Hi Edrich,
What is the current status of those CICs, with ss7 linestat?
Idle, Remote Maintenance Blocked, ...
What messages are displayed on the console?
A.
On 12/14/2010 03:52 PM, Edrich de Lange wrote:
Good morning
I have an issue on one of the links where I have the last 8 cics not
functioning.
Can anyone provide details on what may cause this? It works perfectly
fine on my other link.
I have had the provider also check all their termination equipment,
and that seems to not be the issue. the card has been replaced aswell.
Kind regards
On Mon, Dec 13, 2010 at 10:41 AM, Edrich de Lange<[email protected]> wrote:
Oh, Im using chan_ss7 now.
Those channels are up on my side though.(says idle)
Kind regards
On Mon, Dec 13, 2010 at 10:40 AM, Edrich de Lange<[email protected]> wrote:
Ok, its working fine.
One problem, for some reason the last 8 cics dont come up on the
remote side, and after a while Im getting these errors
[Dec 13 10:38:54] WARNING[4051]: l4isup.c:4803 l4isup_event: Received
CIC=59 for unequipped circuit (typ=RSC), link 'l1'.
[Dec 13 10:38:54] WARNING[4051]: l4isup.c:4803 l4isup_event: Received
CIC=56 for unequipped circuit (typ=RSC), link 'l1'.
[Dec 13 10:38:54] WARNING[4051]: l4isup.c:4803 l4isup_event: Received
CIC=60 for unequipped circuit (typ=RSC), link 'l1'.
[Dec 13 10:38:54] WARNING[4051]: l4isup.c:4803 l4isup_event: Received
CIC=62 for unequipped circuit (typ=RSC), link 'l1'.
[Dec 13 10:38:54] WARNING[4051]: l4isup.c:4803 l4isup_event: Received
CIC=63 for unequipped circuit (typ=RSC), link 'l1'.
[Dec 13 10:38:54] WARNING[4051]: l4isup.c:4803 l4isup_event: Received
CIC=61 for unequipped circuit (typ=RSC), link 'l1'.
[Dec 13 10:38:54] WARNING[4051]: l4isup.c:4803 l4isup_event: Received
CIC=58 for unequipped circuit (typ=RSC), link 'l1'.
[Dec 13 10:38:54] WARNING[4051]: l4isup.c:4803 l4isup_event: Received
CIC=57 for unequipped circuit (typ=RSC), link 'l1'.
Kind regards
On Sat, Dec 11, 2010 at 8:01 AM, bipin singh<[email protected]> wrote:
Hi
Try it
adjpointcode=1368
defaultdpc=1368
and also not set same acp dcp for two links .
On Fri, Dec 10, 2010 at 11:11 PM, Edrich de Lange<[email protected]> wrote:
Good day
I have a setup using a 4 port Digium Card,Asterisk
1.6.2.15,libss7-1.0.2,dahdi-linux-complete-2.4.0
My dahdi config looks like so :
# Span 2: TE4/0/2 "T4XXP (PCI) Card 0 Span 2" HDB3/CCS/CRC4
span=2,2,0,ccs,hdb3
# termtype: te
bchan=32-46,48-62
mtp2=47
#echocanceller=mg2,32-46,48-62
(the other spans are disabled)
[channels]
signaling=ss7 ;this is ss7 signaling
ss7type=itu ;using the ITU variant
;ss7_called_nai=dynamic ;NAI for outgoing calls
;ss7_calling_nai=dynamic ;NAI for incoming calls
ss7_internationalprefix= ;international prefix value for incoming calls
ss7_nationalprefix= ;national prefix value for incoming calls
ss7_subscriberprefix= ;subscriber prefix value for incoming
calls
ss7_unknownprefix= ;unknown prefix value for incoming calls
ss7_explicitacm=yes
ss7_explictacm=yes
group=1
context=ss7
linkset=1
pointcode=720 ;the point code for this system...aka
SPC
adjpointcode=1832 ;the point code for the system
that we are signaling to... aka APC
defaultdpc=1368 ;the point code for the system
that the CICs will be negotiated with...aka DPC
networkindicator=national_spare ;NI value for MTP3
cicbeginswith=32 ;the starting value of the CICs
channel=32-46
cicbeginswith=48
channel=48-62 ;the channels that are CICs
sigchan=47 ;the signaling channel
The Links come up. It seems fine.
When I make a call to the link I get the following on the asterisk CLI
Unhandled optional parameter 0x8 'Optional forward call indicator'
[0x0 ]
Unhandled optional parameter 0x31 'Propagation Delay Counter'
[0x0 0x5a ]
Unhandled optional parameter 0x3f 'Location Number'
[0x84 0x93 0x72 0x38 0x0 0x10 0x7 0x0 0x0 0x0 ]
Unhandled optional parameter 0x39 'Parameter Compatibility Information'
[0x31 0xd0 0x3f 0xc0 ]
[Dec 10 19:36:12] WARNING[3627]: chan_dahdi.c:11850 ss7_linkset: IAM
on unconfigured CIC 6
[Dec 10 19:36:13] WARNING[3627]: chan_dahdi.c:12142 ss7_linkset: RLC
on unconfigured CIC 6
It doesnt seem to trigger even the extentions.
I cant get the Chan_ss7 to work, as My DPC and APC are different(if im
mistaken please assist, I would gladly try chan_ss7)
I just need to get the incoming calls working urgently.
Any assistance will be greatly appreciated.
Kind regards
Edrich de Lange
--
_____________________________________________________________________
-- Bandwidth and Colocation Provided by http://www.api-digital.com --
asterisk-ss7 mailing list
To UNSUBSCRIBE or update options visit:
http://lists.digium.com/mailman/listinfo/asterisk-ss7
--
BIPIN RAGHUVANSHI
OPERATION HEAD
ASTERISK (DEVELOPMENT AND RESEARCH)
WWW.EHORIZONS.IN
011-32323262
011-46334633
--
_____________________________________________________________________
-- Bandwidth and Colocation Provided by http://www.api-digital.com --
asterisk-ss7 mailing list
To UNSUBSCRIBE or update options visit:
http://lists.digium.com/mailman/listinfo/asterisk-ss7
--
_____________________________________________________________________
-- Bandwidth and Colocation Provided by http://www.api-digital.com --
asterisk-ss7 mailing list
To UNSUBSCRIBE or update options visit:
http://lists.digium.com/mailman/listinfo/asterisk-ss7
