Hi list, I'm evaluating a private telephony scenario of about 20 locations - 300 phones, 50 FAX machines.
Initial overview points to the installation of asterisk at three locations connected to the PSTN via ISDN PRI. All other locations, small by themselves, would get SIP phones managed by asterisk, since there is good IP connectivity between all sites. Now on to the subject... Handling FAXes: 1. On the locations where asterisk is installed, the solution is "trivial"; either by connecting FAXes to FXS ports on channelbanks or by managing faxes with iaxmodem + Hylafax. Probably a combination of both... 2. On the remaining locations "we have a problem" which I have been studying and trying to address... Faxing over IP. Side note: - I've read every recent mail on this mailing list regarding the subject - I've browsed the wiki to its fullest extent - I've googled a lot - I've read Steve Underwood's excelent summary on the subject (check it out at http://www.soft-switch.org/foip.html) Facts: a) FAX over VoIP will not work, so installing ATAs on the remote locations and bridging them with the PSTN FAXes is out of the plan. b) T.38 is the answer to FoIP c) asterisk 1.2 does not support T.38 d) asterisk 1.4 only does T.38 passthrough, not good enough e) CallWeaver seems to support T.38 gatewaying, although I'd rather move on with asterisk so as to leverage current experience and knowledge and to keep installed base with the same software. Possible solutions point to complementing asterisk installations with T.38 capable equipment. (of course, one other solution would be to subscribe to analog lines at each location! however, this would prevent us from performing FAX CDR accounting -- not a requirement, but a really nice-to-have). Having said all of this (and please correct me if I'm wrong) I'm looking for suggestions on how to best complement asterisk in such a scenario. The architecture I'm currently considering is: [PSTN] <---PRI---> [asterisk] <---PRI---> [PRI-to-T38 GW] ... ... <--SIP/T.38---> [T.38 ATA] <---FXS---> FAX machine On incoming faxes, asterisk would simply Dial() the PRI leading to the PRI-to-T.38 GW which would be configured, according to the dialed number, to connect via SIP/T.38 to the respective T.38 ATA. Outbound would have the PRI-to-T.38 GW work the other way around, calling asterisk with the PSTN FAX destination number... Again, asterisk would only have to Dial() out to the PSTN. My questions: 1. What do you think of it, Is it feasible ? Does it make any sense ? How would you do it differently and why ? 2. I believe a Cisco AS53xx + Cisco ATAs would do the job. What about a Patton SmartNode 4960 + Patton ATAs ? (I have very little knowledge about Cisco equipment, but I'm almost 100% sure the Ciscos would do it... on the other hand, I've read most of the Patton docs and, again, I'm also almost 100% sure these would do it -- however, hands on experience and knowledge counts a lot!) 3. Roughly, how much would one expect to pay for one such PRI-to-T.38 gateway ? 5k, 10k, 20k ? Probably the Cisco version will be more expensive, no ? 4. Of course, I could use CallWeaver as a PRI-to-T.38 gateway... But then again, how solid would it be ? With which ATAs ? The CallWeaver website shows a very small amount of ATAs confirmed to be 100% working in T.38. 5. Would I need to have a SIP proxy between the PRI-to-T.38 gw and the T.38 ATAs or would they be able to talk to each other directly ? (I'd say this would depend on the specific equipment, but...) If that would be a requirement, which way would you go, asterisk 1.4 ? Would SER forward T.38 traffic ? Thanks for inputs and experiences in complementing asterisk with T.38 equipment. -- exvito _______________________________________________ --Bandwidth and Colocation Provided by http://www.api-digital.com-- asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users