Can anyone work out why my callerid doesn't work on my isdn4Linux with asterisk (or without asterisk for that matter)...
This used to work fine, and I am quite confident that the telco is sending callerid information (because they always do on all ISDN lines standard, only extra cost on POTS lines). This is the information from dmesg, whether asterisk is running or not: isdn_net: Incoming call without OAD, assuming '0' isdn_net: call from 0 -> 0 xxxxxxxx ignored where xxxxxxxx is my local phone number without area code I turned on the maximum isdn debugging, and here is the output when I dial in, at this time, asterisk was not running... 29:42.76 Card1 tiger: i1 2 80 29:42.76 Card1 ISAC interrupt 80 29:42.76 Card1 isac_empty_fifo cnt 4 02 81 01 3B 29:42.76 Card1 <- PH_DATA: RR[1](nr 29)C (sapi 0, tei 64) HEX: 02 81 01 3B 29:42.76 frame network->user SFrame with tei 64 29:42.78 Card1 tiger: i1 2 80 29:42.78 Card1 ISAC interrupt 80 29:42.78 Card1 isac_empty_fifo cnt 4 00 81 01 3B 29:42.78 Card1 <- PH_DATA: RR[1](nr 29)R (sapi 0, tei 64) HEX: 00 81 01 3B 29:42.78 frame network->user SFrame with tei 64 29:45.87 Card1 tiger: i1 2 80 29:45.87 Card1 ISAC interrupt 80 29:45.87 Card1 isac_empty_fifo cnt 31 02 FF 03 08 01 03 05 A1 04 03 80 90 A3 18 01 8A 70 09 C1 39 36 39 34 31 31 30 30 7D 02 91 81 29:45.87 Card1 <- PH_DATA: UI[0]C (sapi 0, tei 127) HEX: 02 FF 03 08 01 03 05 A1 04 03 80 90 A3 18 01 8A 70 09 C1 39 36 39 34 31 31 30 30 7D 02 91 81 29:45.87 frame network->user broadcast callref 3 caller size 28 message type SETUP Sending complete Bearer capability octet 3 10000000 octet 4 10010000 octet 5 10100011 Channel identification octet 3 10001010 Called party number octet 3 11000001 number digits 96941100 High layer compatibility octet 3 10010001 octet 4 10000001 29:45.87 DCh Q.921 State ST_L2_1 Event EV_L2_UI 29:45.87 Ch0 callc State ST_NULL Event EV_SETUP_IND 29:45.87 Ch0 callc ChangeState ST_IN_WAIT_LL 29:45.87 Ch0 HL->LL STAT_ICALL 29:45.87 Ch0 LL->HL statcallb ret=0 29:45.87 L3DC State ST_L3_LC_REL Event EV_RELEASE_REQ no routine 29:45.87 Ch0 callc ChangeState ST_NULL 29:49.92 Card1 tiger: i1 2 80 29:49.92 Card1 ISAC interrupt 80 29:49.92 Card1 isac_empty_fifo cnt 31 02 FF 03 08 01 03 05 A1 04 03 80 90 A3 18 01 8A 70 09 C1 39 36 39 34 31 31 30 30 7D 02 91 81 29:49.92 Card1 <- PH_DATA: UI[0]C (sapi 0, tei 127) HEX: 02 FF 03 08 01 03 05 A1 04 03 80 90 A3 18 01 8A 70 09 C1 39 36 39 34 31 31 30 30 7D 02 91 81 29:49.92 frame network->user broadcast callref 3 caller size 28 message type SETUP Sending complete Bearer capability octet 3 10000000 octet 4 10010000 octet 5 10100011 Channel identification octet 3 10001010 Called party number octet 3 11000001 number digits 96941100 High layer compatibility octet 3 10010001 octet 4 10000001 29:49.92 DCh Q.921 State ST_L2_1 Event EV_L2_UI 29:49.92 Ch0 callc State ST_NULL Event EV_SETUP_IND 29:49.92 Ch0 callc ChangeState ST_IN_WAIT_LL 29:49.92 Ch0 HL->LL STAT_ICALL 29:49.92 Ch0 LL->HL statcallb ret=0 29:49.92 L3DC State ST_L3_LC_REL Event EV_RELEASE_REQ no routine 29:49.92 Ch0 callc ChangeState ST_NULL 29:52.80 Card1 tiger: i1 2 80 29:52.80 Card1 ISAC interrupt 80 29:52.80 Card1 isac_empty_fifo cnt 4 00 81 01 3B 29:52.80 Card1 <- PH_DATA: RR[1](nr 29)R (sapi 0, tei 64) HEX: 00 81 01 3B 29:52.80 frame network->user SFrame with tei 64 30:02.83 Card1 tiger: i1 2 80 30:02.83 Card1 ISAC interrupt 80 30:02.83 Card1 isac_empty_fifo cnt 4 00 81 01 3B 30:02.83 Card1 <- PH_DATA: RR[1](nr 29)R (sapi 0, tei 64) HEX: 00 81 01 3B 30:02.83 frame network->user SFrame with tei 64 Any hints/clues would be very handy, as it is kind of annoying to have callerid available but not be able to make use of it... Regards, Adam _______________________________________________ Asterisk-Users mailing list [EMAIL PROTECTED] http://lists.digium.com/mailman/listinfo/asterisk-users