Hello Rich, Sunday, January 25, 2004, 8:01:25 PM, you wrote:
RA> It would probably help if you used a packet sniffer (eg, ethereal) to look RA> at the traffic, or at least provide the list with a useful clue other then RA> it doesn't work. RA> ------------------------ >> same here, when i recive an incoming call from x100p to line 1 on >> sipura, i can hear them but people can't hear me im using 1.0.24 on my >> firmware >> >> Miguel >> On Sun, 2004-01-25 at 20:54, Chris Higgins wrote: >> > Frankie Gravato wrote: >> > >> > > >> > > I've been beating my head for 5 hours to figure out why my asterisk >> > > server or sipura isn't passing my voice over to the caller. It seems i >> > > can hear the caller but they can't hear me it seems either the >> > > asterisk or the sipura isn't passing this information. >> > > >> > > Here's my setup specs >> > > >> > > asterisk server 0.7.1 - X100P Card - Sipura 2000 - Nufone Service - >> > > Voicepulse Service and DID's >> > > >> > > when i get Phone call using the Voicepulse or Pstn the caller can't >> > > hear me or barely hear me. The Sipura is running Firmware 1.20 and >> > > calls are being passed using Ulaw Codec? Anyone out there in the >> > > asterisk community please oh please help me before i do something that >> > > my asterisk server won't like. >> > > >> > > >> > >> > I just received my Sipura on Friday and have been testing it extensively >> > over the weekend. I have noticed an issue similar to what you mention >> > above. For the record, the sipura tells me I'm running software version >> > 1.0.20. Also, there is NO nat configuration that is causing my problem. >> > >> > When I receive a call over my X100P and dial my 3 SIP phones (one gs >> > budgetone 100, two analong phones through sipura), if I answer the >> > analong phone connected to line 1 of the sipura, the caller cannot hear >> > anything. I've only noticed this problem in this exact scenario. The >> > other situations listed below have no problems whatsoever and audio >> > works in both directions: >> > >> > 1. Call from sipura line 1 to any internal SIP phone. >> > 1. Call from any internal SIP phone to sipura line 1. >> > 2. Call from sipura line 1 out through X100P. >> > 3. Call into my X100P from outside and answer sipura line 2. >> > 4. Call into my X100P from outside and answer sipura line 2 and THEN >> > transfer to sipura line 1. >> > 5. Call into my X100P from outside and answer sipura line 1 (the caller >> > cannot hear audio for this leg of the conversation), TRANSFER to any >> > other line, and transfer back to sipura line 1. After the second >> > transfer, the caller can hear audio from sipura line 1. >> > >> > I don't know what is special about line 1. I've switched my analog >> > phones across the two ports on the sipura to make sure it wasn't one of >> > my phones (not that I thought it was anyway). >> > >> > Frankie, have you tried the same experiment, but pulled your analog >> > phone from line 1 and put it in line 2? >> > >> > Has anyone else seen issues like this with line 1 on a sipura? >> > >> > Thanks.. >> > >> > -- Chris >> > _______________________________________________ >> > Asterisk-Users mailing list >> > [EMAIL PROTECTED] >> > http://lists.digium.com/mailman/listinfo/asterisk-users >> > To UNSUBSCRIBE or update options visit: >> > http://lists.digium.com/mailman/listinfo/asterisk-users >> _______________________________________________ >> Asterisk-Users mailing list >> [EMAIL PROTECTED] >> http://lists.digium.com/mailman/listinfo/asterisk-users >> To UNSUBSCRIBE or update options visit: >> http://lists.digium.com/mailman/listinfo/asterisk-users RA> ---------------End of Original Message----------------- RA> _______________________________________________ RA> Asterisk-Users mailing list RA> [EMAIL PROTECTED] RA> http://lists.digium.com/mailman/listinfo/asterisk-users RA> To UNSUBSCRIBE or update options visit: RA> http://lists.digium.com/mailman/listinfo/asterisk-users I'll be trying that as my next step but it seems that my other fresh - sipura 2000 unit that was sitting in the box which is running 1.0.15 firmware seems to work seamless so i find it odd ? that brand new unit works while the upgraded firmware ones don't? I'm not the only one having this same exact issue I've received 4 emails relating to the same issue from other users. So there's some kind trend going on with this? -- Best regards, Frankie ([EMAIL PROTECTED]) mailto:[EMAIL PROTECTED] _______________________________________________ Asterisk-Users mailing list [EMAIL PROTECTED] http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users