William Piper wrote:
For Problem #2:
I'm not sure what you are asking. Perhaps post your dialplan for this
problem & we will take a look.
bp
On 6/4/06, *M.Hockings* <[EMAIL PROTECTED]
<mailto:[EMAIL PROTECTED]>> wrote:
Problem 2) Incoming sip calls from my voip provider get rejected unless
I allow anyone to connect with sip. I have an incoming route set up with
the right DID that matches the DID that asterisk picks out but it still
rejects the call. Any suggestions about how to get this to work without
allowing any sip connection?
Mike
Hi William, at the bottom of this is my extensions.conf which seems to
be the largest part of the equation for problem #2. I have not applied
any changes to try and resolve my problem #1 yet.
I think the question here is the operation of the following statement in
the [from-sip-external] section:
exten => s,1,GotoIf($["${ALLOW_SIP_ANON}"="yes"]?from-trunk,${DID},1)
If I interpret it correctly it should go to from-trunk,1 if the freePBX
"allow anonymous sip connections" is true and go to
incoming-sip-did-value,1 if it is false ? That is should I be looking
for something like this in the config files to understand how this would
be handled?
exten=>4169671111,1,....
As an aside, is there some beginners guide to understanding dial plans?
My original dial plan (based on things read on voip-info.org) was very
simple and worked as far as it was configured. I have recently gone to
freePBX to try and make the dial plan changes easier and faster however
it adds a lot of gorp like this that I don't understand.
Thanks for any guidance on this,
Mike
; Asterisk Management Portal (AMP)
; Copyright (C) 2004 Coalescent Systems Inc
; dialparties.agi (http://www.sprackett.com/asterisk/)
; Asterisk::AGI (http://asterisk.gnuinter.net/)
; gsm (http://www.ibiblio.org/pub/Linux/utils/compress/!INDEX.short.html)
; loligo sounds (http://www.loligo.com/asterisk/sounds/)
; mpg123 (http://voip-info.org/wiki-Asterisk+config+musiconhold.conf)
; include extension contexts generated from AMP
#include extensions_additional.conf
; Customizations to this dialplan should be made in extensions_custom.conf
; See extensions_custom.conf.sample for an example
#include extensions_custom.conf
[from-trunk] ; just an alias
since VoIP shouldn't be called PSTN
include => from-pstn
[from-pstn]
include => from-pstn-custom ; create this context in
extensions_custom.conf to include customizations
include => ext-findmefollow ; MODIFICATOIN (PL) for findmefollow if
enabled, should be bofore ext-local
include => ext-did-direct ; MODIFICATOIN (PL) put before ext-did to
take precedence
include => ext-did
exten => fax,1,Goto(ext-fax,in_fax,1)
; MODIFICATION (PL)
;
; Required to assure that direct dids go to personal ring group before
local extension.
; This could be auto-generated however I it is prefered to be put here
and hard coded
; so that it can be modified if ext-local should take precedence in
certain situations.
; will have to decide what to do later.
;
[from-did-direct]
include => ext-findmefollow
include => ext-local
;
############################################################################
; Macros [macro]
;
############################################################################
; Rings one or more extensions. Handles things like call forwarding and DND
; We don't call dial directly for anything internal anymore.
; ARGS: $TIMER, $OPTIONS, $EXT1, $EXT2, $EXT3, ...
; Use a Macro call such as the following:
; Macro(dial,$DIAL_TIMER,$DIAL_OPTIONS,$EXT1,$EXT2,$EXT3,...)
[macro-dial]
exten => s,1,AGI,dialparties.agi
exten => s,2,NoOp(Returned from dialparties with no extensions to call)
exten => s,3,NoOp(DIALSTATUS is '${DIALSTATUS}')
exten => s,10,Dial(${ds}) ; dialparties
will set the priority to 10 if $ds is not null
exten => s,20,NoOp(Returned from dialparties with hunt groups to dial )
exten => s,21,Set(HuntLoop=0)
exten => s,22,GotoIf($[${HuntMembers} >= 1]?30 ) ; if this is from
rg-group, don't strip prefix
exten => s,23,NoOp(Returning there are no members left in the hunt group
to ring)
exten => s,30,Set(HuntMember=HuntMember${HuntLoop})
exten => s,31,GotoIf($[$["${CALLTRACE_HUNT}" != "" ] &
$["${RingGroupMethod}" = "hunt" ]]?32:35 ) ; Set CAll Trace for Hunt
member we are going to call
exten => s,32,Set(CT_EXTEN=${CUT(ARG3,,$[${HuntLoop} + 1])})
exten => s,33,Set(DB(CALLTRACE/${CT_EXTEN})=${CALLTRACE_HUNT})
exten => s,34,Goto(s,42)
exten => s,35,GotoIf($[$["${CALLTRACE_HUNT}" != "" ] &
$["${RingGroupMethod}" = "memoryhunt" ]]?36:50 ) ;Set Call Trace for
each hunt member we are going to call "Memory groups have multiple
members to set CALL TRACE For hence the loop
exten => s,36,Set(CTLoop=0)
exten => s,37,GotoIf($[${CTLoop} > ${HuntLoop}]?42 ) ; if this is from
rg-group, don't strip prefix
exten => s,38,Set(CT_EXTEN=${CUT(ARG3,,$[${CTLoop} + 1])})
exten => s,39,Set(DB(CALLTRACE/${CT_EXTEN})=${CALLTRACE_HUNT})
exten => s,40,Set(CTLoop=$[1 + ${CTLoop}])
