It detects TDM2400 and TE110p together: Dec 24 13:20:39 iax kernel: Zapata Telephony Interface Registered on major 196 Dec 24 13:20:39 iax kernel: Echo Canceller: MG2 Dec 24 13:20:39 iax kernel: T1/E1 device: vendor=e159 device=1 subvendor=79fe Dec 24 13:20:39 iax kernel: wcte11xp0: <Digium Wildcard TE110P T1/E1 Board> port 0x1000-0x10ff mem 0x52000000-0x52000fff irq 22 at device 1.0 on pci7 Dec 24 13:20:39 iax kernel: WCT1xxP Attach for wcte11xp0: deviceID : 0xe159 Dec 24 13:20:39 iax kernel: wcte11xp0: [FAST] Dec 24 13:20:39 iax kernel: FALC version: 00000005 Dec 24 13:20:39 iax kernel: TE110P: Setting up global serial parameters for E1 FALC V2.2 Dec 24 13:20:39 iax kernel: TE110P: Successfully initialized serial bus for card Dec 24 13:20:39 iax kernel: Found a Wildcard: Digium Wildcard TE110P T1/E1 Dec 24 13:20:39 iax kernel: wctdm: TDM24XXP device: vendor=d161 device=2400 subvendor=d161 Dec 24 13:20:39 iax kernel: wctdm0: <Wildcard TDM2400P> port 0x1400-0x14ff mem 0x52001000-0x520013ff irq 21 at device 0.0 on pci7 Dec 24 13:20:39 iax kernel: wctdm0: [FAST] Dec 24 13:20:39 iax kernel: PCI Config reg is 00000007 Dec 24 13:20:39 iax kernel: Wildcard TDM2400P: New Reg: fe590000! Dec 24 13:20:39 iax kernel: Detected REG0: 00000100 Dec 24 13:20:39 iax kernel: Detected REG1: 00007849 Dec 24 13:20:39 iax kernel: Detected REG2: 0000001d Dec 24 13:20:39 iax kernel: (pre) Reg fc is 50000027 Dec 24 13:20:39 iax kernel: (post) Reg fc is 50000024 Dec 24 13:20:39 iax kernel: Detected REG2: 0000ffff Dec 24 13:20:39 iax kernel: wctdm24xxp: reg is a04c0004 Dec 24 13:20:39 iax kernel: Resetting the modules... Dec 24 13:20:39 iax kernel: During Resetting the modules... Dec 24 13:20:39 iax kernel: After resetting the modules...
but many erros are reported on TDM2400: Dec 24 13:20:39 iax kernel: Port 1: Not installed Dec 24 13:20:39 iax kernel: Excessive leakage detected on module 1: 0 volts (00) after 465 ms Dec 24 13:20:39 iax kernel: ProSLIC module 1 failed leakage test. Check for short circuit Dec 24 13:20:39 iax kernel: !!!!!!! TERM_LP_POLE_Q1Q2 iREG 25 = 0 should be 8C Dec 24 13:20:39 iax kernel: !!!!! Init Indirect Registers UNSUCCESSFULLY. Dec 24 13:20:39 iax kernel: Indirect Registers failed verification. Dec 24 13:20:39 iax kernel: Excessive leakage detected on module 1: 0 volts (00) after 189 ms Dec 24 13:20:39 iax kernel: ProSLIC module 1 failed leakage test. Check for short circuit Dec 24 13:20:39 iax kernel: Proslic Passed Manual Calibration on Second Attempt Dec 24 13:20:39 iax kernel: !!!!!!! RING_TRIP_FILTER iREG 24 = 300 should be 320 Dec 24 13:20:39 iax kernel: !!!!! Init Indirect Registers UNSUCCESSFULLY. Dec 24 13:20:39 