Good rewrite, but what about 1877 calls? -----Original Message----- From: asterisk-users-boun...@lists.digium.com [mailto:asterisk-users-boun...@lists.digium.com] On Behalf Of Martin Sent: Tuesday, May 19, 2009 11:28 AM To: Asterisk Users Mailing List - Non-Commercial Discussion Subject: Re: [asterisk-users] Dialplan Priorities and Sort Order...
ok, if 18xx are to go through analog lines and the rest through PRI then it's simply exten => _18XXNXXXXXX,1,Dial(zap/g1/${EXTEN}) exten => _18XXNXXXXXX,n,Hangup exten => _1[2-79]XXNXXXXXX,1,Dial(zap/g0/${EXTEN}) exten => _1[2-79]XXNXXXXXX,n,Hangup() Martin On Tue, May 19, 2009 at 11:00 AM, Danny Nicholas <da...@debsinc.com> wrote: > The first _1866 line should start a new segment of the dialplan. The way > this should work is 1800 and 1866 go out on zap /g1; anything else falls > into zap/g0. > > -----Original Message----- > From: asterisk-users-boun...@lists.digium.com > [mailto:asterisk-users-boun...@lists.digium.com] On Behalf Of Tim Nelson > Sent: Tuesday, May 19, 2009 10:38 AM > To: Asterisk Users Mailing List - Non-Commercial Discussion > Subject: [asterisk-users] Dialplan Priorities and Sort Order... > > Greetings! > > I'm hoping someone can help me with what should be the most basic of > problems. Essentially, I want to have certain calls on an Asterisk 1.2.25 > (Yes I know its old, upgrade, etc... its on my roadmap) install go out a > couple of analog lines and all other calls go out a PRI. The analog lines > are setup in Zaptel group 1 and the PRI channels are in Zaptel group 0. Here > is my relevant config: > > ; Outbound via POTS > [general-outbound] > exten => _1800NXXXXXX,1,Dial(ZAP/g1/${EXTEN}) > exten => _1800NXXXXXX,n,Answer > exten => _1800NXXXXXX,n,Busy > exten => _1800NXXXXXX,n,Hangup > exten => _1866NXXXXXX,n,Dial(ZAP/g1/${EXTEN}) > exten => _1866NXXXXXX,n,Answer > exten => _1866NXXXXXX,n,Busy > exten => _1866NXXXXXX,n,Hangup > include => pri_outbound > > ; Outbound via PRI > [pri_outbound] > exten => _X.,101,Dial(ZAP/g0/${EXTEN}) > exten => _X.,102,Answer > exten => _X.,103,Busy > exten => _X.,104,Hangup > > I certainly cannot be the only one who wants this sort of setup... correct? > Is it the way I'm including the other context, the dial patterns, the > priorities, etc? I'm not opposed to combining it into a single context, I > just started it out with this way. All hints are appreciated. (Pun > intended.. :-) ) > > --Tim > > _______________________________________________ > -- Bandwidth and Colocation Provided by http://www.api-digital.com -- > > asterisk-users mailing list > To UNSUBSCRIBE or update options visit: > http://lists.digium.com/mailman/listinfo/asterisk-users > > > _______________________________________________ > -- Bandwidth and Colocation Provided by http://www.api-digital.com -- > > asterisk-users mailing list > To UNSUBSCRIBE or update options visit: > http://lists.digium.com/mailman/listinfo/asterisk-users > _______________________________________________ -- Bandwidth and Colocation Provided by http://www.api-digital.com -- asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users _______________________________________________ -- Bandwidth and Colocation Provided by http://www.api-digital.com -- asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users