Hi everyone. We have a problem here... Hope somebody can give us some hints.
We have a HP ProLiant DL180 G6 Server with a Debian/Lenny sytem. Asterisk 1.4.21.2 (1.4.21.2~dfsg-3+lenny1) with zaptel (1.4.11) and libpri (1.4.3) is installed. There is a QuadBRI-Card installed: # lspci -vv -s 06:04.0 06:04.0 ISDN controller: Cologne Chip Designs GmbH ISDN network Controller [HFC-4S] (rev 01) Subsystem: Cologne Chip Designs GmbH Device b752 Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Interrupt: pin A routed to IRQ 30 Region 0: I/O ports at cc00 [size=8] Region 1: Memory at fb6ff000 (32-bit, non-prefetchable) [size=4K] Capabilities: [40] Power Management version 2 Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- zttest gives me an average of 99.992% and zttool shows no alarms. But every about 3,5 minutes we get this (with "debug span 1" enababled): 1 -- Timeout occured, restarting PRI 1 q921.c:859 t200_expire: q921_state now is Q921_LINK_CONNECTION_RELEASED 1 Sending Set Asynchronous Balanced Mode Extended 1 q921.c:534 q921_send_sabme: q921_state now is Q921_AWAITING_ESTABLISH == Primary D-Channel on span 1 down [Apr 10 12:16:05] WARNING[28541]: chan_zap.c:2498 pri_find_dchan: No D-channels available! Using Primary channel 3 as D-channel anyway! 1 Sending Set Asynchronous Balanced Mode Extended 1 -- Got UA from network peer Link up. 1 -- Restarting T203 counter == Primary D-Channel on span 1 up % cat /etc/zaptel.con # Autogenerated by /usr/sbin/genzaptelconf -- do not hand edit # Zaptel Configuration File # # This file is parsed by the Zaptel Configurator, ztcfg # # It must be in the module loading order # Span 1: ztqoz/1/1 "quadBRI PCI ISDN Card 1 Span 1 [TE] (cardID 0)" (MASTER) span=1,1,3,ccs,ami # termtype: te bchan=1-2 dchan=3 # Span 2: ztqoz/1/2 "quadBRI PCI ISDN Card 1 Span 2 [TE] (cardID 0)" span=2,2,0,ccs,ami # termtype: te bchan=4-5 dchan=6 # Span 3: ztqoz/1/3 "quadBRI PCI ISDN Card 1 Span 3 [TE] (cardID 0)" span=3,3,0,ccs,ami # termtype: te bchan=7-8 dchan=9 # Span 4: ztqoz/1/4 "quadBRI PCI ISDN Card 1 Span 4 [TE] (cardID 0)" span=4,4,0,ccs,ami # termtype: te bchan=10-11 dchan=12 # Global data loadzone = at defaultzone = at % cat /etc/asterisk/zapata.conf [channels] language=de switchtype=euroisdn pridialplan=unknown prilocaldialplan=dynamic priindication=passthrough context=incoming immediate=no usecallingpres=yes usecallerid=yes group=1 nationalprefix=00 internationalprefix=000 signalling=bri_cpe echocancel=Yes overlapdial=Yes ; group=2 ; signalling=bri_cpe ; context=incoming ; channel => 10-11 ; channel => 1-2 ; channel => 4-5 ; channel => 7-8 ; channel => 10-11 (Only one span is connected to ISDN right now.) qozap is loaded and ztcfg -v gives me: Zaptel Version: 1.4.11 Echo Canceller: MG2 Configuration ====================== SPAN 1: CCS/ AMI Build-out: 399-533 feet (DSX-1) SPAN 2: CCS/ AMI Build-out: 0 db (CSU)/0-133 feet (DSX-1) SPAN 3: CCS/ AMI Build-out: 0 db (CSU)/0-133 feet (DSX-1) SPAN 4: CCS/ AMI Build-out: 0 db (CSU)/0-133 feet (DSX-1) 12 channels to configure. Any idea what this could mean and how this could be fixed? Any help would be helpful. Thx. Greetings, - Darsha -- _____________________________________________________________________ -- Bandwidth and Colocation Provided by http://www.api-digital.com -- New to Asterisk? Join us for a live introductory webinar every Thurs: http://www.asterisk.org/hello asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users