iax kernel: Indirect Registers failed verification. Dec 24 13:20:39 iax kernel: Port 2: FAILED FXS (FCC) Dec 24 13:20:39 iax kernel: Excessive leakage detected on module 2: 0 volts (00) after 254 ms Dec 24 13:20:39 iax kernel: ProSLIC module 2 failed leakage test. Check for short circuit Dec 24 13:20:39 iax kernel: !!!!!!! PWR_ALARM_Q1Q2 iREG 20 = C0 should be 7C0 Dec 24 13:20:39 iax kernel: !!!!! Init Indirect Registers UNSUCCESSFULLY. Dec 24 13:20:39 iax kernel: Indirect Registers failed verification. Dec 24 13:20:39 iax kernel: Excessive leakage detected on module 2: 0 volts (00) after 5 ms Dec 24 13:20:39 iax kernel: ProSLIC module 2 failed leakage test. Check for short circuit Dec 24 13:20:39 iax kernel: Proslic Passed Manual Calibration on Second Attempt Dec 24 13:20:39 iax kernel: !!!!!!! RING_TRIP_FILTER iREG 24 = 20 should be 320 Dec 24 13:20:39 iax kernel: !!!!!!! TERM_LP_POLE_Q5Q6 iREG 27 = 0 should be 10 Dec 24 13:20:39 iax kernel: !!!!! Init Indirect Registers UNSUCCESSFULLY. Dec 24 13:20:39 iax kernel: Indirect Registers failed verification. Dec 24 13:20:39 iax kernel: Port 3: FAILED FXS (FCC) Dec 24 13:20:39 iax kernel: Excessive leakage detected on module 3: 0 volts (00) after 93 ms Dec 24 13:20:39 iax kernel: ProSLIC module 3 failed leakage test. Check for short circuit Dec 24 13:20:39 iax kernel: !!!!!!! PWR_ALARM_Q1Q2 iREG 20 = C0 should be 7C0 Dec 24 13:20:39 iax kernel: !!!!! Init Indirect Registers UNSUCCESSFULLY. Dec 24 13:20:39 iax kernel: Indirect Registers failed verification. Dec 24 13:20:39 iax kernel: Proslic Passed Manual Calibration on Second Attempt Dec 24 13:20:39 iax kernel: Port 4: Installed -- MANUAL FXS Dec 24 13:20:39 iax kernel: Excessive leakage detected on module 4: 0 volts (00) after 248 ms Dec 24 13:20:39 iax kernel: ProSLIC module 4 failed leakage test. Check for short circuit Dec 24 13:20:39 iax kernel: Power alarm on module 4, resetting! Dec 24 13:20:39 iax kernel: Power alarm on module 4, resetting! Dec 24 13:20:39 iax kernel: Port 5: Installed -- AUTO FXS/DPO Dec 24 13:20:39 iax kernel: Excessive leakage detected on module 5: 0 volts (00) after 94 ms Dec 24 13:20:39 iax kernel: ProSLIC module 5 failed leakage test. Check for short circuit Dec 24 13:20:39 iax kernel: !!!!!!! OSC2_COEF iREG 10 = 70 should be 7870 Dec 24 13:20:39 iax kernel: !!!!!!! RING_TRIP_FILTER iREG 24 = 300 should be 320 Dec 24 13:20:39 iax kernel: !!!!! Init Indirect Registers UNSUCCESSFULLY. Dec 24 13:20:39 iax kernel: Indirect Registers failed verification. Dec 24 13:20:39 iax kernel: Excessive leakage detected on module 5: 0 volts (00) after 133 ms Dec 24 13:20:39 iax kernel: ProSLIC module 5 failed