K bytes)
Preloaded elf kernel "kernel" at 0xc1d12000.
Preloaded mfs_root "/mfsroot" at 0xc1d1209c.
Warning: Pentium 4 CPU: PSE disabled
Pentium Pro MTRR support enabled
md0: Preloaded image </mfsroot> 25165824 bytes at 0xc0510aac
md1: Malloc disk
Using $PIR table, 10 entries at 0xc00fdf20
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <ServerWorks host to PCI bridge(unknown chipset)> on motherboard
pci0: <PCI bus> on pcib0
pci0: <ATI Mach64-GR graphics accelerator> at 5.0 irq 10
atapci0: <ITE 8211F/8212F PCI Controller> port
0x1400-0x140f,0x1420-0x1423,0x142
8-0x142f,0x1424-0x1427,0x1430-0x1437 irq 5 at device 6.0 on pci0
ata2: at 0x1430 on atapci0
ata3: at 0x1428 on atapci0
isab0: <PCI to ISA bridge (vendor=1166 device=0203)> at device 15.0 on pci0
isa0: <ISA bus> on isab0
atapci1: <ServerWorks CSB6 ATA100 controller (channel 0+1)> port
0x1410-0x141f,0
x374-0x377,0x170-0x177,0x3f4-0x3f7,0x1f0-0x1f7 at device 15.1 on pci0
ata0: at 0x1f0 irq 14 on atapci1
ata1: at 0x170 irq 15 on atapci1
ohci0: <OHCI (generic) USB controller> mem 0xcc000-0xccfff irq 9 at device
15.2
usb0: OHCI version 1.0, legacy support
usb0: SMM does not respond, resetting
usb0: <OHCI (generic) USB controller> on ohci0
usb0: USB revision 1.0
uhub0: 4 ports with 4 removable, self powered
pcib1: <ServerWorks host to PCI bridge(unknown chipset)> on motherboard
pci1: <PCI bus> on pcib1
pci1: <unknown card> (vendor=0x10ee, dev=0x0314) at 5.0 irq 7
pcib2: <Host to PCI bridge> on motherboard
pci2: <PCI bus> on pcib2
bge0: <Broadcom BCM5704C Dual Gigabit Ethernet, ASIC rev. 0x2002> mem
0xfc700000
-0xfc70ffff,0xfc710000-0xfc71ffff irq 11 at device 0.0 on pci2
bge0: Ethernet address: 00:0d:61:15:6d:da
miibus0: <MII bus> on bge0
brgphy0: <BCM5704 10/100/1000baseTX PHY> on miibus0
brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX,
1000baseTX
-FDX, auto
bge1: <Broadcom BCM5704C Dual Gigabit Ethernet, ASIC rev. 0x2002> mem
0xfc720000
-0xfc72ffff,0xfc730000-0xfc73ffff irq 10 at device 0.1 on pci2
bge1: Ethernet address: 00:0d:61:15:6d:db
miibus1: <MII bus> on bge1
brgphy1: <BCM5704 10/100/1000baseTX PHY> on miibus1
brgphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX,
1000baseTX
-FDX, auto
pcib3: <Host to PCI bridge> on motherboard
pci3: <PCI bus> on pcib3
pcib4: <Host to PCI bridge> on motherboard
pci4: <PCI bus> on pcib4
orm0: <Option ROMs> at iomem
0xc0000-0xc7fff,0xc8000-0xcbfff,0xdf000-0xdffff on
isa0
pmtimer0 on isa0
fdc0: ready for input in output
fdc0: cmd 3 failed at out byte 1 of 3
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x100>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A, console
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
BRIDGE 020214 loaded
IPsec: Initialized Security Association Processing.
IP Filter: v3.4.35 initialized. Default = block all, Logging = enabled
ad4: 76319MB <ST380011A> [155061/16/63] at ata2-master UDMA100
acd0: CDROM <QSI CD-ROM SCR-242> at ata0-master PIO4
Mounting root from ufs:/dev/md0c
--
Regards, /\_/\ "All dogs go to heaven."
[EMAIL PROTECTED] (0 0) http://www.alphaque.com/
+==========================----oOO--(_)--OOo----==========================+
| for a in past present future; do |
| for b in clients employers associates relatives neighbours pets; do |
| echo "The opinions here in no way reflect the opinions of my $a $b." |
| done; done |
+=========================================================================+
_______________________________________________
Asterisk-BSD mailing list
[email protected]
http://lists.digium.com/mailman/listinfo/asterisk-bsd
