Are you sure the other end is configured properly?
What does "zttool" says?
Have you turned on all the asterisk debug messages to look further?
Regards
On 7/19/06, Lincoln Zuljewic Silva <[EMAIL PROTECTED]> wrote:
Hello all. I have a Digitum TE110P board configured and working (I think
that it's working). When I configure in extensions.conf to a extension route
to that board I get "Unable to create channel of type 'Zap'" on log.
Here are some configuration:
lspci -vv
0000:01:07.0 Network controller: Tiger Jet Network Inc. Tiger3XX Modem/ISDN
interface
Subsystem: Unknown device 795e:0001
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (250ns min, 32000ns max)
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at c800 [size=256]
Region 1: Memory at fc5ff000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI+ D1- D2+ AuxCurrent=0mA
PME(D0+,D1-,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
ztcfg -vv
Zaptel Configuration
======================
SPAN 1: CAS/HDB3 Build-out: 0 db (CSU)/0-133 feet (DSX-1)
Channel map:
Channel 01: Individual Clear channel (Default) (Slaves: 01)
Channel 02: Individual Clear channel (Default) (Slaves: 02)
Channel 03: Individual Clear channel (Default) (Slaves: 03)
Channel 04: Individual Clear channel (Default) (Slaves: 04)
Channel 05: Individual Clear channel (Default) (Slaves: 05)
Channel 06: Individual Clear channel (Default) (Slaves: 06)
Channel 07: Individual Clear channel (Default) (Slaves: 07)
Channel 08: Individual Clear channel (Default) (Slaves: 08)
Channel 09: Individual Clear channel (Default) (Slaves: 09)
Channel 10: Individual Clear channel (Default) (Slaves: 10)
Channel 11: Individual Clear channel (Default) (Slaves: 11)
Channel 12: Individual Clear channel (Default) (Slaves: 12)
Channel 13: Individual Clear channel (Default) (Slaves: 13)
Channel 14: Individual Clear channel (Default) (Slaves: 14)
Channel 15: Individual Clear channel (Default) (Slaves: 15)
Channel 16: D-channel (Default) (Slaves: 16)
Channel 17: Individual Clear channel (Default) (Slaves: 17)
Channel 18: Individual Clear channel (Default) (Slaves: 18)
Channel 19: Individual Clear channel (Default) (Slaves: 19)
Channel 20: Individual Clear channel (Default) (Slaves: 20)
Channel 21: Individual Clear channel (Default) (Slaves: 21)
Channel 22: Individual Clear channel (Default) (Slaves: 22)
Channel 23: Individual Clear channel (Default) (Slaves: 23)
Channel 24: Individual Clear channel (Default) (Slaves: 24)
Channel 25: Individual Clear channel (Default) (Slaves: 25)
Channel 26: Individual Clear channel (Default) (Slaves: 26)
Channel 27: Individual Clear channel (Default) (Slaves: 27)
Channel 28: Individual Clear channel (Default) (Slaves: 28)
Channel 29: Individual Clear channel (Default) (Slaves: 29)
Channel 30: Individual Clear channel (Default) (Slaves: 30)
Channel 31: Individual Clear channel (Default) (Slaves: 31)
31 channels configured.
My zaptel.cfg
span=1,0,0,cas,hdb3
loadzone=us
defaultzone=us
bchan=1-15,17-31
dchan=16
My zapata.conf
[channels]
context=customer
signalling=pri_cpe
channel => 1
My extensions.conf
exten => 4502,1,Dial(Zap/1/4502)
show channels in Asterisk CLI:
Channel (Context Extension Pri ) State Appl. Data
0 active channel(s)
zap show channels in Asterisk CLI:
Chan Extension Context Language MusicOnHold
pseudo customer
1 customer
zap show channel 1 in Asterisk CLI:
hannel: 1>
File Descriptor: 10
Span: 1
Extension:
Dialing: no
Context: corsidian
Caller ID string:
Destroy: 0
InAlarm: 0
Signalling Type: PRI Signalling
Owner: <None>
Real: <None>
Callwait: <None>
Threeway: <None>
Confno: -1
Propagated Conference: -1
Real in conference: 0
DSP: no
Relax DTMF: no
Dialing/CallwaitCAS: 0/0
Default law: alaw
Fax Handled: no
Pulse phone: no
Echo Cancellation: 0 taps unless TDM bridged, currently OFF
PRI Flags:
PRI Logical Span: Implicit
Actual Hookstate: Onhook
When I dial 4502 in the softphone I get "Unable to create channel of type
'Zap'".
Could anybody give to me a little help ?
Thanks a lot !
Lincoln
_______________________________________________
--Bandwidth and Colocation provided by Easynews.com --
asterisk-users mailing list
To UNSUBSCRIBE or update options visit:
http://lists.digium.com/mailman/listinfo/asterisk-users
--
"Su nombre es GNU/Linux, no solamente Linux, mas info en http://www.gnu.org";
_______________________________________________
--Bandwidth and Colocation provided by Easynews.com --
asterisk-users mailing list
To UNSUBSCRIBE or update options visit:
http://lists.digium.com/mailman/listinfo/asterisk-users
