I purchased FXS modules so that I could terminate the machines or faxes (eg just like a standard phone) the outgoing/incoming channel will be be provided by my E1.
I hope I have the right modules for the job? ----- Original Message ----- From: "Tzafrir Cohen" <[EMAIL PROTECTED]> To: <asterisk-users@lists.digium.com> Sent: Thursday, June 14, 2007 11:22 AM Subject: Re: [asterisk-users] TDM400p and te110p configuration. > On Thu, Jun 14, 2007 at 09:45:01AM +0100, Matt Scott wrote: > > Dear users. > > > > My current setup uses a euroISDN E1 with 8 cahnnels for incoming and > > outgoing calls from a digium te110p. Currently all phones use SIP. > > > > However, I need to add some faxes lines and some POS credit card > > machines. These will require POTS lines with a fixed DDI. > > I have purchased the tdm400p and 4 FXS modules. > > *FXO* modules, right? > > > > > My problem is with the zaptel.conf and zapata.conf. > > I am a little confused as how to separate the specific requirements for > > each card. > > > > How do I create a span for the tdm400p? > > You don't . Just 'fxsks' lines which look like bchan/dchan lines in > zaptel.conf. In zapata.conf they are the same channels (with fxs_ks > signalling). > > > I would imagine they require their own context and specific group? > > Right. > > > Also the channel numbers become a bit of a problem. Do they become > > sequential carrying on from each card???? > > cat /proc/zaptel/* > > > I would imagine I need to modprobe the correct drivers for this card > > as well. Will there be any conflict? > > What type of conflict? The number of a channel is set when you load a > driver (technically: when you register its spans to zaptel). > > If you want to make sure that the current channels of the E1 card keep > their numbers, you should load the analog card second. On Debian systems > you can guarantee that by e.g. putting the module names in the proper > order in /etc/modules . > > > > > Here is my current zaptel and zapata confs with the te110p requirements ONLY. > > > > zaptel: > > loadzone = uk > > defaultzone = uk > > span = 1,0,0,ccs,hdb3,crc4 > > bchan = 1-15,17-31 > > dchan = 16 > > # Something of the sort of: > fxsks = 32-35 > > > > > > > > zapata: > > [channels] > > language=en > > usecallerid=yes > > hidecallerid=no > > callwaiting=no > > callwaitingcallerid=yes > > restrictcid=no > > usecallingpres=no > > threewaycalling=yes > > callreturn=yes > > transfer=yes > > cancallforward=yes > > echocancelwhenbridged=yes > > echocancel=yes > > musiconhold=default > > rxgain=0.0 > > txgain=0.0 > > signalling=pri_cpe > > switchtype=euroisdn > > immediate=no > > overlapdial=yes > > pridialplan=unknown > > prilocaldialplan=unknown > > > > group=1 > > context = from-pstn > > callerid=asreceived > > channel => 1-8 > > ; something of the sort of: > ; context = from-pots > ; group = 2 > cidsignalling = v23 > cidstart = polarity > channel => 32-35 > > Alternatively use genzaptelconf, but be sure to set lc_country to uk. > > -- > Tzafrir Cohen > icq#16849755 jabber:[EMAIL PROTECTED] > +972-50-7952406 mailto:[EMAIL PROTECTED] > http://www.xorcom.com iax:[EMAIL PROTECTED]/tzafrir > _______________________________________________ > --Bandwidth and Colocation provided by Easynews.com -- > > asterisk-users mailing list > To UNSUBSCRIBE or update options visit: > http://lists.digium.com/mailman/listinfo/asterisk-users > _______________________________________________ --Bandwidth and Colocation provided by Easynews.com -- asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users