I don't mean to be a pain, but i could really do with a heads up on this... does anyone have ANY ideas? I've trawled through google and come up with nothing except for questions with no answers...
Cheers Geraint 2008/10/6 Geraint Lee <[EMAIL PROTECTED]> > Hi all, I've done this a few times with other PBX's but swyx has stumped > me! I'm having some trouble getting Asterisk connected to a Swyx system > using a sangoma A104dx... currently the setup is: > BT <-> Swyx > > The above setup works fine... what i'm trying to achieve is > BT & SIP Trunks <-> Asterisk <-> Swyx > > I have connected to our BT (2 x ISDN30 UK) with asterisk and have no errors > and can make and receive calls and it never dies... the problem comes when i > try and connect asterisk to swyx... > I can make calls from asterisk to the swyx system with no problems or > errors, but... when i try and place a call from Swyx to asterisk i receive > the following error: > [Oct 6 10:56:20] ERROR[9794]: chan_zap.c:8250 zt_pri_error: !! Unexpected > Channel selection 3 > > The call does complete as normal but after about 2 or 3 hours of calls > passing through this setup i start receiving errors like the following: > [Oct 6 10:55:25] WARNING[9794]: chan_zap.c:8074 pri_fixup_principle: Can't > fix up channel from 63 to 92 because 92 is already in use > [Oct 6 10:55:25] WARNING[9794]: chan_zap.c:9245 pri_dchannel: Hangup on > bad channel 0/30 on span 3 > [Oct 6 10:55:55] WARNING[9794]: chan_zap.c:8074 pri_fixup_principle: Can't > fix up channel from 63 to 92 because 92 is already in use > > And eventually no more calls can be placed from swyx to asterisk... time > for some configs... and before anyone says something about wanpipe3 and 4 > having dchan=0, i tried with dchan=16 and no calls can be placed... > > I hope someone can point me in the right direction as we're trying to get > rid of swyx since we're tied down by limiting software and excessive > licensing costs. > > Thanks! > > Geraint > > pri show spans shows all spans as up and active. > zap show status shows all as ok > wanrouter status shows all as connected > > wanpipe1 and 2: > [devices] > wanpipe1 = WAN_AFT_TE1, Comment > > [interfaces] > w1g1 = wanpipe1, , TDM_VOICE, Comment > > [wanpipe1] > CARD_TYPE = AFT > S514CPU = A > CommPort = PRI > AUTO_PCISLOT = NO > PCISLOT = 1 > PCIBUS = 16 > FE_MEDIA = E1 > FE_LCODE = HDB3 > FE_FRAME = CRC4 > FE_LINE = 1 > TE_CLOCK = NORMAL > TE_REF_CLOCK = 0 > TE_SIG_MODE = CCS > TE_HIGHIMPEDANCE = NO > LBO = 120OH > FE_TXTRISTATE = NO > MTU = 1500 > UDPPORT = 9000 > TTL = 255 > IGNORE_FRONT_END = NO > TDMV_SPAN = 1 > TDMV_DCHAN = 16 > TDMV_HW_DTMF = NO > > [w1g1] > ACTIVE_CH = ALL > TDMV_ECHO_OFF = NO > TDMV_HWEC = YES > > > wanpipe3 and 4: > [devices] > wanpipe3 = WAN_AFT_TE1, Comment > > [interfaces] > w3g1 = wanpipe3, , TDM_VOICE, Comment > > [wanpipe3] > CARD_TYPE = AFT > S514CPU = A > CommPort = PRI > AUTO_PCISLOT = NO > PCISLOT = 1 > PCIBUS = 16 > FE_MEDIA = E1 > FE_LCODE = HDB3 > FE_FRAME = CRC4 > FE_LINE = 3 > TE_CLOCK = MASTER > TE_REF_CLOCK = 1 > TE_SIG_MODE = CCS > TE_HIGHIMPEDANCE = NO > LBO = 120OH > FE_TXTRISTATE = NO > MTU = 1500 > UDPPORT = 9000 > TTL = 255 > IGNORE_FRONT_END = NO > TDMV_SPAN = 3 > TDMV_DCHAN = 0 > TDMV_HW_DTMF = NO > > [w3g1] > ACTIVE_CH = ALL > TDMV_ECHO_OFF = NO > TDMV_HWEC = YES > > zaptel.conf: > loadzone=uk > defaultzone=uk > > #Sangoma A104 port 1 [slot:1 bus:16 span:1] <wanpipe1> > span=1,0,0,ccs,hdb3,crc4 > bchan=1-15,17-31 > hardhdlc=16 > > #Sangoma A104 port 2 [slot:1 bus:16 span:2] <wanpipe2> > span=2,0,0,ccs,hdb3,crc4 > bchan=32-46,48-62 > hardhdlc=47 > > #Sangoma A104 port 3 [slot:1 bus:16 span:3] <wanpipe3> > span=3,0,0,ccs,hdb3,crc4 > bchan=63-77,79-93 > dchan=78 > > #Sangoma A104 port 4 [slot:1 bus:16 span:4] <wanpipe4> > span=4,0,0,ccs,hdb3,crc4 > bchan=94-108,110-124 > dchan=109 > > I have also tried with hardhdlc=109 and have the same problem. > > zapata.conf: > [channels] > language=en > usecallerid=yes > hidecallerid=no > callwaiting=no > callwaitingcallerid=yes > restrictcid=no > usecallingpres=no > threewaycalling=yes > callreturn=yes > transfer=yes > cancallforward=yes > musiconhold=default > rxgain=0.0 > txgain=0.0 > immediate=no > > ; BT > switchtype=euroisdn > group=1 > context=from-bt > signalling=pri_cpe > > ; Port 1 - BT > channel => 1-15,17-31 > > ; Port 2 - BT > channel => 32-46,48-62 > > ; Swyx > overlapdial=yes > group=2 > context=from-swyx > signalling=pri_net > > ; Port 3 - Swyx > channel => 63-77,79-93 > > ; Port 4 - Swyx > channel => 94-108,110-124 >
_______________________________________________ -- Bandwidth and Colocation Provided by http://www.api-digital.com -- AstriCon 2008 - September 22 - 25 Phoenix, Arizona Register Now: http://www.astricon.net asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users