exten => s,41,Goto(s,37)
exten => s,42,Dial(${${HuntMember}}${ds} ) ; dialparties will set the
priority to 20 if $ds is not null and its a hunt group
exten => s,43,Set(HuntLoop=$[1 + ${HuntLoop}])
exten => s,44,Set(HuntMembers=$[${HuntMembers} - 1])
exten => s,45,Goto(s,22)
exten => s,50,DBdel(CALLTRACE/${CT_EXTEN})
exten => s,51,Goto(s,42)
; Ring an extension, if the extension is busy or there is no answer send it
; to voicemail
; ARGS: $VMBOX, $EXT
[macro-exten-vm]
exten => s,1,Macro(user-callerid)
exten => s,n,Set(FROMCONTEXT=exten-vm)
exten => s,n,Set(VMBOX=${ARG1})
exten => s,n,Set(EXTTOCALL=${ARG2})
exten => s,n,Set(CFUEXT=${DB(CFU/${EXTTOCALL})})
exten => s,n,Set(RT=${IF($[$["${VMBOX}"!="novm"] |
$["foo${CFUEXT}"!="foo"]]?${RINGTIMER}:"")})
exten => s,n,Macro(record-enable,${EXTTOCALL},IN)
exten => s,n,GotoIf($["${CHANNEL:0:5}" = "Local"]?dolocaldial,1) ; if
the channel is Local
exten => s,n,Macro(dial,${RT},${DIAL_OPTIONS},${EXTTOCALL})
exten => s,n,GosubIf($[$["${DIALSTATUS}"="NOANSWER"] &
$["foo${CFUEXT}"!="foo"]]?docfu,1) ; check for CFU in use on no answer
exten => s,n,NoOp(Voicemail is '${VMBOX}')
exten => s,n,GotoIf($["${VMBOX}" = "novm"]?s-${DIALSTATUS},1) ; no
voicemail in use for this extension
exten => s,n,NoOp(Sending to Voicemail box ${EXTTOCALL})
exten => s,n,Macro(vm,${VMBOX},${DIALSTATUS})
; Local channel should try to ring the phone only then come back out
; i.e. it's wrong for it to Answer the call in any way (including Congestion
; and stop the initiating dialplan from being returned to)
exten => dolocaldial,1,Macro(dial,,${DIAL_OPTIONS},${EXTTOCALL})
exten => dolocaldial,n,NoOp(Returned to dolocaldial with DIALSTATUS
'${DIALSTATUS}')
; Try the Call Forward on No Answer / Unavailable number
exten => docfu,1,Set(RTCFU=${IF($["${VMBOX}"!="novm"]?${RINGTIMER}:"")})
exten =>
docfu,n,Dial(Local/[EMAIL PROTECTED]/n,${RTCFU},${DIAL_OPTIONS})
exten => docfu,n,Return
; Extensions with no Voicemail box reporting BUSY come here
exten => s-BUSY,1,NoOp(Extension is reporting BUSY and not passing to
Voicemail)
exten => s-BUSY,n,Busy()
exten => s-BUSY,n,Wait(60)
exten => s-BUSY,n,Congestion()
; Anything but BUSY comes here
exten => _s-.,1,Congestion()
[macro-vm]
exten => s,1,Macro(user-callerid)
exten => s,n,Set(VMGAIN=${IF($["foo${VM_GAIN}"!="foo"]?"g(${VM_GAIN})":"")})
exten => s,n,Goto(s-${ARG2},1)
exten => s-BUSY,1,NoOp(BUSY voicemail)
exten => s-BUSY,n,Macro(get-vmcontext,${ARG1})
exten => s-BUSY,n,Voicemail([EMAIL PROTECTED]|b${VMGAIN}) ;
Voicemail Busy message
exten => s-BUSY,n,Goto(exit-${VMSTATUS},1)
exten => s-DIRECTDIAL,1,NoOp(DIRECTDIAL voicemail)
exten => s-DIRECTDIAL,n,Macro(get-vmcontext,${ARG1})
exten =>
s-DIRECTDIAL,n,Voicemail([EMAIL PROTECTED]|${VM_DDTYPE}${VMGAIN})
exten => s-DIRECTDIAL,n,Goto(exit-${VMSTATUS},1)
exten => _s-.,1,Macro(get-vmcontext,${ARG1})
exten => _s-.,n,Voicemail([EMAIL PROTECTED]|u${VMGAIN}) ;
Voicemail Unavailable message
exten => _s-.,n,Goto(exit-${VMSTATUS},1)
exten => o,1,Background(one-moment-please) ; 0 during vm message
will hangup
exten => o,n,GotoIf($["foo${FROM_DID}" =
"foo"]?from-pstn,s,1:from-pstn,${FROM_DID},1)
exten => a,1,Macro(get-vmcontext,${ARG1})
exten => a,n,VoiceMailMain([EMAIL PROTECTED])
exten => a,n,Hangup
exten => exit-FAILED,1,Playback(im-sorry&an-error-has-occured)
exten => exit-FAILED,n,Hangup()
exten => exit-SUCCESS,1,Playback(goodbye)
exten => exit-SUCCESS,n,Hangup()
exten => exit-USEREXIT,1,Playback(goodbye)
exten => exit-USEREXIT,n,Hangup()
exten => t,1,Hangup()
; get the voicemail context for the user in ARG1
[macro-get-vmcontext]
exten => s,1,Set(VMCONTEXT=${DB(AMPUSER/${ARG1}/voicemail)})
exten => s,2,GotoIf($["foo${VMCONTEXT}" = "foo"]?200:300)
exten => s,200,Set(VMCONTEXT=default)
exten => s,300,NoOp()
; For some reason, if I don't run setCIDname, CALLERID(name) will be
blank in my AGI
; ARGS: none
[macro-fixcid]
exten => s,1,Set(CALLERID(name)=${CALLERID(name)})
; Ring groups of phones
; ARGS: comma separated extension list
; 1 - Ring Group Strategy
; 2 - ringtimer
; 3 - prefix
; 4 - extension list
[macro-rg-group]
exten => s,1,Macro(user-callerid)
exten => s,2,GotoIf($["${CALLERID(name):0:${LEN(${RGPREFIX})}}" !=
"${RGPREFIX}"]?4:3) ; check for old prefix
exten => s,3,Set(CALLERID(name)=${CALLERID(name):${LEN(${RGPREFIX})}}) ;
strip off old prefix
exten => s,4,Set(RGPREFIX=${ARG3}) ; set new prefix
exten => s,5,Set(CALLERID(name)=${RGPREFIX}${CALLERID(name)}) ; add
prefix to callerid name
exten => s,6,Set(RecordMethod=Group) ; set new prefix
exten => s,7,Macro(record-enable,${MACRO_EXTEN},${RecordMethod})
exten => s,8,Set(RingGroupMethod=${ARG1}) ;
exten => s,9,Macro(dial,${ARG2},${DIAL_OPTIONS},${ARG4})
exten => s,10,Set(RingGroupMethod='') ;
;
; Outgoing channel(s) are busy ... inform the client
;
[macro-outisbusy]
exten => s,1,Playback(all-circuits-busy-now)
exten => s,2,Playback(pls-try-call-later)
exten => s,3,Macro(hangupcall)
; What to do on hangup.
