Stephen J. Wilcox wrote: You are trying to have both ends act as users, cisco can support emulating a network interface (isdn protocol-emulate in serial interface config) but in my experience i could get the circuit up but it would bounce and i couldnt get signalling to work.. to be fair my IOS is quite old and wouldnt support the switch types that I think I needed Steve, My circuit is up but I have signalling problem. Port becomes up and down, up and down,.... I changed something at Cisco conf, please give me a clue. (I have some "-- T200 counter expired, What to do..." and other T203 messages, could it be timing problem?). Also, I am sending my PRI INTENSE DEBUG output. My New Cisco Conf: ! Cisco AS5300 - ios c5300-is-mz.122-5.bin isdn switch-type primary-ni isdn voice-call-failure 0 controller E1 3 framing NO-CRC4 pri-group timeslots 1-31 interface Serial3:15 no ip address isdn switch-type primary-ni isdn protocol-emulate network isdn guard-timer 2000 isdn T203 10000 isdn T306 3000 isdn T310 60000 isdn bchan-number-order ascending no cdp enable My INTENSE debug output: > [ > [00 > [00 01 > [00 01 01 > [00 01 01 01 > [00 01 01 01 ] > [00 01 01 01 ] > Supervisory frame: > SAPI: 00 C/R: 0 EA: 0 > TEI: 000 EA: 1 > Zero: 0 S: 0 01: 1 [ RR (receive ready) ] > N(R): 000 P/F: 1 > 0 bytes of data -- Restarting T203 counter > [ > [00 > [00 01 > [00 01 00 > [00 01 00 00 > [00 01 00 00 08 > [00 01 00 00 08 02 > [00 01 00 00 08 02 00 > [00 01 00 00 08 02 00 00 > [00 01 00 00 08 02 00 00 46 > [00 01 00 00 08 02 00 00 46 18 > [00 01 00 00 08 02 00 00 46 18 03 > [00 01 00 00 08 02 00 00 46 18 03 a9 > [00 01 00 00 08 02 00 00 46 18 03 a9 83 > [00 01 00 00 08 02 00 00 46 18 03 a9 83 9c > [00 01 00 00 08 02 00 00 46 18 03 a9 83 9c 79 > [00 01 00 00 08 02 00 00 46 18 03 a9 83 9c 79 01 > [00 01 00 00 08 02 00 00 46 18 03 a9 83 9c 79 01 80 > [00 01 00 00 08 02 00 00 46 18 03 a9 83 9c 79 01 80 ] > [00 01 00 00 08 02 00 00 46 18 03 a9 83 9c 79 01 80 ] > Informational frame: > SAPI: 00 C/R: 0 EA: 0 > TEI: 000 EA: 1 > N(S): 000 0: 0 > N(R): 000 P: 0 > 13 bytes of data -- Restarting T203 counter Stopping T_203 timer Starting T_200 timer > Protocol Discriminator: Q.931 (8) len=13 > Call Ref: len= 2 (reference 0/0x0) (Originator) > Message type: RESTART (70) > Channel ID (len= 5) [ Ext: 1 IntID: Implicit, PRI Spare: 0, Exclusive Dchan: 0 > ChanSel: Reserved > Ext: 1 Coding: 0 Number Specified Channel Type: 3 > Ext: 1 Channel: 28 ] > Restart Indentifier: [ Ext: 1 Spare: 0 Resetting Indicated Channel (0) ] -- T200 counter expired, What to do... -- Retransmitting 17 bytes > [ > [00 > [00 01 > [00 01 00 > [00 01 00 01 > [00 01 00 01 08 > [00 01 00 01 08 02 > [00 01 00 01 08 02 00 > [00 01 00 01 08 02 00 00 > [00 01 00 01 08 02 00 00 46 > [00 01 00 01 08 02 00 00 46 18 > [00 01 00 01 08 02 