Re: [asterisk-users] More Echo

[Jason Baker]

Title: Jason Baker - Signature

Thank you. I will do that. Jason Baker IT Coordinator Glastender, Inc. 5400 North Michigan Road Saginaw, Michigan 48604 USA Phone: 989.752.4275 ext. 228 Fax: 989.752.4276 www.glastender.com John wrote: You should also get your t1 carrier to provide echo cans on the circuit. Fairly common and easy for them to set up. John Chastain On Sep 4, 2009, at 3:07 PM, Steve Totaro <stot...@asteriskhelpdesk.com> wrote: 2009/9/4 Vinícius Fontes <vinic...@canall.com.br> No it's not a fact of life. VoIP works as fine as conventional telephony once it's correctly set up. Try echocancel=256 instead of echocancel=yes and also run fxotune (check the man page). If that all fails, install OSLEC. It's an excellent free software echo canceller, that works much better than Asterisk's default MG2. Vinícius Fontes www.asteriskforum.com.br - Informações e discussão sobre Asterisk e telefonia IP ----- "Jason Baker" <jba...@glastender.com> escreveu: > Well I tried Doug's suggestion and the echo is now better, but when I > call an outside analog line I still get some echo. I can hear my voice > in the ear piece of the phone with a slight delay. Is this just a fact > of life with VoIP, or is there a better way to reduce line echo? > > Again, for reference, I am using the VPMADT032 echo cancellation > module attached to a Digium TE121 PCI express card. The incoming phone > service is a PRI. > > > > Jason Baker > IT Coordinator Glastender, Inc. > 5400 North Michigan Road > Saginaw, Michigan 48604 USA > Phone: 989.752.4275 ext. 228 > Fax: 989.752.4276 > www.glastender.com > > Doug Lytle wrote: > > Jason Baker wrote: > > language = en > > group = 1 > echocancel = yes > echotraining = yes > signalling = pri_cpe > switchtype = 4ess > usecallerid = yes > context = incoming > channel => 1-23 Just noted that your system is out of Saginaw.  The > system below is out > of Livonia, with an AT&T PRI as well.  Note the rx/txgain entries, it > may be useful as well: > > > switchtype=national > context=pri > signalling=pri_cpe > echocancel=yes > echotraining=yes > echocancelwhenbridged=yes > rxgain=-1.0 > txgain=-4.0 Just curious.  Have you tried turning off all echo can?  I RARELY need echo can on T-1. I was also under the impression that rx/tx gain was only for POTS lines. -- Thanks, Steve Totaro +12409381212 (Cell) +12024369784 (Skype) _______________________________________________ -- Bandwidth and Colocation Provided by http://www.api-digital.com -- AstriCon 2009 - October 13 - 15 Phoenix, Arizona Register Now: http://www.astricon.net asterisk-users mailing list To UNSUBSCRIBE or update options visit:   http://lists.digium.com/mailman/listinfo/asterisk-users _______________________________________________ -- Bandwidth and Colocation Provided by http://www.api-digital.com -- AstriCon 2009 - October 13 - 15 Phoenix, Arizona Register Now: http://www.astricon.net asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users

_______________________________________________
-- Bandwidth and Colocation Provided by http://www.api-digital.com --

AstriCon 2009 - October 13 - 15 Phoenix, Arizona
Register Now: http://www.astricon.net

asterisk-users mailing list
To UNSUBSCRIBE or update options visit:
   http://lists.digium.com/mailman/listinfo/asterisk-users