Am I getting these error messages due to wrong configurations in my zapata.conf. ??
I have got the following configurations in my zapata-channels.conf. ; Span 1: WCT1/0 "Wildcard TE122 Card 0" (MASTER) B8ZS/ESF RED group=0,11 context=from-pstn switchtype = national signalling = pri_cpe channel => 1-23 group= context=default Najim On Fri, Sep 30, 2011 at 4:51 AM, NaJIm <getna...@gmail.com> wrote: > Hi Eric, > > This is the error messages I get I try to load the module. > > *CLI> module load chan_zap.so > [Sep 30 04:45:57] WARNING[5182]: pbx.c:2979 ast_register_application: > Already have an application 'ZapSendKeypadFacility' > == Parsing '/etc/asterisk/zapata.conf': Found > -- Registered channel 1, ISDN PRI signalling > -- Registered channel 2, ISDN PRI signalling > -- Registered channel 3, ISDN PRI signalling > -- Registered channel 4, ISDN PRI signalling > -- Registered channel 5, ISDN PRI signalling > -- Registered channel 6, ISDN PRI signalling > -- Registered channel 7, ISDN PRI signalling > -- Registered channel 8, ISDN PRI signalling > -- Registered channel 9, ISDN PRI signalling > -- Registered channel 10, ISDN PRI signalling > -- Registered channel 11, ISDN PRI signalling > -- Registered channel 12, ISDN PRI signalling > -- Registered channel 13, ISDN PRI signalling > -- Registered channel 14, ISDN PRI signalling > -- Registered channel 15, ISDN PRI signalling > -- Registered channel 17, ISDN PRI signalling > -- Registered channel 18, ISDN PRI signalling > -- Registered channel 19, ISDN PRI signalling > -- Registered channel 20, ISDN PRI signalling > -- Registered channel 21, ISDN PRI signalling > -- Registered channel 22, ISDN PRI signalling > -- Registered channel 23, ISDN PRI signalling > [Sep 30 04:45:57] WARNING[5182]: chan_zap.c:905 zt_open: Unable to specify > channel 24: Device or resource busy > [Sep 30 04:45:57] ERROR[5182]: chan_zap.c:7219 mkintf: Unable to open > channel 24: Device or resource busy > here = 0, tmp->channel = 24, channel = 24 > [Sep 30 04:45:57] ERROR[5182]: chan_zap.c:10582 build_channels: Unable to > register channel '17-31' > > > Regards, > Najim > > > On Fri, Sep 30, 2011 at 4:24 AM, Eric Wieling <ewiel...@nyigc.com> wrote: > >> Try "module load chan_zap.so" in the CLI. You should see whatever errors >> are generated. >> >> -----Original Message----- >> From: asterisk-users-boun...@lists.digium.com [mailto: >> asterisk-users-boun...@lists.digium.com] On Behalf Of NaJIm >> Sent: Thursday, September 29, 2011 5:52 PM >> To: Asterisk Users Mailing List - Non-Commercial Discussion >> Subject: [asterisk-users] [asterik-users] Installing PRI card >> >> Hi, >> >> We have got a new PRI card at one of our Office locations and now I need >> to install the the device on a remote server. Is there any way to know if >> the device is loaded already. >> >> When I give " cat /proc/zaptel/* " it returns the following. >> >> >> # cat /proc/zaptel/* >> >> Span 1: WCT1/0 "Wildcard TE122 Card 0" (MASTER) >> B8ZS/ESF RED >> >> IRQ misses: 2 >> >> >> 1 WCT1/0/1 Clear (In use) RED >> >> 2 WCT1/0/2 Clear (In use) RED >> >> 3 WCT1/0/3 Clear (In use) RED >> >> 4 WCT1/0/4 Clear (In use) RED >> >> 5 WCT1/0/5 Clear (In use) RED >> >> 6 WCT1/0/6 Clear (In use) RED >> >> 7 WCT1/0/7 Clear (In use) RED >> >> 8 WCT1/0/8 Clear (In use) RED >> >> 9 WCT1/0/9 Clear (In use) RED >> >> 10 WCT1/0/10 Clear (In use) RED >> >> 11 WCT1/0/11 Clear (In use) RED >> >> 12 WCT1/0/12 Clear (In use) RED >> >> 13 WCT1/0/13 Clear (In use) RED >> >> 14 WCT1/0/14 Clear (In use) RED >> >> 15 WCT1/0/15 Clear (In use) RED >> >> 16 WCT1/0/16 Clear RED >> >> 17 WCT1/0/17 Clear (In use) RED >> >> 18 WCT1/0/18 Clear (In use) RED >> >> 19 WCT1/0/19 Clear (In use) RED >> >> 20 WCT1/0/20 Clear (In use) RED >> >> 21 WCT1/0/21 Clear (In use) RED >> >> 22 WCT1/0/22 Clear (In use) RED >> >> 23 WCT1/0/23 Clear (In use) RED >> >> 24 WCT1/0/24 HDLCFCS (In use) RED >> >> >> But when I connect to the console, I am unable to give any ZAP related >> commands. Does this mean that my device is loaded and I just need to load >> the module. Or do I need to compile asterisk again?? Any help would be >> highly appreciated. >> >> My asterisk version is Asterisk 1.4.19.2 and I am on a Fedora release 9 >> server. >> >> Thanks, >> Najim >> >> >> -- >> _____________________________________________________________________ >> -- Bandwidth and Colocation Provided by http://www.api-digital.com -- >> New to Asterisk? Join us for a live introductory webinar every Thurs: >> http://www.asterisk.org/hello >> >> asterisk-users mailing list >> To UNSUBSCRIBE or update options visit: >> http://lists.digium.com/mailman/listinfo/asterisk-users >> > >
-- _____________________________________________________________________ -- Bandwidth and Colocation Provided by http://www.api-digital.com -- New to Asterisk? Join us for a live introductory webinar every Thurs: http://www.asterisk.org/hello asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users