00 00 46 18 03 > [00 01 00 01 08 02 00 00 46 18 03 a9 > [00 01 00 01 08 02 00 00 46 18 03 a9 83 > [00 01 00 01 08 02 00 00 46 18 03 a9 83 9c > [00 01 00 01 08 02 00 00 46 18 03 a9 83 9c 79 > [00 01 00 01 08 02 00 00 46 18 03 a9 83 9c 79 01 > [00 01 00 01 08 02 00 00 46 18 03 a9 83 9c 79 01 80 > [00 01 00 01 08 02 00 00 46 18 03 a9 83 9c 79 01 80 ] > [00 01 00 01 08 02 00 00 46 18 03 a9 83 9c 79 01 80 ] > Informational frame: > SAPI: 00 C/R: 0 EA: 0 > TEI: 000 EA: 1 > N(S): 000 0: 0 > N(R): 000 P: 1 > 13 bytes of data -- Rescheduling retransmission (1) < [ < [00 < [00 01 < [00 01 01 < [00 01 01 03 < [00 01 01 03 ] < [00 01 01 03 ] < Supervisory frame: < SAPI: 00 C/R: 0 EA: 0 < TEI: 000 EA: 1 < Zero: 0 S: 0 01: 1 [ RR (receive ready) ] < N(R): 001 P/F: 1 < 0 bytes of data -- ACKing all packets from 0 to (but not including) 1 -- ACKing packet 0, new txqueue is -1 (-1 means empty) -- Since there was nothing left, stopping T200 counter -- Nothing left, starting T203 counter -- Got RR response to our frame -- Restarting T203 counter < [ < [02 < [02 01 < [02 01 00 < [02 01 00 02 < [02 01 00 02 08 < [02 01 00 02 08 02 < [02 01 00 02 08 02 80 < [02 01 00 02 08 02 80 00 < [02 01 00 02 08 02 80 00 4e < [02 01 00 02 08 02 80 00 4e 18 < [02 01 00 02 08 02 80 00 4e 18 03 < [02 01 00 02 08 02 80 00 4e 18 03 a9 < [02 01 00 02 08 02 80 00 4e 18 03 a9 83 < [02 01 00 02 08 02 80 00 4e 18 03 a9 83 9c < [02 01 00 02 08 02 80 00 4e 18 03 a9 83 9c 79 < [02 01 00 02 08 02 80 00 4e 18 03 a9 83 9c 79 01 < [02 01 00 02 08 02 80 00 4e 18 03 a9 83 9c 79 01 80 < [02 01 00 02 08 02 80 00 4e 18 03 a9 83 9c 79 01 80 ] < [02 01 00 02 08 02 80 00 4e 18 03 a9 83 9c 79 01 80 ] < Informational frame: < SAPI: 00 C/R: 1 EA: 0 < TEI: 000 EA: 1 < N(S): 000 0: 0 < N(R): 001 P: 0 < 13 bytes of data -- ACKing all packets from 0 to (but not including) 1 -- Since there was nothing left, stopping T200 counter -- Stopping T203 counter since we got an ACK -- Nothing left, starting T203 counter < Protocol Discriminator: Q.931 (8) len=13 < Call Ref: len= 2 (reference 32768/0x8000) (Terminator) < Message type: RESTART ACKNOWLEDGE (78) < Channel ID (len= 5) [ Ext: 1 IntID: Implicit, PRI Spare: 0, Exclusive Dchan: 0 < ChanSel: Reserved < Ext: 1 Coding: 0 Number Specified Channel Type: 3 < Ext: 1 Channel: 28 ] < Restart Indentifier: [ Ext: 1 Spare: 0 Resetting Indicated Channel (0) ] Sending Receiver Ready (1) > [ > [02 > [02 01 > [02 01 01 > [02 01 01 02 > [02 01 01 02 ] > [02 01 01 02 ] > Supervisory frame: > SAPI: 00 C/R: 1 EA: 0 > TEI: 000 EA: 1 > Zero: 0 S: 0 01: 1 [ RR (receive ready) ] > N(R): 001 P/F: 0 > 0 bytes of data -- Restarting T203 counter -- Restarting T203 counter > [ > [00 > [00 01 > [00 01 02 > [00 01 02 02 > [00 01 02 02 08 > [00 01 02 02 08 02 > [00 01 02 02 08 02 00 > [00 01 02 02 08 02 00 