This is the scenarios: 1 - ### /etc/zaptel.conf span=1,1,0,ccs,hdb3,crc4 bchan=5-19,21-35 dchan=20 fxsks=1-4 loadzone = us defaultzone=us ### modprobe wcte11xp ZT_CHANCONFIG failed on channel 32: No such device or address (6) FATAL: Error running install command for wcte11xp
2 - ### /etc/zaptel.conf span=1,1,0,ccs,hdb3,crc4 bchan=5-19,21-35 dchan=20 fxsks=1-4 loadzone = us defaultzone=us ### modprobe wctdm ZT_CHANCONFIG failed on channel 5: No such device or address (6) FATAL: Error running install command for wctdm 3 - ### /etc/zaptel.conf span=1,1,0,ccs,hdb3,crc4 bchan=1-15,17-31 dchan=16 fxsks=32-35 loadzone = us defaultzone=us ### modprobe wcte11xp....ok modprobe wctdm....ok modprobe wcfxo....ok modprobe wct4xxp....ok modprobe zaptel....ok ### /etc/asterisk/zapata.conf [channels] context=corsidian overlapdial=yes immediate=no callprogress=yes busydetect=no switchtype=euroisdn signalling=pri_net channel => 1-15,17-31 group=2 group=1 callgroup=1 pickupgroup=1 signalling=fxs_ks channel => 32-35 ### tail -f /var/log/asterisk/messages Nov 22 15:11:43 ERROR[5524] chan_zap.c: Channel 16 is reserved for D-channel. Nov 22 15:11:43 ERROR[5524] chan_zap.c: Unable to register channel '1-15' Nov 22 15:11:43 WARNING[5524] loader.c: chan_zap.so: load_module failed, returning -1 Nov 22 15:11:43 WARNING[5524] loader.c: Loading module chan_zap.so failed! ----- Original Message ----- From: Henk Dick To: 'Lincoln Zuljewic Silva' ; 'Asterisk Users Mailing List - Non-Commercial Discussion' Sent: Wednesday, November 22, 2006 4:08 PM Subject: RE: [asterisk-users] TE110P and TDM400P I think that you are loading the drivers in the wrong order. You can change the order of loading are first define the E1 followed by the TDM400 Hope this helps, Henk ------------------------------------------------------------------------------ From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Lincoln Zuljewic Silva Sent: woensdag 22 november 2006 20:51 To: asterisk-users@lists.digium.com Subject: [asterisk-users] TE110P and TDM400P Hello all. I have here a TE110P (configured as E1) and a TDM400P (with four X100P - FXS). Both boards are recognized by the operating system as showed above: 0000:08:00.0 Communication controller: Tiger Jet Network Inc. Tiger3XX Modem/ISDN interface Subsystem: Unknown device b1d9:0003 Flags: bus master, medium devsel, latency 64, IRQ 169 I/O ports at e800 [size=256] Memory at febff000 (32-bit, non-prefetchable) [size=4K] Capabilities: [40] Power Management version 2 0000:08:01.0 Network controller: Tiger Jet Network Inc. Tiger3XX Modem/ISDN interface Subsystem: Unknown device 79fe:0001 Flags: bus master, medium devsel, latency 64, IRQ 193 I/O ports at e400 [size=256] Memory at febfe000 (32-bit, non-prefetchable) [size=4K] Capabilities: [40] Power Management version 2 The problem is that I cant make the both cards to work together in the same server. Here is my /etc/zaptel.conf: ### fxsks=1-4 loadzone = us defaultzone=us span=1,1,0,ccs,hdb3,crc4 bchan=5-19,21-35 dchan=20 ### When I load the wctdm module, I get this error: ZT_CHANCONFIG failed on channel 5: No such device or address (6). Its sounds like the FXS module its tring to configure the channels 5 to 35 (E1 - ISDN Channels - TE110P card). Anybody already saw this ? Its possible to use this two cards in the same computer ? There is any separator that I can use in zaptel.conf to make the load of the modules dont mistakes itself ? Here is my versions: Debian kernel - 2.6.8 asterisk-1.2.12.1 libpri-1.2.4 zaptel-1.2.11 Thanks Lincoln
_______________________________________________ --Bandwidth and Colocation provided by Easynews.com -- asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
