Hi, I tried it libss7 before, but there i've got problems receiving SAM messages.
2012/3/3 bipin singh <[email protected]>: > Hi , > If possible try libss7. > > > On Sat, Mar 3, 2012 at 2:06 AM, Simon Handschin <[email protected]> > wrote: >> >> Hi thank you for your fast answer. >> Its about carrier pre selection eg i make a call from an external phone >> (not connected to the server) with our cpc like 1234. >> >> 12340041441234567 >> >> The Call will be routet to our server from the provider. They have enbloc >> enabled. >> >> Dialplan is like exten => _12340041xxxxxxxxxx (for switzerland and i know >> digits lenght) >> >> Its the # key because of the enbloc from our Provider? >> >> Greetings, >> >> Simon >> >> Am 02.03.2012 20:37 schrieb <[email protected]>: >> >>> Define "callbycall" number. What is the callflow? >>> Accepted where, by what equipment? >>> Are you trying to describe something which has to do with overlap vs. >>> enbloc >>> dialing in a call-through scenario with digit collection on Asterisk or >>> is >>> this a one stage call where the call enters and leaves Asterisk in one >>> go? >>> By what means is this ISDN phone connected to the Asterisk machine? >>> How does the dialplan look like? >>> >>> >>> >>> > -----Ursprüngliche Nachricht----- >>> > Von: [email protected] [mailto:asterisk-ss7- >>> > [email protected]] Im Auftrag von Simon Handschin >>> > Gesendet: Freitag, 2. März 2012 20:07 >>> > An: [email protected] >>> > Betreff: [asterisk-ss7] chan_ss7 incoming callbycall call problems >>> > >>> > Hello everyone. >>> > >>> > I have a problem. I have a callbycall number routet to our E1 Server. >>> > If i Dial from my ISDN Phone to this callbycall number the call only >>> > get >>> > acceptet if i press # key. Normal dial in and out works on our server >>> > just >>> if >>> > dial with call by call it did not work. >>> > >>> > I Use >>> > >>> > Sangoma A104 Card (Only 1 Port is Used) >>> > >>> > Asterisk 1.8.9.3 >>> > Dahdi 2.6 >>> > chan_ss7 2.1.0 >>> > Wanpipe 3.5.25 >>> > >>> > dahdi systems.conf >>> > >>> > #autogenerated by /usr/sbin/wancfg_dahdi do not hand edit #autogenrated >>> > on >>> > 2012-03-02 #Dahdi Channels Configurations #For detailed Dahdi options, >>> view >>> > /etc/dahdi/system.conf.bak loadzone=de defaultzone=de >>> > >>> > #Sangoma A104 port 1 [slot:3 bus:13 span:1] <wanpipe1> >>> > span=1,0,0,ccs,hdb3,crc4 >>> > bchan=1-31 >>> > echocanceller=mg2,2-31 >>> > #hardhdlc=1 >>> > >>> > wanpipe1.conf >>> > >>> > >>> > #================================================ >>> > # WANPIPE1 Configuration File >>> > #================================================ >>> > # >>> > # Date: Wed Dec 6 20:29:03 UTC 2006 >>> > # >>> > # Note: This file was generated automatically >>> > # by /usr/local/sbin/setup-sangoma program. >>> > # >>> > # If you want to edit this file, it is >>> > # recommended that you use wancfg program >>> > # to do so. >>> > #================================================ >>> > # Sangoma Technologies Inc. >>> > #================================================ >>> > >>> > [devices] >>> > wanpipe1 = WAN_AFT_TE1, Comment >>> > >>> > [interfaces] >>> > w1g1 = wanpipe1, , TDM_VOICE, Comment >>> > >>> > [wanpipe1] >>> > CARD_TYPE = AFT >>> > S514CPU = A >>> > CommPort = PRI >>> > AUTO_PCISLOT = NO >>> > PCISLOT = 3 >>> > PCIBUS = 13 >>> > FE_MEDIA = E1 >>> > FE_LCODE = HDB3 >>> > FE_FRAME = CRC4 >>> > FE_LINE = 1 >>> > TE_CLOCK = MASTER >>> > TE_REF_CLOCK = 0 >>> > TE_SIG_MODE = CCS >>> > TE_HIGHIMPEDANCE = NO >>> > TE_RX_SLEVEL = 430 >>> > HW_RJ45_PORT_MAP = DEFAULT >>> > LBO = 120OH >>> > FE_TXTRISTATE = NO >>> > MTU = 1500 >>> > UDPPORT = 9000 >>> > TTL = 255 >>> > IGNORE_FRONT_END = NO >>> > TDMV_SPAN = 1 >>> > TDMV_DCHAN = 0 >>> > TE_AIS_MAINTENANCE = NO #NO: defualt YES: Start port in AIS >>> > Blue Alarm and keep line down >>> > #wanpipemon -i w1g1 -c Ttx_ais_off to >>> disable >>> > AIS maintenance mode >>> > >>> > #wanpipemon >>> -i w1g1 -c >>> > Ttx_ais_on to enable AIS maintenance mode >>> > TDMV_HW_DTMF = NO # YES: receive dtmf events from >>> hardware >>> > TDMV_HW_FAX_DETECT = NO # YES: receive fax 1100hz >>> events from >>> > hardware >>> > HWEC_OPERATION_MODE = OCT_NORMAL # OCT_NORMAL: echo cancelation >>> > enabled with nlp (default) >>> > >>> # OCT_SPEECH: >>> > improves software tone detection by disabling NLP (echo possible) >>> > >>> # >>> > OCT_NO_ECHO:disables echo cancelation but allows VQE/tone functions. >>> > HWEC_DTMF_REMOVAL = NO # NO: default YES: remove dtmf out of >>> > incoming media (must have hwdtmf enabled) >>> > HWEC_NOISE_REDUCTION = NO # NO: default YES: reduces noise on >>> > the line - could break fax >>> > HWEC_ACUSTIC_ECHO = NO # NO: default YES: enables acustic >>> > echo cancelation >>> > HWEC_NLP_DISABLE = NO # NO: default YES: guarantees >>> > software tone detection (possible echo) >>> > HWEC_TX_AUTO_GAIN = 0 # 0: disable -40-0: default tx audio >>> > level to be maintained (-20 default) >>> > HWEC_RX_AUTO_GAIN = 0 # 0: disable -40-0: default tx audio >>> > level to be maintained (-20 default) >>> > HWEC_TX_GAIN = 0 # 0: disable -24-24: db values >>> > to >>> be >>> > applied to tx signal >>> > HWEC_RX_GAIN = 0 # 0: disable -24-24: db values >>> > to >>> be >>> > applied to tx signal >>> > >>> > [w1g1] >>> > ACTIVE_CH = ALL >>> > TDMV_HWEC = NO >>> > MTU = 8 >>> > >>> > >>> > ss7.conf >>> > >>> > [linkset-siuc] >>> > enabled => yes >>> > enable_st => no >>> > use_connect => no >>> > hunting_policy => even_mru >>> > context => ss7 >>> > language => de >>> > t35 => 4000,st >>> > subservice => auto >>> > variant => ITU >>> > >>> > >>> > [link-l1] >>> > linkset => siuc >>> > channels => 2-31 >>> > schannel => 1 >>> > firstcic => 1 >>> > enabled => yes >>> > sltm => no >>> > sls=0 >>> > echocancel => no >>> > echocan_train => 350 >>> > echocan_taps => 128 >>> > >>> > [host-SS7-1] >>> > if-1 => 10.1.40.71 >>> > enabled => yes >>> > opc => 1601 >>> > dpc => siuc:300 >>> > links => l1:1 ;span 1 of dahdi/system.conf >>> > ;globaltitle => 0x00, 0x03, 0x01, 7773 >>> > ssn => 7 >>> > >>> > >>> > Anyone got an idea about this? >>> > >>> > Greetings >>> > >>> > Simon >>> > >>> > -- >>> > _____________________________________________________________________ >>> > -- Bandwidth and Colocation Provided by http://www.api-digital.com -- >>> > >>> > asterisk-ss7 mailing list >>> > To UNSUBSCRIBE or update options visit: >>> > http://lists.digium.com/mailman/listinfo/asterisk-ss7 >>> >>> >>> -- >>> _____________________________________________________________________ >>> -- Bandwidth and Colocation Provided by http://www.api-digital.com -- >>> >>> asterisk-ss7 mailing list >>> To UNSUBSCRIBE or update options visit: >>> http://lists.digium.com/mailman/listinfo/asterisk-ss7 >> >> >> -- >> _____________________________________________________________________ >> -- Bandwidth and Colocation Provided by http://www.api-digital.com -- >> >> asterisk-ss7 mailing list >> To UNSUBSCRIBE or update options visit: >> http://lists.digium.com/mailman/listinfo/asterisk-ss7 > > > > > -- > BIPIN RAGHUVANSHI > OPERATION HEAD > ASTERISK (DEVELOPMENT AND RESEARCH) > WWW.EHORIZONS.IN > 011-32323262 > 011-46334633 > > -- > _____________________________________________________________________ > -- Bandwidth and Colocation Provided by http://www.api-digital.com -- > > asterisk-ss7 mailing list > To UNSUBSCRIBE or update options visit: > http://lists.digium.com/mailman/listinfo/asterisk-ss7 -- _____________________________________________________________________ -- Bandwidth and Colocation Provided by http://www.api-digital.com -- asterisk-ss7 mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-ss7
