Sorry for bothering you, but I got it, I just had to put # in callnum!
On Sat, Jan 17, 2009 at 1:44 AM, Pascal Bruno <tipas...@gmail.com> wrote: > I want to dial out using the sim card. What I did, I have used the SIP > channel ex: > > Channel: SIP/thenum...@mv378 > > It shows the called is being made in the dialplan, but the number I have > entered does not dial, it just goes straight to the specified dialplan > extensions. > > Then what I did, in the Lan to Mobile Table, I put * in url and the number > I wanted to dial in call num, then the call was made to that number using > the sim card properly. > > I was wondering if I cannot supply the number to be dialed using an > asterisk call file, or do I have to put that number in the Lan to Mobile > table. > > Any help would be appreciated. > > Thanks > > > > > > On Sat, Jan 17, 2009 at 12:39 AM, Pascal Bruno <tipas...@gmail.com> wrote: > >> Marco, >> >> The configs work fine for me. I can receive calls with no problem. Now, >> were you able to dial using the sim card? I cant figure out how I can do it >> since asterisk doesnt have a channel to place call through the portech >> gateway. >> >> >> >> >> >> On Fri, Jan 16, 2009 at 12:04 PM, Pascal Bruno <tipas...@gmail.com>wrote: >> >>> Thank you!, I will try that in a few hours and let you know what happens. >>> >>> >>> >>> On Fri, Jan 16, 2009 at 11:01 AM, Marco Signorini >>> <marcota...@libero.it>wrote: >>> >>>> >>>> >>>> Pascal Bruno wrote: >>>> >>>> Thanks for your reply! >>>> >>>> Can you tell me what you have in your Portech configuration settings >>>> (Mobile to Lan Settings; Sip Proxy settings etc...) My sip.conf file is >>>> pretty similar to yours but still cant register. >>>> >>>> >>>> >>>> On Fri, Jan 16, 2009 at 3:47 AM, Marco Signorini >>>> <marcota...@libero.it>wrote: >>>> >>>>> Emmanuel Pascal Bruno wrote: >>>>> >>>>> Has anyone been able to configure portech's mv-378 gateway with >>>>> asterisk? >>>>> >>>>> I did the configuration as per the manual but it does not work. >>>>> >>>>> My server sees the portech gateway, but when the gateway is trying to >>>>> register to my server it fails. It says peer is not suppose to register. >>>>> >>>>> The gateway and the asterisk box are on two different location (two >>>>> network, 2 differrent IP address). >>>>> >>>>> I would appreciate any kind of tutorial or advice on how to make it >>>>> work. >>>>> >>>>> Thanks >>>>> >>>>> ------------------------------ >>>>> >>>>> _______________________________________________ >>>>> -- Bandwidth and Colocation Provided by http://www.api-digital.com -- >>>>> >>>>> asterisk-users mailing list >>>>> To UNSUBSCRIBE or update options visit: >>>>> http://lists.digium.com/mailman/listinfo/asterisk-users >>>>> >>>>> >>>>> Hi, >>>>> I've an installation working with Portech MV-370. I'm supposing it's >>>>> quite similar to what you have. If it could be useful to you, this is my >>>>> sip.conf configuration file. >>>>> >>>>> [GSMGtw1] >>>>> type=friend >>>>> context=from-gsm >>>>> host=dynamic ; we have a DHCP assigned address >>>>> secret=reallyverysecret >>>>> nat=no ; there is not NAT between phone and >>>>> Asterisk >>>>> canreinvite=no >>>>> dtmfmode=INFO >>>>> insecure=invite ; required to overcome authentication >>>>> problems in incoming calls >>>>> call-limit=1 ; permit only 1 outgoing call at a >>>>> time >>>>> disallow=all >>>>> allow=ulaw >>>>> allow=alaw >>>>> allow=gsm >>>>> qualify=500 >>>>> >>>>> I remember that I've found a bug on the firmware that prevents to the >>>>> unit to register correctly on my asterisk box unless I'm using the raw IP >>>>> address instead of the name of the asterisk box. I remember something >>>>> wrong >>>>> in cryptography chiper/dechiper based on realm... So, if you have >>>>> problems, >>>>> let's try to specify the asterisk raw IP address in the Portech. >>>>> >>>>> Best regards, >>>>> Marco Signorini. >>>>> >>>>> >>>>> >>>> Hi, >>>> >>>> I don't know if the problem could be in the Mobile to Lan or Lan to >>>> Mobile settings because these settings are related on how calls coming >>>> from/to mobile are routed. I didn't use the Portech routing features at >>>> all >>>> because I need a simple GSM gateway to/from the asterisk box. >>>> For this reason: >>>> 1. The only rule I've on Mobile to Lan is CID=*; url=...@192.168.0.5where >>>> "mob" is the extension I've generated in the asterisk box under the >>>> context where the Portech operates; >>>> 2. The only rule I've on Lan to Mobile is URL=*; Call Num=# >>>> >>>> I think the most relevant parameters for your problem are under the >>>> "Service Domain" menu option (assuming that the firmware you have is >>>> similar >>>> to what I've). On this menu I've compiled the 1st Realm (as I've only one >>>> account) like that: >>>> >>>> UserName: GSMGtw1 >>>> RegisterName: GSMGtw1 >>>> RegisterPassword: reallyverysecret >>>> Domain Server: 192.168.0.5 >>>> Proxy Server: 192.168.0.5 >>>> >>>> Pay attention that, having specified the Domain Server with the raw IP >>>> address, asterisk needs to be able to authenticate peers associated to >>>> that. >>>> For this reason I've set: >>>> >>>> domain=192.168.0.5 >>>> >>>> on sip.conf [general] section (remember to issue a sip reload from >>>> asterisk cli). >>>> >>>> Hope this helps! >>>> >>>> >>>> Best regards. >>>> Marco Signorini >>>> >>>> >>>> >>>> ======================== >>>> Marco Signorini >>>> INGEGNI Tech S.r.l. >>>> http://www.ingegnitech.com >>>> >>>> _______________________________________________ >>>> -- Bandwidth and Colocation Provided by http://www.api-digital.com -- >>>> >>>> asterisk-users mailing list >>>> To UNSUBSCRIBE or update options visit: >>>> http://lists.digium.com/mailman/listinfo/asterisk-users >>>> >>> >>> >> >
_______________________________________________ -- Bandwidth and Colocation Provided by http://www.api-digital.com -- asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users