hello, according to http://www.freshports.org/net/asterisk/
hfc-support was removed in asterisk 1.2.7.1 . in previous versions it was sometimes (?) included, however it worked quite poor because of the zaphfc-driver, at least i would guess so. maybe you can run asterisk in linux emulation, in former 4.x -times it worked quite well. bye joerg > ----- Original Message ----- > From: Georg <[EMAIL PROTECTED]> > To: [email protected] > Subject: [Asterisk-bsd] bristuffed asterisk for hfc-s chips > Date: Tue, 06 Jun 2006 10:32:58 +0200 > > > Hi everyone, > > I'm trying to set up a system (with FreeBSD 6.0 and 6.1) with > asterisk (bristuffed) and a HFC based ISDN card. > The same hardware works under Linux - but I wanted to do it with FreeBSD. > > So I installed the port /usr/ports/net/asterisk-bristuff. > The installation went without any problems. > > Just one basic question: Is this port designed to work with HFC > based cards/chips?? > > My /usr/local/etc/zaptel.conf looks like this: > ------------ > loadzone=nl > defaultzone=nl > span=1,1,3,ccs,ami > bchan=1-2 > dchan=3 > ------------ > > In my zapata.conf in /usr/local/etc/asterisk/zapata.conf I use the > following settings (which work fine under Linux): > ------------------ > switchtype=euroisdn > signalling=bri_net_ptmp > ------------------ > > > When I startup asterisk I always get the following error: > ---- > == Parsing '/usr/local/etc/asterisk/zapata.conf': Found > Jun 6 07:56:46 ERROR[26954]: chan_zap.c:10648 setup_zap: Unknown > signalling method 'bri_net_ptmp' > Jun 6 07:56:46 ERROR[26954]: chan_zap.c:10273 setup_zap: > Signalling must be specified before any channels are. > Jun 6 07:56:46 WARNING[26954]: loader.c:414 __load_resource: > chan_zap.so: load_module failed, returning -1 > Jun 6 07:56:46 WARNING[26954]: loader.c:554 load_modules: Loading > module chan_zap.so failed! > > ---- > > So I startet looking in the source and at the libraries. The first > thing is: Why are there different sized chan_zap.so and why is the > smaller one (which differs from bristuff-port) from the > non-bristuff installed?: > ---------------- > [server] /usr/ports/net/asterisk-bristuff# ls -la > /usr/ports/net/asterisk-bristuff/work/asterisk-1.2.7.1/channels/chan_zap.so > -rwxr-xr-x 1 root wheel 265654 Jun 6 07:30 > /usr/ports/net/asterisk-bristuff/work/asterisk-1.2.7.1/channels/chan_zap.so > > [server] /usr/ports/net/asterisk-bristuff# ls -la > /usr/local/lib/asterisk/modules/chan_zap.so* > -r-xr-xr-x 1 root wheel 257680 Jun 6 07:32 > /usr/local/lib/asterisk/modules/chan_zap.so > ---------------- > > > Lokking at chan_zap.c I could not find any line saying something > about "bri_*"-signalling like in the patched sources on my > linux-box: > Here is the code on my 6.0 FreeBSD box: > ------------ > #ifdef ZAPATA_PRI > } else if (!strcasecmp(v->value, "pri_net")) > { > cur_radio = 0; > cur_signalling = SIG_PRI; > pritype = PRI_NETWORK; > } else if (!strcasecmp(v->value, "pri_cpe")) > { > cur_signalling = SIG_PRI; > cur_radio = 0; > pritype = PRI_CPE; > } else if (!strcasecmp(v->value, > "gr303fxoks_net")) { > cur_signalling = SIG_GR303FXOKS; > cur_radio = 0; > pritype = PRI_NETWORK; > } else if (!strcasecmp(v->value, > "gr303fxsks_cpe")) { > cur_signalling = SIG_GR303FXSKS; > cur_radio = 0; > pritype = PRI_CPE; > #endif > #ifdef ZAPATA_R2 > ------------ > > ...and here on my Linux-Box: > ---------------- > #ifdef ZAPATA_PRI > } else if (!strcasecmp(v->value, "pri_net")) > { > cur_radio = 0; > cur_signalling = SIG_PRI; > pritype = PRI_NETWORK; > } else if (!strcasecmp(v->value, "pri_cpe")) > { > cur_signalling = SIG_PRI; > cur_radio = 0; > pritype = PRI_CPE; > } else if (!strcasecmp(v->value, > "gr303fxoks_net")) { > cur_signalling = SIG_GR303FXOKS; > cur_radio = 0; > pritype = PRI_NETWORK; > } else if (!strcasecmp(v->value, > "gr303fxsks_cpe")) { > cur_signalling = SIG_GR303FXSKS; > cur_radio = 0; > pritype = PRI_CPE; > } else if (!strcasecmp(v->value, "bri_net_ptmp")) { > cur_radio = 0; > cur_signalling = SIG_PRI; > pritype = BRI_NETWORK_PTMP; > } else if (!strcasecmp(v->value, "bri_cpe_ptmp")) { > cur_signalling = SIG_PRI; > cur_radio = 0; > pritype = BRI_CPE_PTMP; > } else if (!strcasecmp(v->value, "bri_net")) { > cur_radio = 0; > cur_signalling = SIG_PRI; > pritype = BRI_NETWORK; > } else if (!strcasecmp(v->value, "bri_cpe")) { > cur_signalling = SIG_PRI; > cur_radio = 0; > pritype = BRI_CPE; > #endif > #ifdef ZAPATA_R2 > ---------------- > > It seems that all the code for the signalling with HFC-based cards > is missing or am I doing something comletely wrong? What do I have > to do to enable all the "bri_*"-type signalling? > > > Thanks for any reply! > > Regards, > > Georg > _______________________________________________ > Asterisk-BSD mailing list > [email protected] > http://lists.digium.com/mailman/listinfo/asterisk-bsd > -- ___________________________________________ Graffiti.net free e-mail @ www.graffiti.net Play 100s of games for FREE! http://games.graffiti.net/ Powered By Outblaze _______________________________________________ Asterisk-BSD mailing list [email protected] http://lists.digium.com/mailman/listinfo/asterisk-bsd