leakage test. Check for short circuit Dec 24 13:20:39 iax kernel: Proslic Passed Manual Calibration on Second Attempt Dec 24 13:20:39 iax kernel: !!!!!!! RECV_DIGITAL_GAIN iREG 1A = 0 should be 2000 Dec 24 13:20:39 iax kernel: !!!!!!! LOOP_CLOSURE_FILTER iREG 23 = 0 should be 8000 Dec 24 13:20:39 iax kernel: !!!!! Init Indirect Registers UNSUCCESSFULLY. Dec 24 13:20:39 iax kernel: Indirect Registers failed verification. Dec 24 13:20:39 iax kernel: Port 6: FAILED FXS (FCC) Dec 24 13:20:39 iax kernel: Excessive leakage detected on module 6: 0 volts (00) after 49 ms Dec 24 13:20:39 iax kernel: ProSLIC module 6 failed leakage test. Check for short circuit Dec 24 13:20:39 iax kernel: Port 7: Installed -- AUTO FXS/DPO Dec 24 13:20:39 iax kernel: Excessive leakage detected on module 7: 0 volts (00) after 434 ms Dec 24 13:20:39 iax kernel: ProSLIC module 7 failed leakage test. Check for short circuit Dec 24 13:20:39 iax kernel: !!!!!!! LOOP_CLOSURE_FILTER iREG 23 = 0 should be 8000 Dec 24 13:20:39 iax kernel: !!!!! Init Indirect Registers UNSUCCESSFULLY. Dec 24 13:20:39 iax kernel: Indirect Registers failed verification. Dec 24 13:20:39 iax kernel: Excessive leakage detected on module 7: 0 volts (00) after 172 ms Dec 24 13:20:39 iax kernel: ProSLIC module 7 failed leakage test. Check for short circuit Dec 24 13:20:39 iax kernel: Port 8: Installed -- MANUAL FXS Dec 24 13:20:39 iax kernel: Excessive leakage detected on module 8: 0 volts (00) after 125 ms Dec 24 13:20:39 iax kernel: ProSLIC module 8 failed leakage test. Check for short circuit Dec 24 13:20:39 iax kernel: Power alarm on module 8, resetting! Dec 24 13:20:39 iax kernel: Power alarm on module 8, resetting! Dec 24 13:20:39 iax kernel: !!!!!!! RING_OSC iREG 14 = F0 should be 7EF0 Dec 24 13:20:39 iax kernel: !!!!!!! LOOP_CLOSE_TRES iREG 1C = 1 should be 1000 Dec 24 13:20:39 iax kernel: !!!!!!! RING_TRIP_TRES iREG 1D = 8000 should be 3600 Dec 24 13:20:39 iax kernel: !!!!!!! COMMON_MIN_TRES iREG 1E = 0 should be 1000 Dec 24 13:20:39 iax kernel: !!!!!!! COMMON_MAX_TRES iREG 1F = 0 should be 200 Dec 24 13:20:39 iax kernel: !!!!!!! PWR_ALARM_Q1Q2 iREG 20 = 1480 should be 7C0 Dec 24 13:20:39 iax kernel: !!!!!!! PWR_ALARM_Q3Q4 iREG 21 = 37C0 should be 4C00 Dec 24 13:20:39 iax kernel: !!!!!!! PWR_ALARM_Q5Q6 iREG 22 = 3D70 should be 1B80 Dec 24 13:20:39 iax kernel: !!!!!!! LOOP_CLOSURE_FILTER iREG 23 = 3970 should be 8000 Dec 24 13:20:39 iax kernel: !!!!!!! RING_TRIP_FILTER iREG 24 = 78E0 should be 320 Dec 24 13:20:39 iax kernel: !!!!!!! TERM_LP_POLE_Q1Q2 iREG 25 = 8B60 should be 8C Dec 24 13:20:39 iax kernel: !!!!!!! TERM_LP_POLE_Q3Q4 iREG 26 = 6A40 should be 100 Dec 24 13:20:39 