00 > [00 01 02 02 08 02 00 00 46 > [00 01 02 02 08 02 00 00 46 18 > [00 01 02 02 08 02 00 00 46 18 03 > [00 01 02 02 08 02 00 00 46 18 03 a9 > [00 01 02 02 08 02 00 00 46 18 03 a9 83 > [00 01 02 02 08 02 00 00 46 18 03 a9 83 9d > [00 01 02 02 08 02 00 00 46 18 03 a9 83 9d 79 > [00 01 02 02 08 02 00 00 46 18 03 a9 83 9d 79 01 > [00 01 02 02 08 02 00 00 46 18 03 a9 83 9d 79 01 80 > [00 01 02 02 08 02 00 00 46 18 03 a9 83 9d 79 01 80 ] > [00 01 02 02 08 02 00 00 46 18 03 a9 83 9d 79 01 80 ] > Informational frame: > SAPI: 00 C/R: 0 EA: 0 > TEI: 000 EA: 1 > N(S): 001 0: 0 > N(R): 001 P: 0 > 13 bytes of data -- Restarting T203 counter Stopping T_203 timer Starting T_200 timer > Protocol Discriminator: Q.931 (8) len=13 > Call Ref: len= 2 (reference 0/0x0) (Originator) > Message type: RESTART (70) > Channel ID (len= 5) [ Ext: 1 IntID: Implicit, PRI Spare: 0, Exclusive Dchan: 0 > ChanSel: Reserved > Ext: 1 Coding: 0 Number Specified Channel Type: 3 > Ext: 1 Channel: 29 ] > Restart Indentifier: [ Ext: 1 Spare: 0 Resetting Indicated Channel (0) ] < [ < [00 < [00 01 < [00 01 01 < [00 01 01 04 < [00 01 01 04 ] < [00 01 01 04 ] < Supervisory frame: < SAPI: 00 C/R: 0 EA: 0 < TEI: 000 EA: 1 < Zero: 0 S: 0 01: 1 [ RR (receive ready) ] < N(R): 002 P/F: 0 < 0 bytes of data -- ACKing all packets from 0 to (but not including) 2 -- ACKing packet 1, new txqueue is -1 (-1 means empty) -- Since there was nothing left, stopping T200 counter -- Nothing left, starting T203 counter -- Restarting T203 counter < [ < [02 < [02 01 < [02 01 02 < [02 01 02 04 < [02 01 02 04 08 < [02 01 02 04 08 02 < [02 01 02 04 08 02 80 < [02 01 02 04 08 02 80 00 < [02 01 02 04 08 02 80 00 4e < [02 01 02 04 08 02 80 00 4e 18 < [02 01 02 04 08 02 80 00 4e 18 03 < [02 01 02 04 08 02 80 00 4e 18 03 a9 < [02 01 02 04 08 02 80 00 4e 18 03 a9 83 < [02 01 02 04 08 02 80 00 4e 18 03 a9 83 9d < [02 01 02 04 08 02 80 00 4e 18 03 a9 83 9d 79 < [02 01 02 04 08 02 80 00 4e 18 03 a9 83 9d 79 01 < [02 01 02 04 08 02 80 00 4e 18 03 a9 83 9d 79 01 80 < [02 01 02 04 08 02 80 00 4e 18 03 a9 83 9d 79 01 80 ] < [02 01 02 04 08 02 80 00 4e 18 03 a9 83 9d 79 01 80 ] < Informational frame: < SAPI: 00 C/R: 1 EA: 0 < TEI: 000 EA: 1 < N(S): 001 0: 0 < N(R): 002 P: 0 < 13 bytes of data -- ACKing all packets from 1 to (but not including) 2 -- Since there was nothing left, stopping T200 counter -- Stopping T203 counter since we got an ACK -- Nothing left, starting T203 counter < Protocol Discriminator: Q.931 (8) len=13 < Call Ref: len= 2 (reference 32768/0x8000) (Terminator) < Message type: RESTART ACKNOWLEDGE (78) < Channel ID (len= 5) [ Ext: 1 IntID: Implicit, PRI Spare: 0, Exclusive Dchan: 0 < ChanSel: Reserved < Ext: 1 Coding: 0 Number Specified Channel Type: 3 < Ext: 1 Channel: 29 ] < Restart Indentifier: [ Ext: 1 Spare: 0 Resetting