Tzafrir Cohen wrote: > On Fri, Sep 05, 2008 at 09:47:48AM -0400, sean darcy wrote: >> Tzafrir Cohen wrote: >>> On Thu, Sep 04, 2008 at 10:58:44PM -0400, sean darcy wrote: >>>> As best i could figure it out, I've installed dahdi and rc4. >>>> >>>> My TDM400P doesn't answer fxo or fxs. >>>> >>>> /etc/dahdi/system.conf: >>>> loadzone = us >>>> defaultzone=us >>>> fxoks=1,2 >>>> fxsks=4 >>> echocancel? >>> >> I thought that if you had hardware echocancel ( TDM400P does, doesn't >> it? ), > > TDM400P doesn't. Do you mean TDM410P? > >> setting the software echocanceller was irrelevant. In any event, >> isn't mg2 the deefault? > > No. You may have that impression from the configuration generated by > dahdi_genconf that adds it as a default (that is: generates an explicit > echocancel line for each channel) due to this limitation. That may > change in the future if system.conf will grow up its own default echo > canceller. > >> I'll take the system down and change this, and dahdichan to 1,2 later >> today, though again that wouldn't explain the lack of call pickup on the >> _external_ line. show daahdi channels shows _no_ channels. ( sigh) > > And this still does not explain why you have not posted the output of: > > cat /proc/dahdi/* > > ;-) > >> And, I'm using 1.6.0-rc4. > I've got 1.6.0-rc4 up again.
cat /proc/dahdi/* Span 1: WCTDM/4 "Wildcard TDM400P REV I Board 5" (MASTER) 1 WCTDM/4/0 FXOKS 2 WCTDM/4/1 FXOKS 3 WCTDM/4/2 4 WCTDM/4/3 FXSKS and dahdi_cfg seems to have worked: dahdi_cfg -vv DAHDI Tools Version - 2.0.0-rc2 DAHDI Version: 2.0.0-rc3 Echo Canceller(s): Configuration ====================== Channel map: Channel 01: FXO Kewlstart (Default) (Slaves: 01) Channel 02: FXO Kewlstart (Default) (Slaves: 02) Channel 04: FXS Kewlstart (Default) (Slaves: 04) 3 channels to configure. Changing signalling on channel 1 from Unused to FXO Kewlstart Changing signalling on channel 2 from Unused to FXO Kewlstart Changing signalling on channel 4 from Unused to FXS Kewlstart but still no luck. No dial tone for the internal phones, no answer on pstn. *CLI> dahdi show status Description Alarms IRQ bpviol CRC4 Fra Codi Options LBO Wildcard TDM400P REV I Board 5 OK 0 0 0 CAS Unk YEL 0 db (CSU)/0-133 feet (DSX-1) *CLI> dahdi show channels Chan Extension Context Language MOH Interpret Blocked State pseudo default default In Service *CLI> dahdi show channel 1 Unable to find given channel 1 Command 'dahdi show channel 1' failed. cat /etc/dahdi/system.conf # note change in fxo_ks and fx2_ks. 1 & 2 are internal, 4 is extension fxoks=1,2 fxsks=4 loadzone = us defaultzone = us BTW, this file is sometimes referred to as dahdi.conf - to keep us on our toes. and what is the comment sign ; or # ? cat /etc/asterisk/chan_dahdi.conf [trunkgroups] [channels] usecallerid=yes callwaiting=yes usecallingpres=yes callwaitingcallerid=yes threewaycalling=yes transfer=yes canpark=yes cancallforward=yes callreturn=yes echocancel=no echocancelwhenbridged=no echotraining=no group=1 callgroup=1 pickupgroup=1 callprogress=yes progzone=us tonezone = 0 ; 0 is US jbenable = yes ; Enables the use of a jitterbuffer on the receiving side of a ; DAHDI channel. Defaults to "no". An enabled jitterbuffer will ; be used only if the sending side can create and the receiving ; side can not accept jitter. The DAHDI channel can't accept jitter, ; thus an enabled jitterbuffer on the receive DAHDI side will always ; be used if the sendi [home-phones] context=internal ; Uses the [internal] context in extensions.conf signalling=auto ; fxo_ks Use FXO signalling for an FXS channel - as set in sytem.conf.conf ;channel => 1 ; Telephone attached to port 1 ;channel => 2 ; Telephone attached to port 2 dahdichan => 1,2 [pstn] context=incoming-pstn-line ; Incoming calls go to [incoming-pstn-line] in extensions.conf signalling=auto ; fxs_ks Use FXS signalling for an FXO channel - use as set in system.conf faxdetect=incoming busydetect=yes ;channel => 4 dahdichan => 4 ; PSTN attached to port 4 Thanks for any help. sean _______________________________________________ -- Bandwidth and Colocation Provided by http://www.api-digital.com -- AstriCon 2008 - September 22 - 25 Phoenix, Arizona Register Now: http://www.astricon.net asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users