iax kernel: !!!!!!! TERM_LP_POLE_Q5Q6 iREG 27 = 8070 should be 10 Dec 24 13:20:39 iax kernel: !!!!!!! CM_BIAS_RINGING iREG 28 = FFFF should be C00 Dec 24 13:20:39 iax kernel: Power alarm on module 8, resetting! Dec 24 13:20:39 iax kernel: !!!!!!! DCDC_MIN_V iREG 29 = FFFF should be C00 Dec 24 13:20:39 iax kernel: !!!!!!! DCDC_XTRA iREG 2A = FFFF should be 1000 Dec 24 13:20:39 iax kernel: !!!!!!! LOOP_CLOSE_TRES_LOW iREG 2B = FFFF should be 1000 Dec 24 13:20:39 iax kernel: !!!!! Init Indirect Registers UNSUCCESSFULLY. Dec 24 13:20:39 iax kernel: Indirect Registers failed verification. Dec 24 13:20:39 iax kernel: Power alarm on module 8, resetting! Dec 24 13:20:39 iax kernel: Excessive leakage detected on module 8: 0 volts (00) after 104 ms Dec 24 13:20:39 iax kernel: ProSLIC module 8 failed leakage test. Check for short circuit Dec 24 13:20:39 iax kernel: Proslic Passed Manual Calibration on Second Attempt Dec 24 13:20:39 iax kernel: Power alarm on module 8, resetting! Dec 24 13:20:39 iax kernel: Power alarm on module 8, resetting! Dec 24 13:20:39 iax kernel: !!!!!!! LOOP_CLOSE_TRES iREG 1C = 1 should be 1000 Dec 24 13:20:39 iax kernel: !!!!!!! RING_TRIP_TRES iREG 1D = 8000 should be 3600 Dec 24 13:20:39 iax kernel: !!!!!!! COMMON_MIN_TRES iREG 1E = 0 should be 1000 Dec 24 13:20:39 iax kernel: !!!!!!! COMMON_MAX_TRES iREG 1F = 0 should be 200 Dec 24 13:20:39 iax kernel: !!!!!!! PWR_ALARM_Q1Q2 iREG 20 = 1480 should be 7C0 Dec 24 13:20:39 iax kernel: !!!!!!! PWR_ALARM_Q3Q4 iREG 21 = 37C0 should be 4C00 Dec 24 13:20:39 iax kernel: !!!!!!! PWR_ALARM_Q5Q6 iREG 22 = 3D70 should be 1B80 Dec 24 13:20:39 iax kernel: !!!!!!! LOOP_CLOSURE_FILTER iREG 23 = 3970 should be 8000 Dec 24 13:20:39 iax kernel: !!!!!!! RING_TRIP_FILTER iREG 24 = 78E0 should be 320 Dec 24 13:20:39 iax kernel: !!!!!!! TERM_LP_POLE_Q1Q2 iREG 25 = 8B60 should be 8C Dec 24 13:20:39 iax kernel: !!!!!!! TERM_LP_POLE_Q3Q4 iREG 26 = 6A40 should be 100 Dec 24 13:20:39 iax kernel: !!!!!!! TERM_LP_POLE_Q5Q6 iREG 27 = 8070 should be 10 Dec 24 13:20:39 iax kernel: !!!!!!! CM_BIAS_RINGING iREG 28 = FF00 should be C00 Dec 24 13:20:39 iax kernel: !!!!!!! DCDC_MIN_V iREG 29 = FFFF should be C00 Dec 24 13:20:39 iax kernel: !!!!!!! DCDC_XTRA iREG 2A = FFFF should be 1000 Dec 24 13:20:39 iax kernel: !!!!!!! LOOP_CLOSE_TRES_LOW iREG 2B = FFFF should be 1000 Dec 24 13:20:39 iax kernel: !!!!! Init Indirect Registers UNSUCCESSFULLY. Dec 24 13:20:39 iax kernel: Indirect Registers failed verification. Dec 24 13:20:39 iax kernel: Port 9: FAILED FXS (FCC) Dec 24 13:20:39 iax kernel: Power alarm on module 8, resetting! Dec 24 13:20:39 iax kernel: Excessive leakage detected on module 9: 0 