This is inbound FXO's pointed at the autoattendat on our * server. On Wed, 24 Sep 2003, Doug Dimick wrote:
> The configuration shouldn't be much different. Just replace port 1/0/0 > with port 1/0:23, or whatever the voice port your PRI/T1/E1 happens to be. > > PLAR is Private Line Auto Ringdown. You pick up the port and it > automatically dials. Think Batphone. In the configuration provided below > it is configured so that anyone picking up the phone on the voice port > (like an incoming phone call) will automatically dial 9999, which then > would connect to the IP address of Asterisk with H.323. > > -d > > > > Message: 4 > > Date: Wed, 24 Sep 2003 16:31:17 +0000 (GMT) > > From: Sean Figgins <[EMAIL PROTECTED]> > > To: [EMAIL PROTECTED] > > Subject: RE: [Asterisk-Users] Cisco 2600 and ASTERISK > > Reply-To: [EMAIL PROTECTED] > > > > > > That is about what I have been seing for help. Has anyone any clue what > > to di with a 2600 that has a T1 adapter on a high-density high-density > > voice port adapter? > > > > BTW... Because I am lazy, what does plar do? > > > > -Sean > > > > On Wed, 24 Sep 2003, Brian West wrote: > > > >> This is simple to do.. > >> > >> voice-port 1/0/0 > >> connection plar 9999 > >> ! > >> voice-port 1/0/1 > >> connection plar 9999 > >> ! > >> dial-peer voice 1000 voip > >> max-conn 4 > >> destination-pattern 9999 > >> req-qos guaranteed-delay > >> codec g711ulaw > >> ip precedence 5 > >> no vad > >> session target ipv4:x.x.x.x > >> ! > >> > >> in h323.conf set the context=blah > >> > >> [blah] > >> > >> exten => 9999,1,Goto(s,1) > >> > >> > >> Done... its really that simple. I have this working with a 2600 and a > >> 1750. > >> > >> bkw > >> > >> On Wed, 24 Sep 2003, Joseph Finley wrote: > >> > >> > I too would like to see it. I've tried many times with the help of a > >> few > >> > and never got it to work. It always results in a fast busy. > >> > > >> > Joe > >> > > >> > > >> > -----Original Message----- > >> > From: [EMAIL PROTECTED] > >> > [mailto:[EMAIL PROTECTED] On Behalf Of Bartosz > >> Jozwiak > >> > Sent: Wednesday, September 24, 2003 9:46 AM > >> > To: ASTERISK USERS > >> > Subject: [Asterisk-Users] Cisco 2600 and ASTERISK > >> > > >> > > >> > Hello, > >> > > >> > Could somebody tell me if I can connect CISCO 2600 router with support > >> of > >> > H.323 to Asterisk ? > >> > If it is possible could somebody tell me how to do it. > >> > I would like to document it and put on some website so everyone can > >> see it. > >> > > >> > Regards, > >> > > >> > -- bart > >> > > >> > > >> _______________________________________________ > >> Asterisk-Users mailing list > >> [EMAIL PROTECTED] > >> http://lists.digium.com/mailman/listinfo/asterisk-users > >> > > > > > > > > --__--__-- > > > > _______________________________________________ > > Asterisk-Users mailing list > > [EMAIL PROTECTED] > > http://lists.digium.com/mailman/listinfo/asterisk-users > > > > > > End of Asterisk-Users Digest > > > _______________________________________________ > Asterisk-Users mailing list > [EMAIL PROTECTED] > http://lists.digium.com/mailman/listinfo/asterisk-users > _______________________________________________ Asterisk-Users mailing list [EMAIL PROTECTED] http://lists.digium.com/mailman/listinfo/asterisk-users