zttest: --- Results after 44 passes --- Best: 100.000000 -- Worst: 99.987793 -- Average: 99.988350
Dell 2950 Wildcard TE410P (2nd Gen) (rev 02) (with echo cancel daughter board) 1 PRI configured to Telco 1 PRI configured to old Panasonic DBS 576 being used just as a mux for our fax machines. -- -- Steven http://www.connectech.org/ "broadband Voice" <[EMAIL PROTECTED]> wrote in message news:[EMAIL PROTECTED] How did this workout? I am considering getting the Dell PowerEdge 2950. On 11/5/07, Steven <[EMAIL PROTECTED]> wrote: 2950s work fine. I have had the parity error for over a year with no noticable problems. It is working fine. I did have to make some IRQ changes to clean up the system. I did these on my Dell 1750 test machine, but have made the same changes on my production machine. The changes basically redue the IRQ load from other cards, like the RAID card, which will reduce the bus's capacity for processing all of the TDM IRQs. It also allocates just one CPU full time for all of the TDM IRQs. The changes are below: ref: FYI on zttool output on SMP system --- Results after 56 passes --- Best: 100.000000 -- Worst: 99.987793 -- Average: 99.999564 Only 2 were 99.987793, the 54 others were all 100.000000. I got this by making the changes below on my dual proc Dell 1750. setpci -v -s 01:08.1 LATENCY_TIMER=8 setpci -v -s 00:0f.1 LATENCY_TIMER=8 setpci -v -s 01:04.0 LATENCY_TIMER=8 setpci -v -s 01:02.0 LATENCY_TIMER=8 setpci -v -s 00:0f.2 LATENCY_TIMER=8 setpci -v -s 01:04.0 LATENCY_TIMER=8 (these are USB, SCSI HW RAID driver, Ethernet, Video, etc. I did not alter ZAP cards, nor any bridges or buses) echo 1 > /proc/irq/17/smp_affinity (Ethernet) echo 1 > /proc/irq/18/smp_affinity (SCSI HW RAID Driver) echo 2 > /proc/irq/20/smp_affinity (TDM) echo 2 > /proc/irq/24/smp_affinity (TE411P) I also turned of the startup of irqbalance. The setpci changes did the most work concerning reaching 100% in zttest. Irqbalance was causing the the processor handling the interrupts of the zap cards to change very often. This would impose a delay during the change and cause the zttest numbers to drop/be inconsistent. Because I turned irqbalance off, the irqs are processed round robin style, which is also not good. Therefore, I hard coded the processor affinity for the zap cards to one proc and all other high load irqs to the other proc. If you have more than 2 procs, you can spread them out even more. If you do not turn off irqbalance, the affinity changes will be overwritten by it. I made these changes on a live system without issue. I set these changes in /etc/rc.d/rc.local to reset them after reboots. -- -- Steven http://www.glimasoutheast.org "Brian Hutchinson" <[EMAIL PROTECTED]> wrote in message news:[EMAIL PROTECTED] You guys are scaring me! I'm building a 2950 with SAS RAID 5 on the new PERC and it will have 2 TE420P's. I hope it works or my bacon will fry. On 10/25/07, Joseph Begumisa <[EMAIL PROTECTED]> wrote: > > Has anyone had any compatibility issues with a TE110P card installed > on a Dell Poweredge 1950?I noted the following error on the LCD > display of the Dell Poweredge 1950: > > > > E1711 PCI PErr Slot 1 E171F PCIE Fatal Error B0 D4 F0. >Yes, I have had this problem with a dell PE1650, 1850, SC1400, and PE650. I have a TE410P that does it. It may not be wise, but I just ignore the orange blinking LCD display (or light, >depending on the model). I did try reseating the card, and it "works" for a few weeks, and then goes back to the same old thing. Yes, that happened too. Digium has graciously offered to send me a TE120P with the Digium VoiceBus technology which I will test out on the Dell 1950. Will post my findings thereafter. Joseph. _______________________________________________ --Bandwidth and Colocation Provided by http://www.api-digital.com-- asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users _______________________________________________ --Bandwidth and Colocation Provided by http://www.api-digital.com-- asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users _______________________________________________ --Bandwidth and Colocation Provided by http://www.api-digital.com-- asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users _______________________________________________ -- Bandwidth and Colocation Provided by http://www.api-digital.com -- asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users _______________________________________________ -- Bandwidth and Colocation Provided by http://www.api-digital.com -- asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users