volts (00) after 228 ms Dec 24 13:20:39 iax kernel: ProSLIC module 9 failed leakage test. Check for short circuit Dec 24 13:20:39 iax kernel: Power alarm on module 8, resetting! Dec 24 13:20:39 iax kernel: !!!!!!! PWR_ALARM_Q1Q2 iREG 20 = C0 should be 7C0 Dec 24 13:20:39 iax kernel: Power alarm on module 8, resetting! Dec 24 13:20:39 iax kernel: !!!!! Init Indirect Registers UNSUCCESSFULLY. Dec 24 13:20:39 iax kernel: Indirect Registers failed verification. Dec 24 13:20:39 iax kernel: Excessive leakage detected on module 9: 0 volts (00) after 59 ms Dec 24 13:20:39 iax kernel: ProSLIC module 9 failed leakage test. Check for short circuit Dec 24 13:20:39 iax kernel: Power alarm on module 8, resetting! Dec 24 13:20:39 iax kernel: Proslic Passed Manual Calibration on Second Attempt Dec 24 13:20:39 iax kernel: Too many power alarms on card 8, NOT resetting! Dec 24 13:20:39 iax kernel: !!!!!!! XMIT_DIGITAL_GAIN iREG 1B = 0 should be 4000 Dec 24 13:20:39 iax kernel: !!!!! Init Indirect Registers UNSUCCESSFULLY. Dec 24 13:20:39 iax kernel: Indirect Registers failed verification. Dec 24 13:20:39 iax kernel: Port 10: FAILED FXS (FCC) Dec 24 13:20:39 iax kernel: Excessive leakage detected on module 10: 0 volts (00) after 35 ms Dec 24 13:20:39 iax kernel: ProSLIC module 10 failed leakage test. Check for short circuit Dec 24 13:20:39 iax kernel: !!!!!!! OSC2_COEF iREG 10 = 70 should be 7870 Dec 24 13:20:39 iax kernel: !!!!!!! LOOP_CLOSE_TRES iREG 1C = 1 should be 1000 Dec 24 13:20:39 iax kernel: !!!!!!! RING_TRIP_TRES iREG 1D = 8000 should be 3600 Dec 24 13:20:39 iax kernel: !!!!!!! COMMON_MIN_TRES iREG 1E = 0 should be 1000 Dec 24 13:20:39 iax kernel: !!!!!!! COMMON_MAX_TRES iREG 1F = 0 should be 200 Dec 24 13:20:39 iax kernel: !!!!!!! PWR_ALARM_Q1Q2 iREG 20 = 1480 should be 7C0 Dec 24 13:20:39 iax kernel: !!!!!!! PWR_ALARM_Q3Q4 iREG 21 = 37C0 should be 4C00 Dec 24 13:20:39 iax kernel: !!!!!!! PWR_ALARM_Q5Q6 iREG 22 = 3D70 should be 1B80 Dec 24 13:20:39 iax kernel: !!!!!!! LOOP_CLOSURE_FILTER iREG 23 = 3970 should be 8000 Dec 24 13:20:39 iax kernel: !!!!!!! RING_TRIP_FILTER iREG 24 = 78E0 should be 320 Dec 24 13:20:39 iax kernel: !!!!!!! TERM_LP_POLE_Q1Q2 iREG 25 = 8B60 should be 8C Dec 24 13:20:39 iax kernel: !!!!!!! TERM_LP_POLE_Q3Q4 iREG 26 = 6A40 should be 100 Dec 24 13:20:39 iax kernel: !!!!!!! TERM_LP_POLE_Q5Q6 iREG 27 = 8070 should be 10 Dec 24 13:20:39 iax kernel: !!!!!!! CM_BIAS_RINGING iREG 28 = FFFF should be C00 Dec 24 13:20:39 iax kernel: !!!!!!! DCDC_MIN_V iREG 29 = FFFF should be C00 Dec 24 13:20:39 iax kernel: !!!!!!! DCDC_XTRA iREG 2A = FFFF should be 1000 Dec 24 13:20:39 iax kernel: !!!!!!! LOOP_CLOSE_TRES_LOW iREG 