[macro-hangupcall]
exten => s,1,ResetCDR(w)
exten => s,2,NoCDR()
exten => s,3,Wait(5)
exten => s,4,Hangup
[macro-faxreceive]
exten => s,1,Set(FAXFILE=/var/spool/asterisk/fax/${UNIQUEID}.tif)
exten => s,2,Set(EMAILADDR=${FAX_RX_EMAIL})
exten => s,3,rxfax(${FAXFILE})
exten => s,103,Set(EMAILADDR=${FAX_RX_EMAIL})
exten => s,104,Goto(3)
; dialout and strip the prefix
[macro-dialout]
exten => s,1,Macro(user-callerid)
exten => s,2,GotoIf($["${ECID${CALLERID(number)}}" = ""]?5) ;check for
CID override for exten
exten => s,3,Set(CALLERID(all)=${ECID${CALLERID(number)}})
exten => s,4,Goto(7)
exten => s,5,GotoIf($["${OUTCID_${ARG1}}" = ""]?7) ;check for CID
override for trunk
exten => s,6,Set(CALLERID(all)=${OUTCID_${ARG1}})
exten => s,7,Set(length=${LEN(${DIAL_OUT_${ARG1}})})
exten => s,8,Dial(${OUT_${ARG1}}/${ARG2:${length}})
exten => s,9,Congestion
exten => s,109,Macro(outisbusy)
; dialout using default OUT trunk - no prefix
[macro-dialout-default]
exten => s,1,Macro(user-callerid)
exten => s,2,Macro(record-enable,${CALLERID(number)},OUT)
exten => s,3,Macro(outbound-callerid,${ARG1})
exten => s,4,Dial(${OUT}/${ARG1})
exten => s,5,Congestion
exten => s,105,Macro(outisbusy)
; dialout using a trunk, using pattern matching (don't strip any prefix)
; arg1 = trunk number, arg2 = number, arg3 = route password
;
; MODIFIED (PL)
;
; Modified both Dial() commands to include the new TRUNK_OPTIONS from
the general
; screen of AMP
;
[macro-dialout-trunk]
exten => s,1,Set(DIAL_TRUNK=${ARG1})
exten => s,n,Set(DIAL_NUMBER=${ARG2})
exten => s,n,Set(ROUTE_PASSWD=${ARG3})
exten => s,n,GotoIf($["${ROUTE_PASSWD}" = ""]?noauth) ; arg3 is pattern
password
exten => s,n(auth),Authenticate(${ROUTE_PASSWD})
exten => s,n(noauth),Set(GROUP()=OUT_${DIAL_TRUNK})
exten => s,n,Macro(user-callerid)
exten => s,n,Macro(record-enable,${CALLERID(number)},OUT)
exten => s,n,Macro(outbound-callerid,${DIAL_TRUNK})
exten => s,n,GotoIf($["${OUTMAXCHANS_${DIAL_TRUNK}}foo" = "foo"]?nomax)
exten => s,n(checkmax),GotoIf($[ ${GROUP_COUNT()} >
${OUTMAXCHANS_${DIAL_TRUNK}} ]?chanfull)
exten => s,n(nomax),AGI(fixlocalprefix) ; this sets DIAL_NUMBER to the
proper dial string for this trunk
exten => s,n,Set(OUTNUM=${OUTPREFIX_${DIAL_TRUNK}}${DIAL_NUMBER}) ;
OUTNUM is the final dial number
exten => s,n,Set(custom=${CUT(OUT_${DIAL_TRUNK},:,1)}) ; Custom trunks
are prefixed with "AMP:"
exten => s,n,GotoIf($["${custom}" = "AMP"]?customtrunk)
exten => s,n,Dial(${OUT_${DIAL_TRUNK}}/${OUTNUM},120,${TRUNK_OPTIONS}) ;
Regular Trunk Dial
exten => s,n,Goto(s-${DIALSTATUS},1)
exten => s,n(customtrunk),Set(pre_num=${CUT(OUT_${DIAL_TRUNK},$,1)})
exten => s,n,Set(the_num=${CUT(OUT_${DIAL_TRUNK},$,2)}) ; this is where
we expect to find string OUTNUM
exten => s,n,Set(post_num=${CUT(OUT_${DIAL_TRUNK},$,3)})
exten => s,n,GotoIf($["${the_num}" = "OUTNUM"]?outnum:skipoutnum) ; if
we didn't find "OUTNUM", then skip to Dial
exten => s,n(outnum),Set(the_num=${OUTNUM}) ; replace "OUTNUM" with the
actual number to dial
exten =>
s,n(skipoutnum),Dial(${pre_num:4}${the_num}${post_num},120,${TRUNK_OPTIONS})
exten => s,n,Goto(s-${DIALSTATUS},1)
exten => s,n(chanfull),Noop(max channels used up)
exten => s-BUSY,1,NoOp(Trunk is reporting BUSY)
exten => s-BUSY,2,Busy()
exten => s-BUSY,3,Wait(60)
exten => s-BUSY,4,NoOp()
exten => _s-.,1,NoOp(Dial failed due to ${DIALSTATUS})
