I have a TDM400 working quite well, Digium dialled in and recompiled
chan_zap with some changes , to get BT Callerid working and I have set
hangup on polarity in the zaptel.conf which seems to work well
this is a BT home line, not business, if you have a business line you
should get the DCT set to 800ms and the disconnect clear should work
Robb
Gordon Henderson wrote:
On Fri, 10 Oct 2008, Luis Morales wrote:
Ok!!
Do this finale test.
Who, me or the OP (Mike). My setup works OK and I've no intention of
doing tests, final or otherwise, thanks.
Gordon
call fron analog lines to any number, wait until the called hang up.
Now tell us the signal tone. If the signal is busy ? or any thing
else....
Your set up look ok. Now try with this options into zapata.conf header:
zapata.conf:
usecallerid=yes
hidecallerid=no
callwaiting=no
threewaycalling=yes
transfer=yes
echocancelwhenbridged=no
immediate=no
faxdetect=no
busydetect=yes
busycount=4
On Fri, Oct 10, 2008 at 11:42 AM, Gordon Henderson
<[EMAIL PROTECTED]> wrote:
On Thu, 9 Oct 2008, Mike wrote:
Folks,
I've seen a few reports that people have had problems with hang up
detection on UK cable phone lines. I have a TDM400P with two FXO
ports,
one connected to my BT line and the other connected to my
Telewest/Virgin Media cable line. If I ring the BT line and then
clear
down, Asterisk detects this and acts accordingly. If I ring the
Telewest line, the clear down is not detected, hence Asterisk
continues
to ring extentions, record voicemail, etc.
I've seen a few posts reporting this issue with the UK cable system
but
these are generally not resolved.
Has anyone sucessfully configured a UK Telewest line with Astersik?
Does anyone know how Telewest signals that the remote caller has
cleared
down?
I did an instalaltion yesterday with 2 Teleworst lines.
When I was calling in on my mobile, then hanging up, it seemed to
work ok
- it did keep the line open for a few seconds, but I see that with
BT too.
On the same topic, how does BT signal remote clear down?
Dunno...
I have plugged a phone into the Telewest line and it doesn't appear to
receive a tone on clear down, nor does it appear to drop power on the
line. Just in case, I changed the DCT in zaptel.h from 500ms to
100ms and
recompiled, however, this did not resolve the issue.
I'm using asterisk 1.2.30, Zaptel 1.2.24. Oslec and an OpenVox card.
I'm working blind at the moment as I cannot find anything which
documents what to expect the Telewest line to do to signal a remote
clear down occured. I've played around with the kewlstart and
loop-start setting but without knowing what the line is going to do,
it's difficult to know how to configure Asterisk.
Does anyone have any experience of Telewest?
Only 2 sites and they both seem to work OK - One in Bristol the
other in
Plymouth.
Can't get caller ID to work though )-:
Zaptel.conf:
fxsks=3
fxsks=4
loadzone=uk
defaultzone=uk
zapata.conf:
usecallerid=yes
cidsignalling=v23
cidstart=polarity
hidecallerid=no
callwaiting=no
threewaycalling=yes
transfer=yes
echocancel=256
;echocancel=yes
;echotraining=yes
echocancelwhenbridged=no
immediate=no
faxdetect=no
; Channel 3: PSTN line
context=incoming
group=1
usecallerid=no
faxdetect=none
signalling=fxs_ks
rxgain=4
txgain=4
callerid=asreceived
channel => 3
; Channel 4: PSTN line
context=incoming
group=1
usecallerid=no
faxdetect=none
signalling=fxs_ks
rxgain=4
txgain=4
callerid=asreceived
channel => 4
Gordon
_______________________________________________
-- Bandwidth and Colocation Provided by http://www.api-digital.com --
asterisk-users mailing list
To UNSUBSCRIBE or update options visit:
http://lists.digium.com/mailman/listinfo/asterisk-users
--
---------------------------------------------------------------------------------
Luis Morales
Consultor de Tecnologia
Cel: +(58)416-4242091
---------------------------------------------------------------------------------
"Empieza por hacer lo necesario, luego lo que es posible... y de
pronto estarás haciendo lo imposible"
Leonardo Da'Vinci
---------------------------------------------------------------------------------
_______________________________________________
-- Bandwidth and Colocation Provided by http://www.api-digital.com --
asterisk-users mailing list
To UNSUBSCRIBE or update options visit:
http://lists.digium.com/mailman/listinfo/asterisk-users
------------------------------------------------------------------------
_______________________________________________
-- Bandwidth and Colocation Provided by http://www.api-digital.com --
asterisk-users mailing list
To UNSUBSCRIBE or update options visit:
http://lists.digium.com/mailman/listinfo/asterisk-users
_______________________________________________
-- Bandwidth and Colocation Provided by http://www.api-digital.com --
asterisk-users mailing list
To UNSUBSCRIBE or update options visit:
http://lists.digium.com/mailman/listinfo/asterisk-users
