I try to use hylafax to send fax, but i encounter with TRAINING failed error I try many times to send a fax to fax machine whose type is Canon Laser Class 9000 Series I always failed with the TRAINING failed error but succeed 2-3 times I also send fax to another machine whose type is Panasonic And I failed all the time with the same error without any success
When using windows's fax modem to fax to the fax machine , I can fax successfully,so the fax machine is working well, and the problem is related to the hylafax or something else that i can't figure out I hava install spandsp-0.0.6,iaxmodem-1.2.0, hylafax-6.0.3 my asterisk version is 1.4.25.1, my TDM card's type is sangoma's 4 FXO port A200TDM card and my configure are the following: /var/spool/hylafax/etc/config.tty125 ================================================================================= CountryCode: 86 AreaCode: 020 FAXNumber: 28683014 LongDistancePrefix: 1 InternationalPrefix: 011 DialStringRules: etc/dialrules ServerTracing: 1 SessionTracing: 11 RecvFileMode: 0660 LogFileMode: 0600 DeviceMode: 0600 RingsBeforeAnswer: 1 SpeakerVolume: off GettyArgs: "-h %l dx_%s" LocalIdentifier: "OC9 Technologies" TagLineFont: etc/lutRS18.pcf TagLineFormat: "From %%l|%c|Page %%P of %%T" MaxRecvPages: 175 # # # Modem-related stuff: should reflect modem command interface # and hardware connection/cabling (e.g. flow control). # ModemType: Class1 # use this to supply a hint # # Enabling this will use the hfaxd-protocol to set Caller*ID # #ModemSetOriginCmd: AT+VSID="%s","%d" # # If "glare" during initialization becomes a problem then take # the modem off-hook during initialization, and then place it # back on-hook when done. # #ModemResetCmds: "ATH1\nAT+VCID=1" # enables CallID display #ModemReadyCmds: ATH0 Class1AdaptRecvCmd: AT+FAR=1 Class1TMConnectDelay: 1000 # counteract quick CONNECT response # # If you have trouble with V.17 receiving or sending, # you may want to enable one of these, respectively. # Class1RMQueryCmd: "!24,48,72,96" # enable this to disable V.17 receiving Class1TMQueryCmd: "!24,48,72,96" # enable this to disable V.17 sending Class1ResponseWaitCmd: AT+FRS=1 # # You'll likely want Caller*ID display (also displays DID) enabled. # ModemResetCmds: AT+VCID=1 # enables CallID display # # The pty does not support changing parity. # PagerTTYParity: none # # If you are "missing" Caller*ID data on some calls (but not all) # and if you do not have adequate glare protection you may want to # not answer based on RINGs, but rather enable the CallIDAnswerLength # for NDID, disable AT+VCID=1 and do this: # #RingsBeforeAnswer: 0 #ModemRingResponse: AT+VRID=1 # Uncomment DATE and TIME if you really want them, but you probably don't. #CallIDPattern: "DATE=" #CallIDPattern: "TIME=" CallIDPattern: "NMBR=" CallIDPattern: "NAME=" CallIDPattern: "ANID=" #CallIDPattern: "USER=" # username provided by call #CallIDPattern: "PASS=" # password provided by call #CallIDPattern: "CDID=" # DID context in call CallIDPattern: "NDID=" #CallIDAnswerLength: 4 ============================================================================================ /etc/iaxmodem/tty125 ====================================================================== device /dev/tty125 owner uucp:uucp mode 660 port 4570 refresh 50 server 127.0.0.1 peername 125 secret 125 codec alaw ======================================================================= my asterisk's config are following: /etc/asterisk/iax.conf ===================================================================== [125] type=friend secret=125 host=dynamic qualify=yes context=fax_out allow=alaw =========================================================================== /etc/asterisk/extensions.conf ============================================================================ [fax_out] exten => _X.,1,answer exten => _X.,n,Dial(ZAP/g0/${EXTEN}) ============================================================================== when I use the command sendfax -n -d 81094660 /var/spool/asterisk/fax/11.tif I can connect to the remote fax machine,but come to a TRAINING failed as an end here's my log's detail: ================================================================================================================ Aug 29 09:45:30.63: [ 9568]: SESSION BEGIN 000000113 8602028683015 Aug 29 09:45:30.63: [ 9568]: HylaFAX (tm) Version 6.0.3 Aug 29 09:45:30.63: [ 9568]: SEND FAX: JOB 60 DEST 28683015 COMMID 000000113 DEVICE '/dev/tty125' FROM 'root <r...@elastix.example.com>' USER root Aug 29 09:45:30.63: [ 9568]: <-- [12:AT+FCLASS=1\r] Aug 29 09:45:30.63: [ 9568]: --> [2:OK] Aug 29 09:45:30.65: [ 9568]: DIAL 28683015 Aug 29 09:45:30.65: [ 9568]: <-- [13:ATDT28683015\r] Aug 29 09:45:44.67: [ 9568]: --> [7:CONNECT] Aug 29 09:45:46.25: [ 9568]: --> [2:OK] Aug 29 09:45:46.25: [ 9568]: REMOTE NSF "00 00 0E 00 00 00 16 0F 41 07 00 10 00 02 95 C8 08" Aug 29 09:45:46.25: [ 9568]: NSF remote fax equipment: Panasonic Aug 29 09:45:46.25: [ 9568]: <-- [9:AT+FRH=3\r] Aug 29 09:45:46.61: [ 9568]: --> [7:CONNECT] Aug 29 09:45:46.67: [ 9568]: --> [2:OK] Aug 29 09:45:46.67: [ 9568]: REMOTE best rate 9600 bit/s Aug 29 09:45:46.67: [ 9568]: REMOTE max A4 page width (215 mm) Aug 29 09:45:46.67: [ 9568]: REMOTE max unlimited page length Aug 29 09:45:46.67: [ 9568]: REMOTE best vres 15.4 line/mm Aug 29 09:45:46.67: [ 9568]: REMOTE format support: MH, MR Aug 29 09:45:46.67: [ 9568]: REMOTE best 20 ms/scanline Aug 29 09:45:46.67: [ 9568]: USE 9600 bit/s Aug 29 09:45:46.67: [ 9568]: SEND file "docq/doc60.tif;70" Aug 29 09:45:46.67: [ 9568]: USE A4 page width (215 mm) Aug 29 09:45:46.67: [ 9568]: USE unlimited page length Aug 29 