; Adds a dynamic agent/member to a Queue
; Prompts for call-back number - in not entered, uses CIDNum
[macro-agent-add]
exten => s,1,Wait(1)
exten => s,2,Macro(user-callerid)
exten => s,3,Read(CALLBACKNUM,agent-user) ; get callback number from user
exten => s,4,GotoIf($["${CALLBACKNUM}" = ""]?5:7)) ; if user just
pressed # or timed out, use cidnum
exten => s,5,Set(CALLBACKNUM=${CALLERID(number)})
exten => s,6,GotoIf($["${CALLBACKNUM}" = ""]?2)) ; if still no number,
start over
exten => s,7,GotoIf($["${ARG2}" = ""]?9:8)) ; arg2 is queue password
exten => s,8,Authenticate(${ARG2})
exten =>
s,9,AddQueueMember(${ARG1}|Local/[EMAIL PROTECTED]/n) ; using
chan_local allows us to have agents over trunks
exten => s,10,UserEvent(Agentlogin|Agent: ${CALLBACKNUM})
exten => s,11,Wait(1)
exten => s,12,Playback(agent-loginok)
exten => s,13,Hangup()
; Removes a dynamic agent/member from a Queue
; Prompts for call-back number - in not entered, uses CIDNum
[macro-agent-del]
exten => s,1,Wait(1)
exten => s,2,Macro(user-callerid)
exten => s,3,Read(CALLBACKNUM,agent-user) ; get callback number from user
exten => s,4,GotoIf($["${CALLBACKNUM}" = ""]?5:7)) ; if user just
pressed # or timed out, use cidnum
exten => s,5,Set(CALLBACKNUM=${CALLERID(number)})
exten => s,6,GotoIf($["${CALLBACKNUM}" = ""]?2)) ; if still no number,
start over
exten => s,7,RemoveQueueMember(${ARG1}|Local/[EMAIL PROTECTED]/n)
exten => s,8,UserEvent(RefreshQueue)
exten => s,9,Wait(1)
exten => s,10,Playback(agent-loggedoff)
exten => s,11,Hangup()
; arg1 = trunk number, arg2 = number
[macro-dialout-enum]
; This has been violently beaten upon by Rob Thomas, [EMAIL PROTECTED]
; to 1: Be compliant with all the depreciated bits in asterisk 1.2 and
; above, and 2: to give a good shot at attempting to be compliant with
; RFC3761 by honouring the order in which records are returned.
exten => s,1,GotoIf($["${ARG3}" = ""]PASSWD?NOPASSWD); arg3 is pattern
password
exten => s,n(PASSWD),Authenticate(${ARG3})
exten => s,n(NOPASSWD),Macro(user-callerid)
exten => s,n,Macro(record-enable,${CALLERID(number)},OUT)
exten => s,n,Macro(outbound-callerid,${ARG1})
exten => s,n,Set(GROUP()=OUT_${ARG1})
exten => s,n,GotoIf($[ ${GROUP_COUNT()} > ${OUTMAXCHANS_${ARG1}} ]?nochans)
exten => s,n,Set(DIAL_NUMBER=${ARG2})
exten => s,n,Set(DIAL_TRUNK=${ARG1})
exten => s,n,AGI(fixlocalprefix) ; this sets DIAL_NUMBER to the proper
dial string for this trunk
exten => s,n,Set(E164NETWORKS=e164.arpa-e164.info-e164.org) ; enum
networks to check
exten => s,n,GotoIf($["${DIAL_NUMBER:0:1}" = "+"]?begin) ; Skip next
line if it already is prefixed by a plus
exten => s,n,Set(DIAL_NUMBER=+${DIAL_NUMBER}) ; Add a plus to the start,
becasue ENUMLOOKUP needs it.
; start of main network loop
exten => s,n(begin),NoOp(E164NETWORKS is ${E164NETWORKS})
exten => s,n,GotoIf($["${E164NETWORKS:1:2}"=""]?failedtotally)
exten => s,n,Set(ENUMNET=${CUT(E164NETWORKS,-,1)})
exten => s,n,Set(E164NETWORKS=${CUT(E164NETWORKS,-,2-)})
exten => s,n,NoOp(E164NETWORKS is now ${E164NETWORKS})
exten => s,n,NoOp(ENUMNET is ${ENUMNET})
exten => s,n,Set(ENUMCOUNT=${ENUMLOOKUP(${DIAL_NUMBER},all,c,${ENUMNET})})
exten => s,n,Set(ENUMPTR=0)
exten => s,n,Set(LOOKUPBUG=0)
; start of main lookup loop
exten =>
s,n(startloop),GotoIf($["${ENUMPTR}"<"${ENUMCOUNT}"]?continue:failed)
; Now, let's start through them.
