Can anyone please provide some help. I have installed an AVM fritz card on
an asterisk box ([EMAIL PROTECTED] version 1.5). I have installed the card
driver and chan_capi-cm-0.6. According to the installations guide I can now
see that the CAPI channel in asterisk is up,
*CLI> capi info
Contr1: 2 B channels total, 2 B channels free.
I set up a trunk and the dialstring includes the following,
CAPI/g1/0299546476:b${EXTEN},30,r
My capi.conf is,
[general]
nationalprefix=0
internationalprefix=00
rxgain=0.8
txgain=0.8
;ulaw=yes ;set this, if you live in u-law world instead of a-law
; interface sections ...
[ISDN1] ;this example interface gets name 'ISDN1' and may be any
;name not starting with 'g' or 'contr'.
;ntmode=yes ;if isdn card operates in nt mode, set this to yes
isdnmode=msn ;'MSN' (point-to-multipoint) or 'DID' (direct inward dial)
;when using NT-mode, ptp should be set in any case
incomingmsn=* ;allow incoming calls to this list of MSNs/DIDs, * == any
;controller=0 ;ISDN4BSD default
;controller=7 ;ISDN4BSD USB default
controller=1 ;capi controller number to use
group=1 ;dialout group
;prefix=0 ;set a prefix to calling number on incoming calls
softdtmf=on ;enable/disable software dtmf detection, recommended for
AVM cards
relaxdtmf=on ;in addition to softdtmf, you can use relaxed dtmf
detection
accountcode= ;Asterisk accountcode to use in CDRs
context=from-trunk
;context=capi-in ;context for incoming calls
holdtype=hold ;when Asterisk puts the call on hold, ISDN HOLD will be
used. If
;set to 'local' (default value), no hold is done and
Asterisk may
;play MOH.
;immediate=yes ;immediate start of pbx with extension 's' if no digits
were
;received on incoming call (no destination number yet)
;echosquelch=1 ;_VERY_PRIMITIVE_ echo suppression
;echocancel=yes ;EICON DIVA SERVER (CAPI) echo cancelation
;(possible values: 'no', 'yes', 'force', 'g164', 'g165')
echocancelold=yes;use facility selector 6 instead of correct 8 (necessary
for older eicon drivers)
;echotail=64 ;echo cancel tail setting
;bridge=yes ;native bridging (CAPI line interconnect) if available
;callgroup=1 ;Asterisk call group
;deflect=1234567 ;deflect incoming calls to 1234567 if all B channels are
busy
devices=2 ;number of concurrent calls on this controller
;(2 makes sense for single BRI, 30 for PRI)
I can't see that a number is assigned to msn, but I read somewhere on this
list that for this latest version of chan_capi this is not required.
I connected the asterisk box to the ISDN line, which belongs to a Hunt group
with number as shown in the dialstring and when ringing that number from an
external line I do not get any tone and asterisk does not log any
indications of incoming calls via the CAPI channel
Can anyone please shed some light on what do I need to do in order to be
able to receive calls via this setup.
Thanks in advance,
PolAUs
_________________________________________________________________
SEEK: Over 80,000 jobs across all industries at Australia's #1 job site.
http://ninemsn.seek.com.au?hotmail
_______________________________________________
--Bandwidth and Colocation sponsored by Easynews.com --
Asterisk-Users mailing list
Asterisk-Users@lists.digium.com
http://lists.digium.com/mailman/listinfo/asterisk-users
To UNSUBSCRIBE or update options visit:
http://lists.digium.com/mailman/listinfo/asterisk-users