The /var/log/messages lists: kernel: Module 0: Not installed kernel: Module 1: Not installed kernel: Module 2: Not installed Jul 3 22:21:10 kernel: Module 3: Installed -- AUTO FXO (FCC mode) kernel: Found a Wildcard TDM: Wildcard TDM400P REV I (4 modules)
the ztcfg -vv: Zaptel Configuration ====================== Channel map: Channel 04: FXS Loopstart (Default) (Slaves: 04) 1 channels configured. When you try to start asterisk. the following errors appear Jul 4 10:37:59 NOTICE[4015]: res_odbc.c:518 load_module: res_odbc loaded. .........Jul 4 10:37:59 ERROR[4015]: chan_zap.c:6584 mkintf: Signalling requested on channel 4 is FXO Loopstart but line is in FXS Loopstart signalling Jul 4 10:37:59 ERROR[4015]: chan_zap.c:9927 setup_zap: Unable to register channel '4' Jul 4 10:37:59 WARNING[4015]: loader.c:402 __load_resource: chan_zap.so: load_module failed, returning -1 Jul 4 10:37:59 WARNING[4015]: loader.c:523 load_modules: Loading module chan_zap.so failed! Any ideas? --- Rich Adamson <[EMAIL PROTECTED]> wrote: > > I am trying the setup the TDM01B card. 1 FXO. I > > connected it to a regular home line. in the > > /etc/zaptel.conf, I have > > fxsls=4 > > In the /etc/asterisk/zapata.conf > > I have: > > signaling=fxs_ls > > language=en > > group=1 > > context=default > > channel => 4 > > > > When I start asterisk, I get this error: > > ERROR[10376]: chan_zap.c:6584 mkintf; Signaling > > requested on channel 4 is FXO Loopstart but line > is in > > FXS Loopstart Signaling > > > > chan_zap.c:9927 setup_zap: Unable to register > channel > > '4' > > > > Maybe I have something misconfigured. However, I > > triead all combinations and it doesn't seem to > work. > > > > If I take away those lines. Asterisk comes up and > in > > zaptel show command, I see the TDM400P card. > > Please help. > > Thanks > > What do you see listed in 'dmesg'? > > It should look something like: > Module 0: Installed -- AUTO FXO (FCC mode) > Module 1: Installed -- AUTO FXO (FCC mode) > Module 2: Installed -- AUTO FXO (FCC mode) > Module 3: Installed -- AUTO FXO (FCC mode) > (The above example is from a TDM with four fxo > modules installed.) > > What do you see listed in 'ztcfg -vv'? > > It should look something like: > Channel 01: FXS Kewlstart (Default) (Slaves: 01) > Channel 02: FXS Kewlstart (Default) (Slaves: 02) > Channel 03: FXS Kewlstart (Default) (Slaves: 03) > Channel 04: FXS Kewlstart (Default) (Slaves: 04) > (Again, the above is from a TDM with four fxo > modules, each configured > for Kewlstart, not loopstart.) > > If you're not seeing entries similar to the above, > I'd have to guess > that changes made to /etc/zaptel.conf and > /etc/asterisk/zapata.conf > are probably out of sync. (Meaning changes have been > made to one or > the other without restarting asterisk AND zaptel.) > > > _______________________________________________ > Asterisk-Users mailing list > Asterisk-Users@lists.digium.com > http://lists.digium.com/mailman/listinfo/asterisk-users > To UNSUBSCRIBE or update options visit: > > http://lists.digium.com/mailman/listinfo/asterisk-users > __________________________________________________ Do You Yahoo!? Tired of spam? Yahoo! Mail has the best spam protection around http://mail.yahoo.com _______________________________________________ Asterisk-Users mailing list Asterisk-Users@lists.digium.com http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users