exten => s,n(continue),Set(ENUMPTR=$[${ENUMPTR}+1])
exten => s,n,NoOp(Doing
ENUMLOOKUP(${DIAL_NUMBER},all,${ENUMPTR},${ENUMNET}))
exten =>
s,n,Set(ENUM=${ENUMLOOKUP(${DIAL_NUMBER},all,${ENUMPTR},${ENUMNET})})
; Deal with reponse
exten => s,n,GotoIf($["${ENUM:0:3}" = "sip" ]?sipuri)
exten => s,n,GotoIf($["${ENUM:0:3}" = "iax" ]?iaxuri)
; It doesn't matter if you don't have h323 enabled, as when it tries to
dial, it cares
; about dialstatus and retries if there are any enum results left.
exten => s,n,GotoIf($["${ENUM:0:3}" = "h32" ]?h323uri)
; e164.org can return 'ADDRESS' lines. Because of *'s poor handling of Enum
; lookups, we want to DECREMENT the enum pointer. Yes. That means we try
more
; times than there actually exists entries.
exten => s,n,GotoIf($["${ENUM:0:3}" = "ADD" ]?enumbug)
; OK. If we're here, we've still got some enum entries to go through.
Back to
; the start with you!
exten => s,n,Goto(startloop)
; We're here because of the poor implementation of ENUMLOOKUP in
Asterisk. It
; is quite possible to do three ENUMLOOKUPS and get the same entry each
time.
; The only workaround I can think of is when we hit an invalid entry, do a
; DECREMENT of the pointer, and keep trying.
exten => s,n(enumbug),Set(ENUMPTR=$[${ENUMPTR}-1])
exten => s,n,NoOp(If this is looping with the same ENUM value, The
ENUMLOOKUP function is fixed!)
exten => s,n,Set(LOOKUPBUG=$[${LOOKUPBUG}+1])
; If we've done this more than, ooh, 5 times, then give up on this
network. Sorry.
exten => s,n,GotoIf($["${LOOKUPBUG}" > 5 ]?failed)
exten => s,n,Goto(continue)
; If the prefix is 'sip:'...
exten => s,n(sipuri),Set(DIALSTR=SIP/${ENUM:4})
exten => s,n,Goto(dodial)
; If it's IAX2...
exten => s,n(iaxuri),Set(DIALSTR=IAX2/${ENUM:5})
exten => s,n,Goto(dodial)
; Or even if it's H323.
exten => s,n(h323uri),Set(DIALSTR=H323/${ENUM:5})
exten => s,n(dodial),Dial(${DIALSTR})
exten => s,n,NoOp(Dial exited in macro-enum-dialout with ${DIALSTATUS})
; Now, if we're still here, that means the Dial failed for some reason.
; If it's CONGESTION or CHANUNAVAIL we probably want to try again on a
; different channel. However, if it's the last one, we don't have any
; left, and I didn't keep any previous dialstatuses, so hopefully
; someone looking throught the logs would have seen the NoOp's
exten => s,n,GotoIf($["${ENUMPTR}"<"${ENUMCOUNT}"]?maybemore:dialfailed)
exten => s,n(maybemore),GotoIf($[ $[ "${DIALSTATUS}" = "CHANUNAVAIL" ] |
$[ "${DIALSTATUS}" = "CONGESTION" ] ]?continue)
; If we're here, then it's BUSY or NOANSWER or something and well, deal
with it.
exten => s,n(dialfailed),Goto(s-${DIALSTATUS},1)
; Here are the exit points for the macro.
exten => s,n(failed),NoOp(EnumLookup failed on network ${ENUMNET})
exten => s,n,Goto(begin)
exten => s,n(failedtotally),NoOp(EnumLookup failed -- no more networks
to try)
exten => s,n,Goto(end)
exten => s,n(nochans),NoOp(max channels used up)
exten => s,n(end),NoOp(Exiting macro-dialout-enum)
exten => s-BUSY,1,NoOp(Trunk is reporting BUSY)
exten => s-BUSY,2,Busy()
exten => s-BUSY,3,Wait(60)
exten => s-BUSY,4,NoOp()
exten => _s-.,1,NoOp(Dial failed due to ${DIALSTATUS})
[macro-record-enable]
exten => s,1,GotoIf(${LEN(${BLINDTRANSFER})} > 0?2:4)
exten => s,2,ResetCDR(w)
exten => s,3,StopMonitor()
exten => s,4,AGI(recordingcheck,${TIMESTAMP},${UNIQUEID})
exten => s,5,Noop(No recording needed)
exten => s,999,Monitor(wav49,${CALLFILENAME}, mb)
;exten => s,3,BackGround(for-quality-purposes)
;exten => s,4,BackGround(this-call-may-be)
;exten => s,5,BackGround(recorded)
; This macro is for dev purposes and just dumps channel/app variables.
Useful when designing new contexts.