Indicated Channel (0) ] Sending Receiver Ready (2) > [ > [02 > [02 01 > [02 01 01 > [02 01 01 04 > [02 01 01 04 ] > [02 01 01 04 ] > Supervisory frame: > SAPI: 00 C/R: 1 EA: 0 > TEI: 000 EA: 1 > Zero: 0 S: 0 01: 1 [ RR (receive ready) ] > N(R): 002 P/F: 0 > 0 bytes of data -- Restarting T203 counter -- Restarting T203 counter > [ > [00 > [00 01 > [00 01 04 > [00 01 04 04 > [00 01 04 04 08 > [00 01 04 04 08 02 > [00 01 04 04 08 02 00 > [00 01 04 04 08 02 00 00 > [00 01 04 04 08 02 00 00 46 > [00 01 04 04 08 02 00 00 46 18 > [00 01 04 04 08 02 00 00 46 18 03 > [00 01 04 04 08 02 00 00 46 18 03 a9 > [00 01 04 04 08 02 00 00 46 18 03 a9 83 > [00 01 04 04 08 02 00 00 46 18 03 a9 83 9e > [00 01 04 04 08 02 00 00 46 18 03 a9 83 9e 79 > [00 01 04 04 08 02 00 00 46 18 03 a9 83 9e 79 01 > [00 01 04 04 08 02 00 00 46 18 03 a9 83 9e 79 01 80 > [00 01 04 04 08 02 00 00 46 18 03 a9 83 9e 79 01 80 ] > [00 01 04 04 08 02 00 00 46 18 03 a9 83 9e 79 01 80 ] > Informational frame: > SAPI: 00 C/R: 0 EA: 0 > TEI: 000 EA: 1 > N(S): 002 0: 0 > N(R): 002 P: 0 > 13 bytes of data -- Restarting T203 counter Stopping T_203 timer Starting T_200 timer > Protocol Discriminator: Q.931 (8) len=13 > Call Ref: len= 2 (reference 0/0x0) (Originator) > Message type: RESTART (70) > Channel ID (len= 5) [ Ext: 1 IntID: Implicit, PRI Spare: 0, Exclusive Dchan: 0 > ChanSel: Reserved > Ext: 1 Coding: 0 Number Specified Channel Type: 3 > Ext: 1 Channel: 30 ] > Restart Indentifier: [ Ext: 1 Spare: 0 Resetting Indicated Channel (0) ] < [ < [00 < [00 01 < [00 01 01 < [00 01 01 06 < [00 01 01 06 ] < [00 01 01 06 ] < Supervisory frame: < SAPI: 00 C/R: 0 EA: 0 < TEI: 000 EA: 1 < Zero: 0 S: 0 01: 1 [ RR (receive ready) ] < N(R): 003 P/F: 0 < 0 bytes of data -- ACKing all packets from 1 to (but not including) 3 -- ACKing packet 2, new txqueue is -1 (-1 means empty) -- Since there was nothing left, stopping T200 counter -- Nothing left, starting T203 counter -- Restarting T203 counter < [ < [02 < [02 01 < [02 01 04 < [02 01 04 06 < [02 01 04 06 08 < [02 01 04 06 08 02 < [02 01 04 06 08 02 80 < [02 01 04 06 08 02 80 00 < [02 01 04 06 08 02 80 00 4e < [02 01 04 06 08 02 80 00 4e 18 < [02 01 04 06 08 02 80 00 4e 18 03 < [02 01 04 06 08 02 80 00 4e 18 03 a9 < [02 01 04 06 08 02 80 00 4e 18 03 a9 83 < [02 01 04 06 08 02 80 00 4e 18 03 a9 83 9e < [02 01 04 06 08 02 80 00 4e 18 03 a9 83 9e 79 < [02 01 04 06 08 02 80 00 4e 18 03 a9 83 9e 79 01 < [02 01 04 06 08 02 80 00 4e 18 03 a9 83 9e 79 01 80 < [02 01 04 06 08 02 80 00 4e 18 03 a9 83 9e 79 01 80 ] < [02 01 04 06 08 02 80 00 4e 18 03 a9 83 9e 79 01 80 ] < Informational frame: < SAPI: 00 C/R: 1 EA: 0 < TEI: 000 EA: 1 < N(S): 002 0: 0 < N(R): 003 P: 0 < 13 bytes of data -- ACKing all packets from 2 to (but not including) 3 -- Since there was nothing left, stopping T200 