2B = FFFF should be 1000 Dec 24 13:20:39 iax kernel: !!!!! Init Indirect Registers UNSUCCESSFULLY. Dec 24 13:20:39 iax kernel: Indirect Registers failed verification. Dec 24 13:20:39 iax kernel: Excessive leakage detected on module 10: 0 volts (00) after 143 ms Dec 24 13:20:39 iax kernel: ProSLIC module 10 failed leakage test. Check for short circuit Dec 24 13:20:39 iax kernel: Proslic Passed Manual Calibration on Second Attempt Dec 24 13:20:39 iax kernel: !!!!!!! DTMF_COL_2ND_ARM iREG A = 2 should be 202 Dec 24 13:20:39 iax kernel: !!!!!!! LOOP_CLOSE_TRES iREG 1C = 1 should be 1000 Dec 24 13:20:39 iax kernel: !!!!!!! RING_TRIP_TRES iREG 1D = 8000 should be 3600 Dec 24 13:20:39 iax kernel: !!!!!!! COMMON_MIN_TRES iREG 1E = 0 should be 1000 Dec 24 13:20:39 iax kernel: !!!!!!! COMMON_MAX_TRES iREG 1F = 0 should be 200 Dec 24 13:20:39 iax kernel: !!!!!!! PWR_ALARM_Q1Q2 iREG 20 = 1480 should be 7C0 Dec 24 13:20:39 iax kernel: !!!!!!! PWR_ALARM_Q3Q4 iREG 21 = 37C0 should be 4C00 Dec 24 13:20:39 iax kernel: !!!!!!! PWR_ALARM_Q5Q6 iREG 22 = 3D70 should be 1B80 Dec 24 13:20:39 iax kernel: !!!!!!! LOOP_CLOSURE_FILTER iREG 23 = 3970 should be 8000 Dec 24 13:20:39 iax kernel: !!!!!!! RING_TRIP_FILTER iREG 24 = 78E0 should be 320 Dec 24 13:20:39 iax kernel: !!!!!!! TERM_LP_POLE_Q1Q2 iREG 25 = 8B60 should be 8C Dec 24 13:20:39 iax kernel: !!!!!!! TERM_LP_POLE_Q3Q4 iREG 26 = 6A40 should be 100 Dec 24 13:20:39 iax kernel: !!!!!!! TERM_LP_POLE_Q5Q6 iREG 27 = 8070 should be 10 Dec 24 13:20:39 iax kernel: !!!!!!! CM_BIAS_RINGING iREG 28 = FFFF should be C00 Dec 24 13:20:39 iax kernel: !!!!!!! DCDC_MIN_V iREG 29 = FFFF should be C00 Dec 24 13:20:39 iax kernel: !!!!!!! DCDC_XTRA iREG 2A = FFFF should be 1000 Dec 24 13:20:39 iax kernel: !!!!!!! LOOP_CLOSE_TRES_LOW iREG 2B = FFFF should be 1000 Dec 24 13:20:39 iax kernel: !!!!! Init Indirect Registers UNSUCCESSFULLY. Dec 24 13:20:39 iax kernel: Indirect Registers failed verification. Dec 24 13:20:39 iax kernel: Port 11: FAILED FXS (FCC) Dec 24 13:20:39 iax kernel: Excessive leakage detected on module 11: 0 volts (00) after 244 ms Dec 24 13:20:39 iax kernel: ProSLIC module 11 failed leakage test. Check for short circuit Dec 24 13:20:39 iax kernel: Port 12: Installed -- AUTO FXS/DPO Dec 24 13:20:39 iax kernel: Excessive leakage detected on module 12: 0 volts (00) after 54 ms Dec 24 13:20:39 iax kernel: ProSLIC module 12 failed leakage test. Check for short circuit Dec 24 13:20:39 iax kernel: Port 13: Installed -- AUTO FXS/DPO Dec 24 13:20:39 iax kernel: Excessive leakage detected on module 13: 0 volts (00) after 409 ms Dec 24 13:20:39 iax kernel: ProSLIC module 13 failed leakage test. Check for