Hello,
I would be delighted to know if you successfully bridged fax calls between
both cards, as I suppose :
- the Junghanns QuadBRI is connected to PSTN,
- at least, one analog fax is connected to the Digium TDM card.
Personnally, I had ongoing problems with fax calls crossing Junghanns BRI
card (from one port to another) :
5 to 15% of fax (incoming or outgoing) are interrupted.
I don't know if that comes from excessive server load or any missing
ressource (PCI bus, ...).
I was thinking about :
- directly connecting faxes on Digium TDM card instead,
- use Junghanns BRI card as a pure access system,
- and bet that voice and fax calls safely use PCI bus.
I couldn't get any clue (nor reply) from Junghanns stating that this card
correctly "switches" ISDN calls.
Learning from your experience would be great for me.
Regards
----- Original Message -----
From: "Chris Earle (CBL)" <[EMAIL PROTECTED]>
To: "Asterisk Users Mailing List - Non-Commercial Discussion"
<asterisk-users@lists.digium.com>
Sent: Thursday, March 16, 2006 6:40 PM
Subject: Re: [Asterisk-Users] module load order for Junghanns qozap and
TDMcard
Okay
think I finally figured this out
it's the modules.conf post-install lines that run ztcfg
You're not supposed to run ztcfg more than once with the multiple zaptel
cards in there .... I kept running it manually (ztcfg -vvvv) not realizing
that after modprobe wcfxs the ztcfg was being run.
So the order that works is
zaptel
qozap
wcfxs (which runs ztcfg, and readies asterisk to run)
If anyone has any comments about this, please post
--
Chris
----- Original Message -----
From: "Chris Earle (CBL)" <[EMAIL PROTECTED]>
To: "'Asterisk Users Mailing List - Non-Commercial Discussion'"
<asterisk-users@lists.digium.com>
Sent: Thursday, March 16, 2006 11:30 AM
Subject: Re: [Asterisk-Users] module load order for Junghanns qozap and
TDMcard
Maybe this will shed some light about what I'm trying to do:
This is some output from dmesg after this load order:
modprobe zaptel
insmod wcfxs
insmod qozap
----
Zapata Telephony Interface Registered on major 196
Freshmaker version: 73
Freshmaker passed register test
Module 0: Installed -- AUTO FXS/DPO
Module 1: Installed -- AUTO FXS/DPO
Module 2: Installed -- AUTO FXS/DPO
Module 3: Installed -- AUTO FXS/DPO
Found a Wildcard TDM: Wildcard TDM400P REV I (4 modules)
PCI: Enabling device 02:01.0 (0000 -> 0003)
qozap: Junghanns.NET quadBRI card configured at mem 0xf889b000 IRQ 17 HZ
100
CardID 0
qozap: S/T ports: 4 [ TE TE TE TE ]
qozap: 1 multiBRI card(s) in this box, 4 BRI ports total.
Zaptel Configuration
======================
SPAN 1: CCS/ AMI Build-out: 399-533 feet (DSX-1)
SPAN 2: CCS/ AMI Build-out: 399-533 feet (DSX-1)
SPAN 3: CCS/ AMI Build-out: 399-533 feet (DSX-1)
SPAN 4: CCS/ AMI Build-out: 399-533 feet (DSX-1)
Channel map:
Channel 01: Individual Clear channel (Default) (Slaves: 01)
Channel 02: Individual Clear channel (Default) (Slaves: 02)
Channel 03: D-channel (Default) (Slaves: 03)
Channel 04: Individual Clear channel (Default) (Slaves: 04)
Channel 05: Individual Clear channel (Default) (Slaves: 05)
Channel 06: D-channel (Default) (Slaves: 06)
Channel 07: Individual Clear channel (Default) (Slaves: 07)
Channel 08: Individual Clear channel (Default) (Slaves: 08)
Channel 09: D-channel (Default) (Slaves: 09)
Channel 10: Individual Clear channel (Default) (Slaves: 10)
Channel 11: Individual Clear channel (Default) (Slaves: 11)
Channel 12: D-channel (Default) (Slaves: 12)
Channel 13: FXO Kewlstart (Default) (Slaves: 13)
Channel 14: FXO Kewlstart (Default) (Slaves: 14)
Channel 15: FXO Kewlstart (Default) (Slaves: 15)
Channel 16: FXO Kewlstart (Default) (Slaves: 16)
16 channels configured.
ZT_SPANCONFIG failed on span 1: Invalid argument (22)
any thoughts?
Chris
----- Original Message -----
From: "Chris Earle (CBL)" <[EMAIL PROTECTED]>
To: "'Asterisk Users Mailing List - Non-Commercial Discussion'"
<asterisk-users@lists.digium.com>
Sent: Thursday, March 16, 2006 10:09 AM
Subject: [Asterisk-Users] module load order for Junghanns qozap and TDM
card
> Hi all,
>
> I'm trying to get a junghanns QuadBRI to coexist in the same machine as
a
> Digium TDM400P card (so I can run the ISDN lines in and bridge with
analog
> phones plugged into the TDM).
>
> I'm having a problem loading the modules. If I follow the BRIstuff
> (0.3.0-pre-1l) install method.... it's to modprobe zaptel, then insmod
> qozap.o
> I'm on Debian 2.4.31.
> That works.
> But then I still need the Digium module. (modprobe wctdm)
> I've tried a few different orders. Sometimes I can get the digium to
load,
> and the qozap.
> but then I get an error on the ztcfg about Span invalid argument
> (could
be
> my zaptel.conf I realize...)
>
> *If* I try loading the wctdm after the zaptel and qozap, the server
freezes!
> Some loop about qozap - dropped audio card....
>
> I don't know if the quadBRI and the TDM are conflicting/sharing the
zaptel
> module, or if I need to modprobe zaptel before each of them? and in
> what
> order?
>
> Any suggestions appreciated... I haven't even got to figuring out what
> I
can
> do with chan_capi, just want to get the BRI card on and stuff.
>
> Thanks for any ideas!
>
>
> --
> Chris Earle
--
This message has been scanned for viruses and dangerous content by
MailScanner, and is believed to be clean.
_______________________________________________
--Bandwidth and Colocation provided by Easynews.com --
Asterisk-Users mailing list
To UNSUBSCRIBE or update options visit:
http://lists.digium.com/mailman/listinfo/asterisk-users
_______________________________________________
--Bandwidth and Colocation provided by Easynews.com --
Asterisk-Users mailing list
To UNSUBSCRIBE or update options visit:
http://lists.digium.com/mailman/listinfo/asterisk-users