counter -- Stopping T203 counter since we got an ACK -- Nothing left, starting T203 counter < Protocol Discriminator: Q.931 (8) len=13 < Call Ref: len= 2 (reference 32768/0x8000) (Terminator) < Message type: RESTART ACKNOWLEDGE (78) < Channel ID (len= 5) [ Ext: 1 IntID: Implicit, PRI Spare: 0, Exclusive Dchan: 0 < ChanSel: Reserved < Ext: 1 Coding: 0 Number Specified Channel Type: 3 < Ext: 1 Channel: 30 ] < Restart Indentifier: [ Ext: 1 Spare: 0 Resetting Indicated Channel (0) ] Sending Receiver Ready (3) > [ > [02 > [02 01 > [02 01 01 > [02 01 01 06 > [02 01 01 06 ] > [02 01 01 06 ] > Supervisory frame: > SAPI: 00 C/R: 1 EA: 0 > TEI: 000 EA: 1 > Zero: 0 S: 0 01: 1 [ RR (receive ready) ] > N(R): 003 P/F: 0 > 0 bytes of data -- Restarting T203 counter -- Restarting T203 counter > [ > [00 > [00 01 > [00 01 06 > [00 01 06 06 > [00 01 06 06 08 > [00 01 06 06 08 02 > [00 01 06 06 08 02 00 > [00 01 06 06 08 02 00 00 > [00 01 06 06 08 02 00 00 46 > [00 01 06 06 08 02 00 00 46 18 > [00 01 06 06 08 02 00 00 46 18 03 > [00 01 06 06 08 02 00 00 46 18 03 a9 > [00 01 06 06 08 02 00 00 46 18 03 a9 83 > [00 01 06 06 08 02 00 00 46 18 03 a9 83 9f > [00 01 06 06 08 02 00 00 46 18 03 a9 83 9f 79 > [00 01 06 06 08 02 00 00 46 18 03 a9 83 9f 79 01 > [00 01 06 06 08 02 00 00 46 18 03 a9 83 9f 79 01 80 > [00 01 06 06 08 02 00 00 46 18 03 a9 83 9f 79 01 80 ] > [00 01 06 06 08 02 00 00 46 18 03 a9 83 9f 79 01 80 ] > Informational frame: > SAPI: 00 C/R: 0 EA: 0 > TEI: 000 EA: 1 > N(S): 003 0: 0 > N(R): 003 P: 0 > 13 bytes of data -- Restarting T203 counter Stopping T_203 timer Starting T_200 timer > Protocol Discriminator: Q.931 (8) len=13 > Call Ref: len= 2 (reference 0/0x0) (Originator) > Message type: RESTART (70) > Channel ID (len= 5) [ Ext: 1 IntID: Implicit, PRI Spare: 0, Exclusive Dchan: 0 > ChanSel: Reserved > Ext: 1 Coding: 0 Number Specified Channel Type: 3 > Ext: 1 Channel: 31 ] > Restart Indentifier: [ Ext: 1 Spare: 0 Resetting Indicated Channel (0) ] < [ < [00 < [00 01 < [00 01 01 < [00 01 01 08 < [00 01 01 08 ] < [00 01 01 08 ] < Supervisory frame: < SAPI: 00 C/R: 0 EA: 0 < TEI: 000 EA: 1 < Zero: 0 S: 0 01: 1 [ RR (receive ready) ] < N(R): 004 P/F: 0 < 0 bytes of data -- ACKing all packets from 2 to (but not including) 4 -- ACKing packet 3, new txqueue is -1 (-1 means empty) -- Since there was nothing left, stopping T200 counter -- Nothing left, starting T203 counter -- Restarting T203 counter < [ < [02 < [02 01 < [02 01 06 < [02 01 06 08 < [02 01 06 08 08 < [02 01 06 08 08 02 < [02 01 06 08 08 02 80 < [02 01 06 08 08 02 80 00 < [02 01 06 08 08 02 80 00 4e < [02 01 06 08 08 02 80 00 4e 18 < [02 01 06 08 08 02 80 00 4e 18 03 < [02 01 06 08 08 02 80 00 4e 18 03 a9 < [02 01 06 08 08 02 80 00 4e 18 03 a9 83 < [02 01 06 08 08 02 80 00 4e 18 03 a9 83 9f < [02 01 06 08 08 02 80 