09:45:46.67: [ 9568]: USE 3.85 line/mm Aug 29 09:45:46.67: [ 9568]: USE 2-D MR Aug 29 09:45:46.67: [ 9568]: USE 20 ms/scanline Aug 29 09:45:46.67: [ 9568]: SEND training at v.29 9600 bit/s Aug 29 09:45:46.67: [ 9568]: <-- [9:AT+FRS=7\r] Aug 29 09:45:46.73: [ 9568]: --> [2:OK] Aug 29 09:45:46.73: [ 9568]: <-- [9:AT+FTH=3\r] Aug 29 09:45:46.75: [ 9568]: --> [7:CONNECT] Aug 29 09:45:46.75: [ 9568]: <-- data [23] Aug 29 09:45:46.75: [ 9568]: <-- data [2] Aug 29 09:45:48.31: [ 9568]: --> [7:CONNECT] Aug 29 09:45:48.31: [ 9568]: <-- data [6] Aug 29 09:45:48.31: [ 9568]: <-- data [2] Aug 29 09:45:48.67: [ 9568]: --> [2:OK] Aug 29 09:45:48.67: [ 9568]: <-- [9:AT+FTS=7\r] Aug 29 09:45:48.75: [ 9568]: --> [2:OK] Aug 29 09:45:48.75: [ 9568]: <-- [10:AT+FTM=96\r] Aug 29 09:45:48.77: [ 9568]: --> [7:CONNECT] Aug 29 09:45:48.77: [ 9568]: DELAY 1000 ms Aug 29 09:45:49.77: [ 9568]: <-- data [1024] Aug 29 09:45:49.77: [ 9568]: <-- data [776] Aug 29 09:45:49.77: [ 9568]: <-- data [2] Aug 29 09:45:51.34: [ 9568]: --> [2:OK] Aug 29 09:45:51.34: [ 9568]: <-- [9:AT+FRS=1\r] Aug 29 09:45:51.36: [ 9568]: --> [2:OK] Aug 29 09:45:51.36: [ 9568]: <-- [9:AT+FRH=3\r] Aug 29 09:45:51.54: [ 9568]: --> [7:CONNECT] Aug 29 09:45:52.69: [ 9568]: --> [2:OK] Aug 29 09:45:52.69: [ 9568]: SEND training at v.29 7200 bit/s Aug 29 09:45:52.69: [ 9568]: <-- [9:AT+FRS=7\r] Aug 29 09:45:52.75: [ 9568]: --> [2:OK] Aug 29 09:45:52.75: [ 9568]: <-- [9:AT+FTH=3\r] Aug 29 09:45:52.76: [ 9568]: --> [7:CONNECT] Aug 29 09:45:52.76: [ 9568]: <-- data [23] Aug 29 09:45:52.76: [ 9568]: <-- data [2] Aug 29 09:45:54.31: [ 9568]: --> [7:CONNECT] Aug 29 09:45:54.31: [ 9568]: <-- data [6] Aug 29 09:45:54.31: [ 9568]: <-- data [2] Aug 29 09:45:54.67: [ 9568]: --> [2:OK] Aug 29 09:45:54.67: [ 9568]: <-- [9:AT+FTS=7\r] Aug 29 09:45:54.77: [ 9568]: --> [2:OK] Aug 29 09:45:54.77: [ 9568]: <-- [10:AT+FTM=72\r] Aug 29 09:45:54.79: [ 9568]: --> [7:CONNECT] Aug 29 09:45:54.79: [ 9568]: DELAY 1000 ms Aug 29 09:45:55.79: [ 9568]: <-- data [1024] Aug 29 09:45:55.79: [ 9568]: <-- data [326] Aug 29 09:45:55.79: [ 9568]: <-- data [2] Aug 29 09:45:57.35: [ 9568]: --> [2:OK] Aug 29 09:45:57.35: [ 9568]: <-- [9:AT+FRS=1\r] Aug 29 09:45:57.37: [ 9568]: --> [2:OK] Aug 29 09:45:57.37: [ 9568]: <-- [9:AT+FRH=3\r] Aug 29 09:45:57.54: [ 9568]: --> [7:CONNECT] Aug 29 09:45:58.69: [ 9568]: --> [2:OK] Aug 29 09:45:58.69: [ 9568]: SEND training at v.27ter 4800 bit/s Aug 29 09:45:58.69: [ 9568]: <-- [9:AT+FRS=7\r] Aug 29 09:45:58.75: [ 9568]: --> [2:OK] Aug 29 09:45:58.75: [ 9568]: <-- [9:AT+FTH=3\r] Aug 29 09:45:58.77: [ 9568]: --> [7:CONNECT] Aug 29 09:45:58.77: [ 9568]: <-- data [23] Aug 29 09:45:58.77: [ 9568]: <-- data [2] Aug 29 09:46:00.32: [ 9568]: --> [7:CONNECT] Aug 29 09:46:00.32: [ 9568]: <-- data [6] Aug 29 09:46:00.32: [ 9568]: <-- data [2] Aug 29 09:46:00.68: [ 