[macro-dumpvars]
exten => s,1,Noop(ACCOUNTCODE=${ACCOUNTCODE})
exten => s,2,Noop(ANSWEREDTIME=${ANSWEREDTIME})
exten => s,3,Noop(BLINDTRANSFER=${BLINDTRANSFER})
exten => s,4,Noop(CALLERID=${CALLERID(all)})
exten => s,5,Noop(CALLERID(name)=${CALLERID(name)})
exten => s,6,Noop(CALLERID(number)=${CALLERID(number)})
exten => s,7,Noop(CALLINGPRES=${CALLINGPRES})
exten => s,8,Noop(CHANNEL=${CHANNEL})
exten => s,9,Noop(CONTEXT=${CONTEXT})
exten => s,10,Noop(DATETIME=${DATETIME})
exten => s,11,Noop(DIALEDPEERNAME=${DIALEDPEERNAME})
exten => s,12,Noop(DIALEDPEERNUMBER=${DIALEDPEERNUMBER})
exten => s,13,Noop(DIALEDTIME=${DIALEDTIME})
exten => s,14,Noop(DIALSTATUS=${DIALSTATUS})
exten => s,15,Noop(DNID=${DNID})
exten => s,16,Noop(EPOCH=${EPOCH})
exten => s,17,Noop(EXTEN=${EXTEN})
exten => s,18,Noop(HANGUPCAUSE=${HANGUPCAUSE})
exten => s,19,Noop(INVALID_EXTEN=${INVALID_EXTEN})
exten => s,20,Noop(LANGUAGE=${LANGUAGE})
exten => s,21,Noop(MEETMESECS=${MEETMESECS})
exten => s,22,Noop(PRIORITY=${PRIORITY})
exten => s,23,Noop(RDNIS=${RDNIS})
exten => s,24,Noop(SIPDOMAIN=${SIPDOMAIN})
exten => s,25,Noop(SIP_CODEC=${SIP_CODEC})
exten => s,26,Noop(SIPCALLID=${SIPCALLID})
exten => s,27,Noop(SIPUSERAGENT=${SIPUSERAGENT})
exten => s,28,Noop(TIMESTAMP=${TIMESTAMP})
exten => s,29,Noop(TXTCIDNAME=${TXTCIDNAME})
exten => s,30,Noop(UNIQUEID=${UNIQUEID})
exten => s,31,Noop(TOUCH_MONITOR=${TOUCH_MONITOR})
exten => s,32,Noop(MACRO_CONTEXT=${MACRO_CONTEXT})
exten => s,33,Noop(MACRO_EXTEN=${MACRO_EXTEN})
exten => s,34,Noop(MACRO_PRIORITY=${MACRO_PRIORITY})
[macro-user-logon]
; check device type
exten => s,1,Set(DEVICETYPE=${DB(DEVICE/${CALLERID(number)}/type)})
exten => s,2,GotoIf($["${DEVICETYPE}" = "fixed"]?s-FIXED,1)
; get user's extension
exten => s,3,Set(AMPUSER=${ARG1})
exten => s,4,GotoIf($["${AMPUSER}" = ""]?5:9)
exten => s,5,BackGround(please-enter-your)
exten => s,6,Playback(extension)
exten => s,7,Read(AMPUSER,then-press-pound)
; get user's password and authenticate
exten => s,8,Wait(1)
exten => s,9,Set(AMPUSERPASS=${DB(AMPUSER/${AMPUSER}/password)})
exten => s,10,GotoIf($[${LEN(${AMPUSERPASS})} = 0]?s-NOPASSWORD,1)
; do not continue if the user has already logged onto this device
exten => s,11,Set(DEVICEUSER=${DB(DEVICE/${CALLERID(number)}/user)})
exten => s,12,GotoIf($["${DEVICEUSER}" = "${AMPUSER}"]?s-ALREADYLOGGEDON,1)
exten => s,13,Authenticate(${AMPUSERPASS})
; devices can only be mapped to one user - loggoff anyone else who is here
exten => s,14,Macro(user-logoff)
; map user to device
exten => s,15,Set(AMPUSERDEVICES=${DB(AMPUSER/${AMPUSER}/device)})
exten => s,16,GotoIf($[${LEN(${AMPUSERDEVICES})} = 0]?18)
exten => s,17,Set(AMPUSERDEVICES=${AMPUSERDEVICES}&)
exten => s,18,Set(AMPUSERDEVICES=${AMPUSERDEVICES}${CALLERID(number)})
exten => s,19,Set(DB(AMPUSER/${AMPUSER}/device)=${AMPUSERDEVICES})
; map device to user
exten => s,20,Set(DB(DEVICE/${CALLERID(number)}/user)=${AMPUSER})
; create symlink from dummy device mailbox to user's mailbox
exten => s,21,System(/bin/ln -s
/var/spool/asterisk/voicemail/default/${AMPUSER}/
/var/spool/asterisk/voicemail/device/${CALLERID(number)})
exten => s-FIXED,1,NoOp(Device is FIXED and cannot be logged into)
exten => s-FIXED,2,Playback(ha/phone)
exten => s-FIXED,3,SayDigits(${CALLERID(number)})
exten => s-FIXED,4,Playback(is-curntly-unavail)
exten => s-FIXED,5,Playback(vm-goodbye)
exten => s-FIXED,6,Hangup ;TODO should play msg indicated device cannot
be logged into
exten => s-ALREADYLOGGEDON,1,NoOp(This device has already been logged
into by this user)
exten => s-ALREADYLOGGEDON,2,Playback(vm-goodbye)
exten => s-ALREADYLOGGEDON,3,Hangup ;TODO should play msg indicated
device is already logged into
exten => s-NOPASSWORD,1,NoOp(This extension does not exist or no
password is set)
exten => s-NOPASSWORD,2,Playback(an-error-has-occured)
exten => s-NOPASSWORD,3,Playback(vm-goodbye)
exten => s-NOPASSWORD,4,Hangup ;TODO should play msg indicated device is
already logged into
[macro-user-logoff]
; check device type
exten => s,1,Set(DEVICETYPE=${DB(DEVICE/${CALLERID(number)}/type)})
exten => s,2,GotoIf($["${DEVICETYPE}" = "fixed"]?s-FIXED,1)