00 4e 18 03 a9 83 9f 79 < [02 01 06 08 08 02 80 00 4e 18 03 a9 83 9f 79 01 < [02 01 06 08 08 02 80 00 4e 18 03 a9 83 9f 79 01 80 < [02 01 06 08 08 02 80 00 4e 18 03 a9 83 9f 79 01 80 ] < [02 01 06 08 08 02 80 00 4e 18 03 a9 83 9f 79 01 80 ] < Informational frame: < SAPI: 00 C/R: 1 EA: 0 < TEI: 000 EA: 1 < N(S): 003 0: 0 < N(R): 004 P: 0 < 13 bytes of data -- ACKing all packets from 3 to (but not including) 4 -- Since there was nothing left, stopping T200 counter -- Stopping T203 counter since we got an ACK -- Nothing left, starting T203 counter < Protocol Discriminator: Q.931 (8) len=13 < Call Ref: len= 2 (reference 32768/0x8000) (Terminator) < Message type: RESTART ACKNOWLEDGE (78) < Channel ID (len= 5) [ Ext: 1 IntID: Implicit, PRI Spare: 0, Exclusive Dchan: 0 < ChanSel: Reserved < Ext: 1 Coding: 0 Number Specified Channel Type: 3 < Ext: 1 Channel: 31 ] < Restart Indentifier: [ Ext: 1 Spare: 0 Resetting Indicated Channel (0) ] Sending Receiver Ready (4) > [ > [02 > [02 01 > [02 01 01 > [02 01 01 08 > [02 01 01 08 ] > [02 01 01 08 ] > Supervisory frame: > SAPI: 00 C/R: 1 EA: 0 > TEI: 000 EA: 1 > Zero: 0 S: 0 01: 1 [ RR (receive ready) ] > N(R): 004 P/F: 0 > 0 bytes of data -- Restarting T203 counter -- Restarting T203 counter Thanks, Daniel _______________________________________________ Asterisk-Users mailing list [EMAIL PROTECTED] http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-usersSteveOn Wed, 7 Jan 2004, Daniel Bichara wrote:Hi, I am trying to connect * E100P directly to Cisco using an ATM circuit. The ATM circuit is ok (I can connect to Ciscos). I do not understando too much about Cisco syntax, please help me. ############# Cisco Conf: isdn switch-type primary-net5 isdn voice-call-failure 0 controller E1 3 framing NO-CRC4 clock source line primary pri-group timeslots 1-31 interface Serial3:15 no ip address isdn switch-type primary-net5 isdn overlap-receiving T302 2000 isdn incoming-voice modem isdn send-alerting no cdp enable ############# Zaptel.Conf: span=2,1,0,ccs,hdb3,yellow bchan=32-46,48-62 dchan=47 ############# Zapata.conf: callwaiting=yes callwaitingcallerid=yes threewaycalling=no transfer=no cancallforward=no callreturn=no echocancel=yes echocancelwhenbridged=yes group = 2 signalling = pri_net switchtype = national channel => 32-46 channel => 48-62 Thanks in advance, Daniel _______________________________________________ Asterisk-Users mailing list [EMAIL PROTECTED] http://lists.digium.com/mailman/listinfo/asterisk-users_______________________________________________ Asterisk-Users mailing list [EMAIL PROTECTED] http://lists.digium.com/mailman/listinfo/asterisk-users |
- [Asterisk-Users] E1 - E100P connected to Cisco - problem Daniel Bichara
- Re: [Asterisk-Users] E1 - E100P connected to Cisco ... Stephen J. Wilcox
- Daniel Bichara