Hi Ernst, use this: exten => 74341423,1,Dial(Zap/g2/74341423,r) instead of: exten => 74341423,1,Dial(Zap/5/74341423,r)
-- best regards Klaus -- Klaus-Peter Junghanns CEO, CTO Junghanns.NET GmbH Breite Straße 13 - 12167 Berlin - Germany fon: (de) +49 30 79705390 fon: (uk) +44 870 1244692 fax: (de) +49 30 79705391 iaxtel: 1-700-157-8753 http://www.Junghanns.NET/asterisk/ Am Do, 2004-02-19 um 14.24 schrieb Ernst Lehmann: > Hi, > > Does anyone operate Asterisk with zaphfc in NT-Mode successfully ?? > > I have the problem, that I could not contact my ISDN-Phone on such a > channel. It rings, but If I pick up the phone, I only get a Hangup in > the console.... > > Thanks for any clues on it... > > Here my setup: > > 3 HFC Cards. > > first card is TE, other two are NT mode (loaded zaphfc with modes=6) > > The ISDN-Phone is connected to the second-card. The ISDN-Bus is powerd > by an old NTBA like described in the pbx4linux project Howto. > > /etc/zaptel.cfg > > ------------ > span=1,1,3,ccs,ami > bchan=1-2 > dchan=3 > span=2,0,3,ccs,ami > bchan=4-5 > dchan=6 > span=3,0,3,ccs,ami > bchan=7-8 > dchan=9 > ----------- > > /etc/asterisk/zapata.conf > > --------- > switchtype = euroisdn > signalling = bri_cpe_ptmp > pridialplan=unknown > echocancel=yes > immediate=no > group = 1 > context=prod > channel => 1-2 > > switchtype = euroisdn > signalling = bri_net_ptmp > pridialplan=unknown > group = 2 > context=prod > channel => 4-5 > ----------------- > > valid passage from extension.conf > > ------------------ > [prod] > .... > > exten => 74341423,1,Dial(Zap/5/74341423,r) > > ..... > > ------------------- > > The ISDN-Phone is configured to listen on the MSN 74341423 > > Here the log from the console: > > ----------- > > -- Executing Dial("Zap/2-1", "Zap/5/74341423|r") in new stack > -- Called 5/74341423 > -- Hungup 'Zap/5-1' > -- Accepting call from '8974341421' to '74341423' on channel 2, span > 1 > MFE for TEI = 64 > -- Timeout on Zap/2-1 > == CDR updated on Zap/2-1 > -- Executing Goto("Zap/2-1", "#|1") in new stack > -- Goto (prod,#,1) > -- Sent into invalid extension '#' in context 'prod' on Zap/2-1 > -- Executing SetVar("Zap/2-1", "starttime=1077196512") in new stack > -- Executing Playtones("Zap/2-1", "info") in new stack > -- Executing Wait("Zap/2-1", "1") in new stack > -- Executing Playback("Zap/2-1", "invalid") in new stack > -- Playing 'invalid' (language 'en') > -- Executing Wait("Zap/2-1", "1") in new stack > -- Executing GotoIf("Zap/2-1", "1?2:7") in new stack > -- Goto (prod,i,2) > -- Executing Playtones("Zap/2-1", "info") in new stack > -- Executing Wait("Zap/2-1", "1") in new stack > -- Executing Playback("Zap/2-1", "invalid") in new stack > -- Playing 'invalid' (language 'en') > -- Channel 2, span 1 got hangup > == Spawn extension (prod, i, 4) exited non-zero on 'Zap/2-1' > -- Hungup 'Zap/2-1' > > ----------------- > > perhaps helpfull... some information from dmesg on loading of modules: > > ------------- > Zapata Telephony Interface Registered on major 196 > zaphfc: start > PCI: Found IRQ 5 for device 00:09.0 > PCI: Sharing IRQ 5 with 00:04.3 > zaphfc: card configured at mem 0xc8875000 fifo 0xc70e8000(0x70e8000) IRQ > 5 HZ 10 > 0 > zaphfc: ZTHFC1/0/1 > zaphfc: ZTHFC1/0/2 > zaphfc: ZTHFC1/0/3 > zaphfc: registered zaptel device! > zaphfc: Card 0 configured for TE mode > zaphfc: resetting card. > zaphfc: layer 1 state = F4 > PCI: Found IRQ 12 for device 00:0a.0 > zaphfc: card configured at mem 0xc8877000 fifo 0xc7158000(0x7158000) IRQ > 12 HZ 1 > 00 > zaphfc: ZTHFC2/0/1 > zaphfc: ZTHFC2/0/2 > zaphfc: ZTHFC2/0/3 > zaphfc: registered zaptel device! > zaphfc: Card 1 configured for NT mode > zaphfc: resetting card. > zaphfc: layer 1 state = F5 > zaphfc: layer 1 state = F6 > zaphfc: layer 1 state = G2 > PCI: Found IRQ 10 for device 00:0b.0 > PCI: Sharing IRQ 10 with 00:11.0 > zaphfc: card configured at mem 0xc8879000 fifo 0xc7148000(0x7148000) IRQ > 10 HZ 1 > 00 > zaphfc: ZTHFC3/0/1 > zaphfc: ZTHFC3/0/2 > zaphfc: ZTHFC3/0/3 > zaphfc: registered zaptel device! > zaphfc: Card 2 configured for NT mode > zaphfc: resetting card. > zaphfc: bchan rx fifo not enough bytes to receive! (z1=518, z2=8191) > zaphfc: bchan rx fifo not enough bytes to receive! (z1=518, z2=8191) > zaphfc: 3 card(s) in this box. > Registered tone zone 3 (Netherlands) > zaphfc: layer 1 state = G3 > > ----------------------- _______________________________________________ Asterisk-Users mailing list [EMAIL PROTECTED] http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users