; remove entry from user's DEVICE key
; delete the symlink to user's voicemail box
exten => s,3,System(rm -f
/var/spool/asterisk/voicemail/device/${CALLERID(number)})
exten => s,4,Set(DEVAMPUSER=${DB(DEVICE/${CALLERID(number)}/user)})
exten => s,5,Set(AMPUSERDEVICES=${DB(AMPUSER/${DEVAMPUSER}/device)})
exten =>
s,6,AGI(list-item-remove.php,${AMPUSERDEVICES},${CALLERID(number)},AMPUSERDEVICES,&)
; reset user -> device mapping
; users can log onto multiple devices, need to just remove device from value
exten => s,7,Set(DB(AMPUSER/${DEVAMPUSER}/device)=${AMPUSERDEVICES})
; reset device -> user mapping
exten => s,8,Set(DB(DEVICE/${CALLERID(number)}/user)=none)
exten => s,9,Playback(vm-goodbye)
exten => s-FIXED,1,NoOp(Device is FIXED and cannot be logged out of)
exten => s-FIXED,2,Playback(an-error-has-occured)
exten => s-FIXED,3,Playback(vm-goodbye)
exten => s-FIXED,4,Hangup ;TODO should play msg indicated device cannot
be logged into
[macro-systemrecording]
exten => s,1,Goto(${ARG1},1)
exten => dorecord,1,Record(/tmp/${CALLERID(number)}-ivrrecording:wav)
exten => dorecord,n,Wait(1)
exten => dorecord,n,Goto(confmenu,1)
exten => docheck,1,Playback(/tmp/${CALLERID(number)}-ivrrecording)
exten => docheck,n,Wait(1)
exten => docheck,n,Goto(confmenu,1)
exten =>
confmenu,1,Background(to-listen-to-it&press-1&to-rerecord-it&press-star|m||macro-systemrecording)
exten => confmenu,n,Read(RECRESULT||1|||4)
exten => confmenu,n,GotoIf($["x${RECRESULT}"="x*"]?dorecord,1)
exten => confmenu,n,GotoIf($["x${RECRESULT}"="x1"]?docheck,1)
exten => confmenu,n,Goto(1)
exten => 1,1,Goto(docheck,1)
exten => *,1,Goto(dorecord,1)
exten => t,1,Playback(goodbye)
exten => t,n,Hangup
exten => i,1,Playback(pm-invalid-option)
exten => i,n,Goto(confmenu,1)
exten => h,1,Hangup
;
;
############################################################################
; CallerID Handling
;
############################################################################
;sets the callerid of the device to that of the logged in user
[macro-user-callerid]
exten => s,1,GotoIf($["${CHANNEL:0:5}" = "Local"]?report)
exten => s,n,GotoIf($["${REALCALLERIDNUM:1:2}" != ""]?start)
exten => s,n,Set(REALCALLERIDNUM=${CALLERID(number)})
exten => s,n(start),NoOp(REALCALLERIDNUM is ${REALCALLERIDNUM})
exten => s,n,Set(AMPUSER=${DB(DEVICE/${REALCALLERIDNUM}/user)})
exten => s,n,Set(AMPUSERCIDNAME=${DB(AMPUSER/${AMPUSER}/cidname)})
exten => s,n,GotoIf($["x${AMPUSERCIDNAME:1:2}" = "x"]?report)
exten => s,n,Set(CALLERID(all)=${AMPUSERCIDNAME} <${AMPUSER}>)
exten => s,n(report),NoOp(Using CallerID ${CALLERID(all)})
; overrides callerid out trunks
; arg1 is trunk
; macro-user-callerid should be called _before_ using this macro
[macro-outbound-callerid]
exten => s,1,GotoIf($["${REALCALLERIDNUM:1:2}" != ""]?start)
exten => s,n,Set(REALCALLERIDNUM=${CALLERID(number)})
exten => s,n(start),NoOp(REALCALLERIDNUM is ${REALCALLERIDNUM})
exten => s,n,Set(USEROUTCID=${DB(AMPUSER/${REALCALLERIDNUM}/outboundcid)})
exten =>
s,n,Set(EMERGENCYCID=${DB(DEVICE/${REALCALLERIDNUM}/emergency_cid)})
exten => s,n,Set(TRUNKOUTCID=${OUTCID_${ARG1}})
exten => s,n,GotoIf($["${EMERGENCYROUTE:1:2}" = ""]?trunkcid) ; check
EMERGENCY ROUTE
exten => s,n,GotoIf($["${EMERGENCYCID:1:2}" = ""]?trunkcid) ; empty
EMERGENCY CID, so default back to trunk
exten => s,n,Set(CALLERID(all)=${EMERGENCYCID}) ; emergency cid for device
exten => s,n,Goto(report)
exten => s,n(trunkcid),GotoIf($["${TRUNKOUTCID:1:2}" = ""]?usercid)
;check for CID override for trunk (global var)
exten => s,n,Set(CALLERID(all)=${TRUNKOUTCID})
exten => s,n(usercid),GotoIf($["${USEROUTCID:1:2}" = ""]?report) ; check
CID override for extension
exten => s,n,Set(CALLERID(all)=${USEROUTCID})
exten => s,n(report),NoOp(CallerID set to ${CALLERID(all)})
; Privacy Manager Macro makes sure that any calls that don't pass the
privacy manager are presented
; with congestion since there have been observed cases of the call
continuing if not stopped with a
; congestion, and this provides a slightly more friendly 'sorry' message
in case the user is
; legitamately trying to be cooperative.
