Hello, Below the IOS config file. Should I disable RFC3389 ??? If yes HOW ??
Show running-config ------------------------- version 12.2 service timestamps debug datetime msec service timestamps log datetime msec service password-encryption service internal ! hostname UK-GW01 ! enable secret 5 $1$Q7QI$wgMvyRdFRxalCmgcEv7A81 ! ! ! resource-pool disable ! ip subnet-zero no ip domain lookup ! ! isdn switch-type primary-net5 ! voice call carrier capacity active ! ! ! ! ! ! ! ! ! mta receive maximum-recipients 0 ! controller E1 0 clock source free-running pri-group timeslots 1-31 ! controller E1 1 clock source line secondary 1 pri-group timeslots 1-31 ! controller E1 2 clock source line secondary 2 pri-group timeslots 1-31 ! controller E1 3 clock source line secondary 3 pri-group timeslots 1-31 ! ! ! interface Ethernet0 no ip address shutdown ! interface Serial0 no ip address shutdown no fair-queue clockrate 2015232 ! interface Serial1 no ip address shutdown no fair-queue clockrate 2015232 ! interface Serial2 no ip address shutdown no fair-queue clockrate 2015232 ! interface Serial3 no ip address shutdown no fair-queue clockrate 2015232 ! interface Serial0:15 no ip address ip mroute-cache isdn switch-type primary-net5 isdn incoming-voice modem no cdp enable ! interface Serial1:15 no ip address ip mroute-cache isdn switch-type primary-net5 isdn incoming-voice modem no cdp enable ! interface Serial2:15 no ip address ip mroute-cache isdn switch-type primary-net5 isdn incoming-voice modem no cdp enable ! interface Serial3:15 no ip address ip mroute-cache isdn switch-type primary-net5 isdn incoming-voice modem no cdp enable ! interface FastEthernet0 ip address 213.232.105.12 255.255.255.0 duplex auto speed auto ! ip classless ip route 0.0.0.0 0.0.0.0 213.232.105.254 no ip http server ! ! ! snmp-server community public RO snmp-server enable traps tty ! call rsvp-sync ! voice-port 0:D ! voice-port 1:D ! voice-port 2:D ! voice-port 3:D ! ! mgcp profile default ! dial-peer cor custom ! ! ! dial-peer voice 100 pots application session direct-inward-dial port 0:D ! dial-peer voice 101 pots application session direct-inward-dial port 1:D ! dial-peer voice 102 pots application session direct-inward-dial port 2:D ! dial-peer voice 103 pots application session direct-inward-dial port 3:D ! dial-peer voice 300 voip application session destination-pattern 1879 progress_ind setup enable 3 session protocol sipv2 session target ipv4:62.39.85.18:5060 dtmf-relay rtp-nte codec g711alaw bytes 80 ! dial-peer voice 201 voip application session destination-pattern 1[6,7,9].. progress_ind setup enable 3 session protocol sipv2 session target sip-server dtmf-relay rtp-nte codec g711alaw bytes 80 ! dial-peer voice 204 voip application session destination-pattern 18[0-6,8,9]. progress_ind setup enable 3 session protocol sipv2 session target sip-server dtmf-relay rtp-nte codec g711alaw bytes 80 ! dial-peer voice 206 voip application session destination-pattern 187[0-8] progress_ind setup enable 3 session protocol sipv2 session target sip-server dtmf-relay rtp-nte codec g711alaw bytes 80 ! gateway timer receive-rtcp 1000 ! sip-ua no oli sip-server ipv4:62.39.85.19:5060 ! ! line con 0 line aux 0 line vty 0 4 password 7 094D4210160B login ! end On Mon, 2003-09-29 at 14:17, Low, Adam wrote: > I wouldn't expect you to be using RFC3389 if your using A-law, can you include your > IOS version and IOS config file ... > > I have not specified any allow's or disallow's in my * config for the codecs with my > 5300, I also use Cisco 79xx phones and I use the option within the phones config > file to select the preffered codec and when I change this to G.729/A-law/U-law all > works perfectly for me. > > > -----Original Message----- > > From: Areski [mailto:[EMAIL PROTECTED] > > Sent: 29 September 2003 14:02 > > To: [EMAIL PROTECTED] > > Subject: [Asterisk-Users] cisco AS5300 : problem configuration > > > > > > Hi all !!! > > > > > > > > I m trying to setup a cisco AS5300 and I ve got some problem !!! > > > > During a call test I m getting this error message all the time. > > > > NOTICE[15371]: File rtp.c, Line 263 (process_rfc3389): RFC3389 support > > incomplete. Turn off on client if possible > > > > > > > > > > [general] > > port = 5060 ; Port to bind to > > bindaddr = 0.0.0.0 ; Address to bind to > > context = kiki ; Default for incoming calls > > allow=alaw ; Allow codecs in order of preference > > ;allow=ilbc > > ;allow=all > > > > > > [gw] > > type=user > > host=213.232.xxx.xx > > dtmfmode=rfc2833 ; Choices are inband, rfc2833, or info > > context=kiki > > > > > > ---------------------- > > > > Also when I allow "all" for the codecs that's doesn't work and in the > > SIP trace, it seems that Asterisk doesn't choose the > > appropriated codec. > > WHY ??? I really see the GW asking to use ulaw !!! > > > > > > ---------- > > When I try to setup a AGI script, for example: > > SAY DIGITS 7565 "" > > I can hear the first number 7 but nothing else !?! > > > > > > > > > > > > Any ideas about those problems ??? > > Thx for your helps, > > Areski > > > > _______________________________________________ > > Asterisk-Users mailing list > > [EMAIL PROTECTED] > > http://lists.digium.com/mailman/listinfo/asterisk-users > > > > > ********* DISCLAIMER ********* > > This message and any attachment are confidential and may be privileged or otherwise > protected from disclosure and may include proprietary information. If you are not > the intended recipient, please telephone or email the sender and delete this message > and any attachment from your system. If you are not the intended recipient you must > not copy this message or attachment or disclose the contents to any other person > > > _______________________________________________ > Asterisk-Users mailing list > [EMAIL PROTECTED] > http://lists.digium.com/mailman/listinfo/asterisk-users _______________________________________________ Asterisk-Users mailing list [EMAIL PROTECTED] http://lists.digium.com/mailman/listinfo/asterisk-users
