| I have a issue with two Zap clone cards where they used to work. I am using [EMAIL PROTECTED] 2.5 which includes Asterisk 1.24 and Zaptel drivers 1.2.4. The system is a new Intel Celerion machine. I used to have the same cards running in a Intel PIII system. in this system, they worked. In this older system, I was able to call into the machine and call out from it. Now that I have upgraded the entire box, I cannot figure out why the cards are not working or, more correctly, I cannot place or receive calls on them. First, a bit of background. I have been running this new machine for a few weeks now connecting to the PSTN through an IAX provider. I have some 10 phones connected to Asterisk using several DLink DVG-1120M VOIP "routers". Voicemail, paging, etc. all works. I can call into the IAX trunk and call any phone. I have two POTS lines which I intend to keep - the IAX provider charges by the minutes, thus, I would like to use this connection only as a backup when the POTS lines are in use. The Asterisk system is replacing a Nortel Venture setup. So, I am at the final stage of implementation - get the Zap cards working, sell the Venture phone system. Now, I have installed the drivers, setup the /etc/zapata.conf and /etc/asterisk/zapata-auto.conf, etc. I have configured Asterisk with two trunks Zap/1 and Zap/2. For testing, I have setup asterisk to sent calls with the dialing prefix of 9 to the Zap trunks. When I attempt to place a call, I receive the following message: Mar 5 18:20:29 NOTICE[13927] app_dial.c: Unable to create channel of type 'ZAP' (cause 0 - Unknown) ...on both channels. Neither channel even tried to pickup the line. Anyone have any thoughts of where to look? Here are some of details that may be useful: Cards: 02:0b.0 Communication controller: Tiger Jet Network Inc. Tiger3XX Modem/ISDN interface 02:0c.0 Communication controller: Tiger Jet Network Inc. Tiger3XX Modem/ISDN interface /etc/zaptel.conf: # Span 1: WCFXO/0 "Generic Clone Board 1" fxsks=1 # Span 2: WCFXO/1 "Generic Clone Board 2" RED fxsks=2 # Global data loadzone = us defaultzone = us /etc/asterisk/zatata-auto.conf (as generated by genzapataconf): ; callerid=asreceived ; Span 1: WCFXO/0 "Generic Clone Board 1" signalling=fxs_ks ; Note: this is a trunk. Create a ZAP trunk in AMP for Channel 1 context=from-pstn group=0 channel => 1 ; Span 2: WCFXO/1 "Generic Clone Board 2" RED signalling=fxs_ks ; Note: this is a trunk. Create a ZAP trunk in AMP for Channel 2 context=from-pstn group=0 channel => 2 zap show status: asterisk2*CLI> zap show status Description Alarms IRQ bpviol CRC4 Generic Clone Board 1 RED 0 0 0 Generic Clone Board 2 RED 0 0 0 ZTDUMMY/1 1 UNCONFIGUR 0 0 0 (FYI: The Alarms go to OK when the PSTN lines are connected - they were disconnected when I ran this command) zap show channels: sterisk2*CLI> zap show ch channel channels asterisk2*CLI> zap show channels Chan Extension Context Language MusicOnHold pseudo from-pstn en /extension_additional.conf says: OUT_2 = ZAP/2 OUT_1 = ZAP/1 (changing these to Zap/1 or zap/1 makes no difference) Anyone have any thoughts on what I am missing? This must be something simple. Mark Buckaway --- Positive thinking – should never be a substitute for action |
_______________________________________________ --Bandwidth and Colocation provided by Easynews.com --
Asterisk-Users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