short circuit Dec 24 13:20:39 iax kernel: !!!!!!! DCDC_MIN_V iREG 29 = 0 should be C00 Dec 24 13:20:39 iax kernel: !!!!! Init Indirect Registers UNSUCCESSFULLY. Dec 24 13:20:39 iax kernel: Indirect Registers failed verification. Dec 24 13:20:39 iax kernel: Excessive leakage detected on module 13: 0 volts (00) after 268 ms Dec 24 13:20:39 iax kernel: ProSLIC module 13 failed leakage test. Check for short circuit Dec 24 13:20:39 iax kernel: Port 14: Installed -- MANUAL FXS Dec 24 13:20:39 iax kernel: Excessive leakage detected on module 14: 0 volts (00) after 119 ms Dec 24 13:20:39 iax kernel: ProSLIC module 14 failed leakage test. Check for short circuit Dec 24 13:20:39 iax kernel: Power alarm on module 14, resetting! Dec 24 13:20:39 iax kernel: Port 15: Installed -- AUTO FXS/DPO Dec 24 13:20:39 iax kernel: Excessive leakage detected on module 15: 0 volts (00) after 231 ms Dec 24 13:20:39 iax kernel: ProSLIC module 15 failed leakage test. Check for short circuit Dec 24 13:20:39 iax kernel: Power alarm on module 14, resetting! Dec 24 13:20:39 iax kernel: Port 16: Installed -- AUTO FXS/DPO Dec 24 13:20:39 iax kernel: Power alarm on module 14, resetting! Dec 24 13:20:39 iax kernel: Port 17: Installed -- AUTO FXO (FCC mode) Dec 24 13:20:39 iax kernel: Power alarm on module 14, resetting! Dec 24 13:20:39 iax kernel: Port 18: Installed -- AUTO FXO (FCC mode) Dec 24 13:20:39 iax kernel: Port 19: Installed -- AUTO FXO (FCC mode) Dec 24 13:20:39 iax kernel: Power alarm on module 14, resetting! Dec 24 13:20:39 iax kernel: Port 20: Installed -- AUTO FXO (FCC mode) Dec 24 13:20:39 iax kernel: Port 21: Not installed Dec 24 13:20:39 iax kernel: Port 22: Not installed Dec 24 13:20:39 iax kernel: Port 23: Not installed Dec 24 13:20:39 iax kernel: Power alarm on module 14, resetting! Dec 24 13:20:39 iax kernel: Port 24: Not installed Dec 24 13:20:39 iax kernel: Found a Wildcard TDM: Wildcard TDM2400P (24 modules) [EMAIL PROTECTED] /]# uname -a FreeBSD iax.nlink.com.br 6.3-RC1 FreeBSD 6.3-RC1 #0: Tue Nov 27 00:59:35 UTC 2007 [EMAIL PROTECTED]:/usr/obj/usr/src/sys/SMP i386 Paulo. Oleksandr Tymoshenko escreveu, Em 30/10/2007 20:31: > I finished the first version of tdm24xxp driver today. > It detects TDM800 card fine, though no audio/calls has been tested > yet. If you have the hardware and time to try it - please, grab > zaptel-1.4 branch from svn, or download the latest snapshot: > http://pbxpress.com/~gonzo/zaptel-bsd-1.4.tar.gz > and give it a try. > > _______________________________________________ --Bandwidth and Colocation Provided by http://www.api-digital.com-- Asterisk-BSD mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-bsd