;
; Note: the following options are configurable in privacy.conf:
;
; maxretries = 3 ; default value, number of retries before failing
; minlength = 10 ; default value, number of digits to be accepted as
valid CID
;
[macro-privacy-mgr]
exten => s,1,Set(KEEPCID=${CALLERID(num)})
exten => s,n,GotoIf($["foo${CALLERID(num):0:1}"="foo+"]?CIDTEST2:CIDTEST1)
exten => s,n(CIDTEST1),Set(TESTCID=${MATH(1+${CALLERID(num)})})
exten => s,n,Goto(TESTRESULT)
exten => s,n(CIDTEST2),Set(TESTCID=${MATH(1+${CALLERID(num):1})})
exten => s,n(TESTRESULT),GotoIf($["foo${TESTCID}"="foo"]?CLEARCID:PRIVMGR)
exten => s,n(CLEARCID),Set(CALLERID(num)=)
exten => s,n(PRIVMGR),PrivacyManager()
exten => s,n,SetCallerPres(allowed_passed_screen); stop gap until
app_privacy.c clears unavailble bit
exten => s,PRIVMGR+101,Noop(STATUS: ${PRIVACYMGRSTATUS} CID:
${CALLERID(num)} ${CALLERID(name)} CALLPRES: ${CALLLINGPRES})
exten => s,n,Playback(sorry-youre-having-problems)
exten => s,n,Playback(goodbye)
exten => s,n,Congestion()
exten => s,n,Hangup
;
;
############################################################################
; Inbound Contexts [from]
;
############################################################################
[from-sip-external]
;give external sip users congestion and hangup
; Yes. This is _really_ meant to be _. - I know asterisk whinges about
it, but
; I do know what I'm doing. This is correct.
exten => _.,1,NoOp(Received incoming SIP connection from unknown peer to
${EXTEN})
exten => _.,n,Set(DID=${IF($["${EXTEN:1:2}"=""]?s:${EXTEN})})
exten => _.,n,Goto(s,1)
exten => s,1,GotoIf($["${ALLOW_SIP_ANON}"="yes"]?from-trunk,${DID},1)
exten => s,n,Set(TIMEOUT(absolute)=15)
exten => s,n,Answer
exten => s,n,Wait(2)
exten => s,n,Playback(ss-noservice)
exten => s,n,Congestion
exten => s,n,Hangup
exten => h,1,NoOp(Hangup)
exten => i,1,NoOp(Invalid)
exten => t,1,NoOp(Timeout)
[from-internal]
; applications are now mostly all found in from-internal-additional in
_custom.conf
include => parkedcalls
include => from-internal-custom
;allow phones to dial other extensions
include => ext-fax
;allow phones to access generated contexts
;
; MODIFIED (PL)
;
; Currently the include for findmefollow is being auto-generated before
ext-local which is the desired behavior.
; However, I haven't been able to do anything that I know of to force
this. We need to determine if it should
; be hardcoded into here to make sure it doesn't change with some
configuration. For now I will leave it out
; until we can discuss this.
;
include => from-internal-additional
exten => s,1,Macro(hangupcall)
exten => h,1,Macro(hangupcall)
[from-zaptel]
exten => _X.,1,Set(DID=${EXTEN})
exten => _X.,n,Goto(s,1)
exten => s,1,NoOp(Entering from-zaptel with DID == ${DID})
; If ($did == "") { $did = "s"; }
exten => s,n,Set(DID=${IF($["${DID}"= ""]?s:${DID})})
exten => s,n,NoOp(DID is now ${DID})
exten => s,n,GotoIf($["${CHANNEL:0:3}"="Zap"]?zapok:notzap)
exten => s,n(notzap),Goto(ext-did,${DID},1)
; If there's no ext-did,s,1, that means there's not a no did/no cid
route. Hangup.
exten => s,n,Macro(hangup)
exten => s,n(zapok),NoOp(Is a Zaptel Channel)
exten => s,n,Set(CHAN=${CHANNEL:4})
exten => s,n,Set(CHAN=${CUT(CHAN,-,1)})
exten => s,n,Macro(from-zaptel-${CHAN},${DID},1)
; If nothing there, then treat it as a DID
exten => s,n,NoOp(Returned from Macro from-zaptel-${CHAN})
exten => s,n,Goto(ext-did,${DID},1)
;
############################################################################
; Extension Contexts [ext]
;
############################################################################
[ext-fax]
exten => s,1,Answer
exten => s,2,Goto(in_fax,1)
exten => in_fax,1,StopPlayTones
exten => in_fax,2,GotoIf($["${FAX_RX}" = "system"]?3:analog_fax,1)
exten => in_fax,3,Macro(faxreceive)
exten => in_fax,4,system(/var/lib/asterisk/bin/fax-process.pl --to
${EMAILADDR} --from ${FAX_RX_FROM} --subject "Fax from
${CALLERID(number)} ${CALLERID(name)}" --attachment
${CALLERID(number)}.pdf --type application/pdf --file ${FAXFILE});
exten => in_fax,5,Hangup
exten => analog_fax,1,GotoIf($["${FAX_RX}" = "disabled"]?4:2) ;if fax
is disabled, just hang up
exten => analog_fax,2,Set(DIAL=${DB(DEVICE/${FAX_RX}/dial)});
exten => analog_fax,3,Dial(${DIAL},20,d)
exten => analog_fax,4,Hangup
;exten => out_fax,1,wait(7)
exten => out_fax,1,txfax(${TXFAX_NAME}|caller)
exten => out_fax,2,Hangup
exten => h,1,Hangup()
;this is where parked calls go if they time-out. Should probably re-ring
[default]
include => ext-local
exten => s,1,Playback(vm-goodbye)
exten => s,2,Macro(hangupcall)
_______________________________________________
--Bandwidth and Colocation provided by Easynews.com --
Asterisk-Users mailing list
To UNSUBSCRIBE or update options visit:
http://lists.digium.com/mailman/listinfo/asterisk-users