9568]: --> [2:OK] Aug 29 09:46:00.69: [ 9568]: <-- [9:AT+FTS=7\r] Aug 29 09:46:00.77: [ 9568]: --> [2:OK] Aug 29 09:46:00.77: [ 9568]: <-- [10:AT+FTM=48\r] Aug 29 09:46:00.79: [ 9568]: --> [7:CONNECT] Aug 29 09:46:00.79: [ 9568]: DELAY 1000 ms Aug 29 09:46:01.79: [ 9568]: <-- data [900] Aug 29 09:46:01.79: [ 9568]: <-- data [2] Aug 29 09:46:03.37: [ 9568]: --> [2:OK] Aug 29 09:46:03.37: [ 9568]: <-- [9:AT+FRS=1\r] Aug 29 09:46:03.39: [ 9568]: --> [2:OK] Aug 29 09:46:03.39: [ 9568]: <-- [9:AT+FRH=3\r] Aug 29 09:46:04.05: [ 9568]: --> [7:CONNECT] Aug 29 09:46:05.24: [ 9568]: --> [2:OK] Aug 29 09:46:05.24: [ 9568]: SEND training at v.27ter fallback mode 2400 bit/s Aug 29 09:46:05.24: [ 9568]: <-- [9:AT+FRS=7\r] Aug 29 09:46:05.30: [ 9568]: --> [2:OK] Aug 29 09:46:05.30: [ 9568]: <-- [9:AT+FTH=3\r] Aug 29 09:46:05.32: [ 9568]: --> [7:CONNECT] Aug 29 09:46:05.32: [ 9568]: <-- data [23] Aug 29 09:46:05.32: [ 9568]: <-- data [2] Aug 29 09:46:06.88: [ 9568]: --> [7:CONNECT] Aug 29 09:46:06.88: [ 9568]: <-- data [6] Aug 29 09:46:06.88: [ 9568]: <-- data [2] Aug 29 09:46:07.24: [ 9568]: --> [2:OK] Aug 29 09:46:07.24: [ 9568]: <-- [9:AT+FTS=7\r] Aug 29 09:46:07.34: [ 9568]: --> [2:OK] Aug 29 09:46:07.34: [ 9568]: <-- [10:AT+FTM=24\r] Aug 29 09:46:07.36: [ 9568]: --> [7:CONNECT] Aug 29 09:46:07.36: [ 9568]: DELAY 1000 ms Aug 29 09:46:08.36: [ 9568]: <-- data [450] Aug 29 09:46:08.36: [ 9568]: <-- data [2] Aug 29 09:46:09.94: [ 9568]: --> [2:OK] Aug 29 09:46:09.94: [ 9568]: <-- [9:AT+FRS=1\r] Aug 29 09:46:09.96: [ 9568]: --> [2:OK] Aug 29 09:46:09.96: [ 9568]: <-- [9:AT+FRH=3\r] Aug 29 09:46:11.13: [ 9568]: --> [7:CONNECT] Aug 29 09:46:12.30: [ 9568]: --> [2:OK] Aug 29 09:46:12.30: [ 9568]: TRAINING failed Aug 29 09:46:12.30: [ 9568]: <-- [9:AT+FRS=7\r] Aug 29 09:46:12.36: [ 9568]: --> [2:OK] Aug 29 09:46:12.36: [ 9568]: <-- [9:AT+FTH=3\r] Aug 29 09:46:12.38: [ 9568]: --> [7:CONNECT] Aug 29 09:46:12.38: [ 9568]: <-- data [3] Aug 29 09:46:12.38: [ 9568]: <-- data [2] Aug 29 09:46:13.47: [ 9568]: --> [2:OK] Aug 29 09:46:14.47: [ 9568]: <-- [5:ATH0\r] Aug 29 09:46:14.58: [ 9568]: --> [2:OK] Aug 29 09:46:14.58: [ 9568]: SESSION END ==================================================================================================== is there something wrong with my configure or this is my TDM card's problem, any help for this is very appreciated, thanks in advance and before this ,I use rxfax and txfax application to send and receive fax, i can receive fax successfully and failed to send fax, any help for this is a big grace to me, thanks all ~
_______________________________________________ -- Bandwidth and Colocation Provided by http://www.api-digital.com -- AstriCon 2009 - October 13 - 15 Phoenix, Arizona Register Now: http://www.astricon.net asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users